Renault TRAFIC 2022 User Manual

page of 410

/ 410
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

tRaFIC

vehicle user manual

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the TRAFIC 2022 and is the answer not in the manual?

Questions and answers

Summary of Contents for Renault TRAFIC 2022

Page 1 tRaFIC vehicle user manual...
Page 2 Castrol, exclusive Renault partner Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault thanks to wide range of engine lubricants developed specially by Renault and Castrol. Renault recommends renault.fr...
Page 3 Welcome to your new vehicle This user manual contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
Page 5 EXTERIOR Bodywork mainte- nance ➥ 4.14 Electric windows ➥ 3.18 Wiper ➥ 1.128 and ➥ 5.33 Demisting ➥ 3.4 and ➥ 3.8 Key/Remote control ➥ 1.2 Transmitter-receiver ➥ 1.8 Locking/unlocking the doors ➥ 1.32 Lights: operation ➥ 1.120 Rear view mirrors Lights: replacement ➥...
Page 6 PASSENGER COMPARTMENT Adjusting your driving po- Passenger compartment stor- sition ➥ 1.43 age/fittings ➥ 3.25 Rear bench seat ➥ 3.38 Rear headrests ➥ 1.39 Front seats ➥ 1.40 Front headrests ➥ 1.39 Child safety ➥ 1.63 Transporting objects ➥ 3.45...
Page 7 DRIVER’S POSITION I n s t r u m e n t p a n e l Exterior lights ➥ 1.120 Trip computer controls ➥ 1.115 ➥ 1.100 Multimedia screen ➥ 1.109 Heating/ heating and air condition- ing system ➥ 3.4 Cruise control ➥...
Page 8 DRIVING AIDS Active emergency braking ➥ 2.51 Speed limiter ➥ 2.63 Cruise control ➥ 2.67 Lane departure warning ➥ 2.36 Stop and Start ➥ 2.8 Parking distance control ➥ 2.88 Blind spot warning ➥ 2.41 Reversing camera ➥ 2.96 ABS (anti-lock braking system) ESC (electronic stability control) Tyre pressure loss warning Braking assistance...
Page 9 SAFETY ON BOARD Seat belts ➥ 1.43 Front Airbags ➥ 1.49 Inhibiting the front passen- ger airbag ➥ 1.91 Side Airbags ➥ 1.56...
Page 10 IDENTIFYING A VEHICLE - LABELS Review of a vehicle identification number ➥ 6.2 Vehicle identification plate ➥ 6.2 Technical Information for the emergency services ➥ 6.3 Engine identification ➥ 6.4 Tyre pressure labels ➥ 2.26 and ➥ 4.10...
Page 11 THE ENGINE COMPARTMENT (routine maintenance) Windscreen washer fluid ➥ 4.7 Engine oil dipstick ➥ 4.4 Battery ➥ 4.12 Brake fluid ➥ 4.7 Coolant level ➥ 4.7 Opening the bonnet ➥ 4.2 Engine oil filler cap ➥ 4.5...
Page 12 BREAKDOWN RECOVERY Replacing the windscreen Puncture: wiper blades ➥ 1.128 Tools ➥ 5.8 Emergency spare wheel ➥ 5.2 Changing a wheel ➥ 5.10 Replacing headlight bulbs ➥ 5.19 Front towing point ➥ 5.36 Replacing the rear screen wiper blade ➥ 1.132 Fuses ➥...
Page 13 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........0.11...
Page 14 0.12...
Page 15: Table Of Contents
Section 1: Getting to know your vehicle Keys, remote controls ............Card: general information, use, deadlocking .
Page 16 KEYS, RADIO FREQUENCY REMOTE CONTROLS: general information (1/3) Combi version A key, switchblade Combi version B key, remote remote control control 1 Locks all the opening elements. 4 Driver’s door and ignition key. 2 Unlocks all the opening elements. 5 Unlocking the luggage compartment only.
Page 17 KEYS, RADIO FREQUENCY REMOTE CONTROLS: general information (2/3) Van version C key, switchblade Van version D key, remote control remote control 9 Driver’s door and ignition key. 6 Locks all the opening elements. 10 Unlocking the sliding side doors and 7 Unlocking all the opening elements the rear hinged doors or the tailgate.
Page 18 KEYS, RADIO FREQUENCY REMOTE CONTROLS: general information (3/3) Radio frequency remote control operating range This varies according to the environ- ment: take care not to lock or unlock Replacement and additional keys the doors by inadvertently pressing the or remote controls buttons on the remote control.
Page 19 KEYS, RADIO FREQUENCY REMOTE CONTROL: use (1/2) Remote control A or, depending on the vehicle, remote control B locks or un- locks the doors. It is powered by a bat- tery which can be replaced ➥ 5.28. Locking the doors Press locking button 1.
Page 20 KEYS, RADIO FREQUENCY REMOTE CONTROL: use (2/2) Unlocking the doors The hazard lights and side repeaters flash once to indicate that the doors have unlocked and, on some vehicles, With the ignition on and engine run- the door mirrors fold out automatically. ning ➥...
Page 21 DEADLOCKING If the vehicle is equipped with a dead- To do this, press button 1 twice in quick locking function, this allows you to lock succession. the opening elements and to prevent The hazard warning lights and indicator the doors from being unlocked using lights give two slow flashes and three the interior handles (for example, by quick flashes to indicate locking.
Page 22 CARD: general information (1/4) Combi version card Van version card 1 Unlocking the doors and tailgate. 4 Switching on the lighting remotely. 2 Locking all doors and tailgate. 5 Unlocking the front doors and, de- pending on the vehicle, the sliding 3 Unlocking the luggage compartment side door in Secure mode, or un- only.
Page 23 CARD: general information (2/4) The card is used for: card operating range Battery life – locking/unlocking the doors and boot This varies according to the environ- Make sure that the correct battery type (see the following pages); ment: take care not to accidentally lock is being used, and that the battery is in or unlock the vehicle by inadvertently good condition and inserted correctly.
Page 24 CARD: general information (3/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone in your vehicle, even for a short time. They may pose a risk to themselves Distance lighting function or to others by starting the engine, Pressing button 4 switches on the...
Page 25 CARD: general information (4/4) Fitting a strap 10 Insert the hand strap into the 11 com- ponent and pass the end of the strap Slide the rear casing 8 downwards through the buckle. while pressing on zone A. Position the strap at the 9 opening and close the cartridge.
Page 26 “HANDS-FREE” CARD: use (1/10) Combi version card A There are three ways to unlock/lock the vehicle: – “hands-free”, when approaching and moving away from the vehicle; – in “hands-free” mode, using button 2 on the handle 1 of the driver’s door, the passenger’s door or the luggage compartment door;...
Page 27 “HANDS-FREE” CARD: use (2/10) Hands-free unlocking, when Hands-free locking when moving The vehicle cannot be remotely locked approaching the vehicle; away from the vehicle if the card is within the area 5. With the card in access zone 3, the ve- With the card on you, doors and lug- hicle will unlock.
Page 28 “HANDS-FREE” CARD: use (3/10) If the card has been within the detec- “Hands-free” unlocking/locking With the vehicle unlocked, press tion area 4 for approximately 15 min- using button 2 button 2 once to lock the vehicle. utes, remote locking is disabled. To lock With the card in zone 3 and the vehicle The hazard warning lights flash twice the vehicle, press the 2 button on one...
Page 29 “HANDS-FREE” CARD: use (4/10) Press button 2 or use the card as a remote control (see following pages) to unlock the vehicle and reactivate “hands-free” mode. Special features relating to “hands- free” locking After locking in hands-free mode, you have to wait approximately three sec- onds before being able to unlock the vehicle again.
Page 30 “HANDS-FREE” CARD: use (5/10) Locking using the card With the doors and boot closed, press button 6: the vehicle locks. The hazard warning lights flash twice to indicate that the vehicle is locked and, depending on the vehicle, the door mirrors automatically fold in.
Page 31 “HANDS-FREE” CARD: use (6/10) Van version card B Unlocking the vehicle There are two ways to unlock the ve- hicle: – in “hands-free” mode, using the but- tons on the door handles; – using the card in remote control mode. Locking the vehicle There are four ways to lock the vehicle: –...
Page 32 “HANDS-FREE” CARD: use (7/10) “Hands-free” unlocking The hazard lights and side repeaters If one of the opening elements in the flash once to indicate that the doors rear area is open, press the 9, 10 or 12 With the card in the access zone 11: have unlocked and, on some vehicles, button to lock the front doors.
Page 33 “HANDS-FREE” CARD: use (8/10) Special features relating to “hands- free” locking After locking in hands-free mode, you have to wait approximately three sec- onds before being able to unlock the vehicle again. Note: “hands-free” unlocking/locking will not work if the card is not present within the detection zone of the button pressed.
Page 34 “HANDS-FREE” CARD: use (9/10) Unlocking with the card Press the 16 button to unlock the rear, hinged or tailgate doors and, depending on the vehicle, the sliding side doors. Secure mode Press the 15 button to unlock the front doors and, depending on the vehicle, the sliding side door.
Page 35 “HANDS-FREE” CARD: use (10/10) Locking using the card With the doors and boot closed, press button 13: the vehicle locks. The hazard warning lights flash twice to indicate that the vehicle is locked and, depending on the vehicle, the door mirrors automatically fold in.
Page 36 CARD: deadlocking To activate deadlocking Press button 2 twice in quick succes- sion. Locking is confirmed by two slow flashes and three quick flashes of the hazard warning lights and side indica- tor lights. Depending on the vehicle, the door mir- rors fold in automatically when the vehi- cle is locked ➥...
Page 37 FRONT DOORS (1/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, Opening the doors from the Opening from the inside activating equipment such as the...
Page 38 FRONT DOORS (2/2) Lights-on reminder buzzer Special note If you have switched off the ignition Depending on the vehicle, accessories and left the lights switched on, a re- (e.g. radio) stop working either when minder buzzer will sound when a door the engine is switched off or when the is opened.
Page 39 SLIDING SIDE DOOR (1/2) Closing from the outside Pull handle 1 and slide the door to- wards the front of the vehicle until it closes completely. Closing from the inside Pull lever 3 towards the front and close the door until it latches. Manual locking from inside Lower button 4.
Page 40 SLIDING SIDE DOOR (2/2) Recommendations con- cerning the sliding side door. Care must be taken when opening or closing the sliding door, as is the case for any of the opening Driver’s responsibility elements on the vehicle: when parking or stopping the vehicle –...
Page 41 REAR HINGED DOORS (1/4) Opening the doors from the Pull the lever 3 to open the door. outside Vehicles with a remote control Unlock the vehicle using the remote control and pull handle 1. If the vehicle is parked Vehicles with card on the hard shoulder with With the card on your person, press the tailgate open, the rear...
Page 42 REAR HINGED DOORS (2/4) Driving with the right-hand When driving with the right- door open hand rear hinged door open, always secure trans- With the right-hand door open, close ported loads ➥ 3.45. The the left-hand door. left-hand door, which remains shut, On equipped vehicles, lock the left- should not be used to hold trans- hand door by turning the lock 5 to put it...
Page 43 REAR HINGED DOORS (3/4) Opening the doors to the Closing from the outside maximum position Partially close the right-hand door, then slam it shut. For each door, pull handle 6 to release the door check strap 7. Open the door Then repeat this with the left-hand door as far as possible.
Page 44 REAR HINGED DOORS (4/4) Opening from the inside Pull the handle 9 and push the door A. Pull the lever 3 and open the door B. Closing from the inside To unlock door A ➥ 1.32. Partially close door B, then slam it shut. Manual locking/unlocking Then repeat this with door A.
Page 45: Tailgate
TAILGATE – in hands-free mode by pressing the 1 button. To open With the tailgate unlocked, press the button 2 and lift the tailgate. Vehicles with a remote To close control Lower the tailgate, initially using the in- terior handle 3 to assist you. The tailgate is locked and unlocked by pressing the remote control button.
Page 46 CENTRAL LOCKING, UNLOCKING OF OPENING ELEMENTS (1/2) Locking the opening elements without the card or the key For example, in the event of a dis- charged battery or the card or key tem- porarily not working etc. With the engine off, the rear doors closed and a front door open, press switch 1 for more than five seconds.
Page 47 CENTRAL LOCKING, UNLOCKING OF OPENING ELEMENTS (2/2) Locking the doors with the tailgate open To lock the vehicle with the boot open (e.g. when transporting something in the boot which prevents it from being closed), or when the vehicle is located in a zone of high electromagnetic radia- tion, or if the card or key is faulty: with Driver’s responsibility...
Page 48 MANUAL DOOR LOCKING, UNLOCKING (1/4) If the remote control or, depending on the vehicle, the card does not work In some cases, the radio frequency remote control or the card may not work: – card or radio frequency remote con- trol battery worn or run flat, vehicle battery flat etc;...
Page 49 MANUAL DOOR LOCKING, UNLOCKING (2/4) Using the key integrated in Vehicles with key/remote the card control Insert the key 2 into the driver’s door Using the key lock 3 to lock or unlock. Insert the key 4 into the driver’s door Once you are inside the vehicle, put the lock to lock or unlock.
Page 50 MANUAL DOOR LOCKING, UNLOCKING (3/4) Locking the doors manually Interior locking/unlocking door control Turn screw 5 with the door open (using the end of the key) and close the door. Switch 6 simultaneously controls the doors and the tailgate. This means that the doors are then locked from the outside.
Page 51 MANUAL DOOR LOCKING, UNLOCKING (4/4) Door and tailgate status Locking the opening indicator elements without the card or the key When the ignition is on, the 6 switch warning light indicates the locking For example, in the event of a dis- status of the opening elements: charged battery or the card or key tem- porarily not working etc.
Page 52: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Operating faults NB: if a door is opened or closed, it will automatically lock again when the If you experience an operating fault vehicle reaches a speed of 6 mph (10 (no central locking, the indicator light 1 km/h).
Page 53 FRONT HEADRESTS To raise the headrest Raise the headrest to its highest po- sition (tilt the seatback if necessary). Press button 1 and lift the headrest to release it. To refit the headrest Insert the headrest rods into the holes (tilt the seatback if necessary).
Page 54 FRONT SEATS (1/2) To store away the armrest Lift the armrest to the storage posi- tion A. Check that it is correctly locked. Heated seats With the ignition on, press switch 2. The integrated indicator comes on. The system, which has a thermostat, decides whether or not the heating is needed.
Page 55 FRONT SEATS (2/2) To reposition the central passenger seat Make sure that nothing prevents the seat from moving. – Activate control 7 to unlock the seat- back; – Lift the seat back; – Make sure the seat is correctly locked in position. Central passenger seat table formation Make sure that nothing prevents the...
Page 56: Steering Wheel/Power-Assisted Steering
STEERING WHEEL/POWER-ASSISTED STEERING Power Assisted Steering Never drive with an inadequately charged battery. Variable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases...
Page 57: Seat Belts
SEAT BELTS (1/6) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants to adjust their seat belts to ensure comply with the legislation of the par- ticular country you are in.
Page 58 SEAT BELTS (2/6) Depending on the vehicle, if the seat is occupied and one of these seat belts is not fastened or becomes unfastened while the vehicle is moving at a speed over approximately 12 mph (20 km/h), ß warning light flashes and a beep sounds for approximately 120 seconds.
Page 59 SEAT BELTS (3/6) Understanding the graphic 7: – white symbol: seatbelt fastened; – black symbol: seatbelt unfastened. When the vehicle speed is below ap- proximately 12 mph (20 km/h), the graphic 7 appears during approximately 60 seconds every time one of the rear seat belts is fastened or unfastened.
Page 60 SEAT BELTS (4/6) Adjusting the height of the Rear side seat belts Conditions of use front seat belts Before using the rear side seat belts, – For the first row of rear seats, it is make sure that for each one, the mandatory to use seat belts 10;...
Page 61 SEAT BELTS (5/6) Centre seat belts Access to the last row To facilitate access to the last row of Unwind the seat belt slowly until the seats, detach the second row seat belt buckle locks in catch 16. by unlocking it from its catch 15. Insert the detached part of the seat belt into the small bar on the fixed part of the belt.
Page 62 SEAT BELTS (6/6) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 63 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/6) Depending on the vehicle, they may – Have the entire restraint comprise: system checked following – front seat belt inertia reel preten- an accident. sioners; – No operation whatso- –...
Page 64 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/6) Load limiter Each airbag system consists of: – an airbag and gas generator fitted on Above a certain severity of impact, this the steering wheel for the driver and mechanism is used to limit the force of in the dashboard for the passenger;...
Page 65 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/6) Operating faults Operation å This system is only operational when Warning light 4 will light up on the ignition is switched on. the instrument panel when the ignition In a severe frontal impact, the airbags is turned on and then go out after a few inflate rapidly, cushioning the impact seconds.
Page 66 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/6) The following conditions will trigger In the event of a frontal impact with In a side impact with another vehicle the pretensioners or airbags. another vehicle of an equivalent or of an equivalent or higher category, at higher category, with an impact area an impact speed equal to or greater...
Page 67 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/6) In the following examples, the pre- In the following examples, there is a – side impact to the front or rear of the tensioners or the airbags could op- risk that pretensioners orairbags may vehicle;...
Page 68 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (6/6) All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s airbag –...
Page 69 METHODS OF RESTRAINT IN ADDITION TO REAR SEAT BELTS Force limiter Above a certain level of impact force, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 70 SIDE PROTECTION DEVICES Side Airbags These airbags may be fitted to individ- ual seats and are deployed at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain Airbags These are airbags fitted to each upper side of the vehicle.
Page 71: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt.
Page 72: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. Driver’s responsibility A child is not a miniature adult.
Page 73 CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to re- strain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact.
Page 74 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier Up to 18 kg or 4 years, the child may From 15 kg or 4 years, the child can than that of an adult and its neck is very travel on a forward-facing seat.
Page 75 CHILD SAFETY: choosing a child, baby seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Do not use the child seat seats: via the seat belt or using the system if it may unfasten the seat ISOFIX system.
Page 76 CHILD SAFETY: choosing a child, baby seat mounting (2/2) – Place the headrest in the top position or remove it; – pass the belt 2 (supplied with the seat) between the two rear headrest rods; – the hook 3 must be attached to the ...
Page 77: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, when this child seats. The diagram on the follow- is possible, you can move the vehi- The laws concerning children travel- ing page shows you how to attach a cle seat forward if necessary (so as to...
Page 78 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat Rear centre seat A carrycot can be installed across the Check that the belt is suitable for secu- vehicle and will take up at least two ring your child seat.
Page 79 CHILD SEATS: attachment by seat belt (1/14) ³ 2-seater van Check the status of the airbag before fitting a child seat or al- lowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬...
Page 80 CHILD SEATS: attachment by seat belt (2/14) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Two or three-seater van versions Front passenger seat(s) With two-seater bench seat Type of child seat Weight of the child With single...
Page 81 CHILD SEATS: attachment by seat belt (3/14) ³ 5-seater Combi Check the status of the airbag before fitting a child seat or al- lowing a passenger to use the seat. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal”...
Page 82 CHILD SEATS: attachment by seat belt (4/14) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. 5-seater Combi version Front passenger Rear side Rear centre Type of child seat Weight of the child seat seat...
Page 83 CHILD SEATS: attachment by seat belt (5/14) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 84 CHILD SEATS: attachment by seat belt (6/14) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. 6-seater Combi version Front seat Rear seat Type of child seat Weight of the child Central Side...
Page 85 CHILD SEATS: attachment by seat belt (7/14) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 86 CHILD SEATS: attachment by seat belt (8/14) ³ 6-seater Combi Check the status of the airbag before fitting a child seat or al- lowing a passenger to use the seat. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal”...
Page 87 CHILD SEATS: attachment by seat belt (9/14) ³ 8-seater combi/bus Check the status of the airbag before fitting a child seat or al- lowing a passenger to use the seat. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal”...
Page 88 CHILD SEATS: attachment by seat belt (10/14) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. 8-seater Bus/Combi version Rear seat Front Weight of Type of child seat passenger 2nd row 2nd row...
Page 89 CHILD SEATS: attachment by seat belt (11/14) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 90 CHILD SEATS: attachment by seat belt (12/14) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. 9-seater Bus/Combi version Front seat Rear seat Weight of 3rd row Type of child seat Central Side...
Page 91 CHILD SEATS: attachment by seat belt (13/14) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 92 CHILD SEATS: attachment by seat belt (14/14) ³ 9-seater combi/bus Check the status of the airbag before fitting a child seat or al- lowing a passenger to use the seat. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal”...
Page 93 CHILD SEATS: attachment using the ISOFIX system (1/12) 5-seater Combi Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
Page 94 CHILD SEATS: attachment using the ISOFIX system (2/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. 5-seater Combi version Seat size ISOFIX Front Rear side Rear centre Type of child seat Weight of the child...
Page 95 CHILD SEATS: attachment using the ISOFIX system (3/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. (1) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 96 CHILD SEATS: attachment using the ISOFIX system (4/12) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. 6-seater Combi version Front seat Rear seat Seat size Weight of ISOFIX Type of child seat...
Page 97 CHILD SEATS: attachment using the ISOFIX system (5/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. (1) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 98 CHILD SEATS: attachment using the ISOFIX system (6/12) 6-seater Combi Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
Page 99 CHILD SEATS: attachment using the ISOFIX system (7/12) 8-seater combi/bus Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
Page 100 CHILD SEATS: attachment using the ISOFIX system (8/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. 8-seater Bus/Combi version Rear seat Seat size Front Weight of ISOFIX Type of child seat passenger...
Page 101 CHILD SEATS: attachment using the ISOFIX system (9/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. (1) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 102 CHILD SEATS: attachment using the ISOFIX system (10/12) The table below summarises the information already shown on the diagram on the following pages, to ensure the ap- plicable regulations are respected. 9-seater Bus/Combi version Front seat Rear seat Seat size Type of Weight of 3rd row...
Page 103 CHILD SEATS: attachment using the ISOFIX system (11/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. (1) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 104 CHILD SEATS: attachment using the ISOFIX system (12/12) 9-seater combi/bus Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
Page 105: Child Safety: Deactivating, Activating The Front Passenger Airbag
CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3) DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat, NEVER fit a rear-facing child re- straint system in a seat protected by an ACTIVATED front AIRBAG.
Page 106 CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (example: label shown above) remind you of these instruc- tions. DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat,...
Page 107 CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
Page 108: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1.94...
Page 109 DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vents. 10 Touch screen or radio or upper cen- 20 Engine start/stop button. tral storage compartment. 2 Location for ashtray or cup holder. 21 Ignition switch for vehicles with key.
Page 110 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1.96...
Page 111 DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vents. 11 Stalk: 19 Engine start/stop button. – the windscreen and rear screen 2 Location for cup holders. 20 Handbrake. washers/wipers; 3 Passenger airbag location.
Page 112: Rear View Mirrors
REAR VIEW MIRRORS (1/2) Heated door mirrors Folding door mirrors The door mirrors automatically fold out Depending on the vehicle, with the when the vehicle is unlocked (switch 3 engine running, the mirrors are heated in position B). The door mirrors fold in in conjunction with the rear windows.
Page 113 REAR VIEW MIRRORS (2/2) Interior rear view mirror Wide angle rear view mirror 6 The various zones seen by the driver are: (depending on the vehicle) Its position can be adjusted. – D in the the wide-angle rear view Lower the sun visor 5 to access the Rear view mirror with lever 4 mirror;...
Page 114: Warning Lights
WARNING LIGHTS (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. In some cases, the appearance of a warning light is accompanied by a mes- sage. š Side light warning light á Main beam headlight tell- tale Dipped beam headlight tell- tale...
Page 115 WARNING LIGHTS (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Low fuel level warning light Handbrake on and brake cir- cuit incident warning light This lights up when the ignition is switched on and goes out after a few This comes on when the ignition is seconds.
Page 116 WARNING LIGHTS (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. À Ä Oil pressure warning light Toxic Fume Filter System Warning Light This lights up when the ignition is switched on and goes out after a few For vehicles equipped with this option, seconds.
Page 117 WARNING LIGHTS (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.   Particle filter system warn- Engine standby warning ing light ➥ 2.12 light ➥ 2.8   Warning light for reagent Unavailability of engine level and faults in the ex- standby warning light ➥...
Page 118 WARNING LIGHTS (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Š‰ Gear change indicators This lights up to advise you to change to a higher gear (arrow pointing upwards) or lower gear (arrow pointing downwards) ➥...
Page 119 DISPLAYS AND INDICATORS (1/4) Engine oil level low warning Instrument panel A Rev counter 5 (graduations x 1000) When the engine is started, the instru- It lights up when the ignition is switched ment panel display alerts you if the min- on.
Page 120 DISPLAYS AND INDICATORS (2/4) Speedometer 9 Automatic gearbox display 7 ➥ 2.99 (km or miles per hour) Fuel gauge 8 Control your speed according to the ap- The number of squares lit shows the proved speedometer only 9. fuel level. When it is at minimum, the The indicator 6 is provided as an indi- squares disappear and the low fuel cation.
Page 121 DISPLAYS AND INDICATORS (3/4) Instrument panel B Vehicles not fitted with a multimedia Rev counter 11 screen (graduations x 1000) It lights up when the ignition is switched – With the ignition off, press the 2 on. In some cases, the appearance of a Coolant temperature indicator 12 switch as many times as required to warning light is accompanied by a mes-...
Page 122 DISPLAYS AND INDICATORS (4/4) Speedometer 18 Trip computer 14 ➥ 1.109 Driving style indicator 17 ➥ 2.18 Fuel gauge 19 Estimated mileage with remaining Overspeed buzzer fuel 15 If the level is at the minimum, warn- Depending on the vehicle and coun- ...
Page 123 ON-BOARD COMPUTER: general information (1/2) Vehicle fitted with trip computer 1 Press the switch 2 as many times as re- quired to reach the “Vehicle” tab. Repeatedly press the 3 or 4 switches. Selections (the display depends on the vehicle equipment and country) a) Trip log, operating faults and infor- mation message readout;...
Page 124 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption, range and average speed will become more stable and reliable the further you travel after pressing the reset button. For the first few miles after pressing the reset key you will notice that the range increases as you travel.
Page 125 ON-BOARD COMPUTER: trip settings (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. FUEL USED b) Journey parameters. Fuel used.
Page 126 ON-BOARD COMPUTER: trip settings (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected RANGE e) Estimated range with remaining fuel. 541 km The value is displayed after driving 400 metres. DISTANCE 522 km f) Distance travelled since last reset.
Page 127 ON-BOARD COMPUTER: trip settings (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) h) Mileage before service With the ignition switched on and the engine not running, OIL CHANGE IN when the message “Service Intervals”...
Page 128 ON-BOARD COMPUTER: trip settings (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected TYRE PRESSURE SET i) Tyre pressure reset ➥ 2.26. <PRESS-HOLD> SPEED LIMITER 90 km/h j) Cruise control, speed limiter programmed speed ➥ 2.63 and ➥ 2.67. CRUISE CONTROL 90 km/h k) Time and temperature ➥...
Page 129: Trip Computer
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
Page 130 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 131 TRIP COMPUTER: warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Call an approved Dealer. Some examples of warning messages are given below. Note: the messages appear on the display either individually or alter- nately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Page 132 CLOCK AND EXTERIOR TEMPERATURE (1/2) Vehicles fitted with a multimedia Vehicles not fitted with a multimedia Set the hour using control 3 or 4, then screen screen press switch 5 “OK” to confirm. The time and exterior temperature are Press the switch 2 as many times as re- Set the minutes using control 3 or 4, displayed on the multimedia screen 1.
Page 133 CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator Special note: When the external temperature is be- tween -3°C and +3°C, the °C symbols flash (indicates risk of ice). External temperature in- dicator As ice formation is related Depending on the vehicle, If the to climatic exposure, local electrical supply is cut (battery dis- air humidity and temperature, the...
Page 134: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/6) š Side lights Dipped beam headlights Turn ring 2 until the symbol is opposite mark 3. Manual operation This indicator light on the instrument Turn ring 2 until the symbol is opposite panel comes on. mark 3.
Page 135 EXTERIOR LIGHTING AND SIGNALS (2/6) During deactivation of the main beam The main beam headlights come on au- headlights, the dipped beam headlights tomatically if: return to their original position. – exterior light is weak; – no other vehicles or lighting are de- tected;...
Page 136 EXTERIOR LIGHTING AND SIGNALS (3/6) Operating faults When the message “Check Automatic Lighting” appears on the instrument panel, the system is deactivated. Consult an approved dealer. Using the portable naviga- tion system at night in the windscreen area below the camera may disturb the op- eration of the “automatic main beam headlights”...
Page 137 EXTERIOR LIGHTING AND SIGNALS (4/6) Lights-on reminder buzzer Welcome and goodbye function If the lights are on after the engine is (depending on the vehicle) switched off, a warning beep sounds when the driver’s door is opened to Once the function is activated, the day- warn you that the lights are still on (to time running lights and the rear side avoid battery discharge or other prob-...
Page 138 EXTERIOR LIGHTING AND SIGNALS (5/6) With the engine lights switched off, the 2 ring in AUTO, pull the lever 1 to- wards you: the side lights and dipped beam headlights will switch on for ap- proximately 30 seconds along with the š...
Page 139 EXTERIOR LIGHTING AND SIGNALS (6/6) Rear fog lights Cornering lights  (depending on vehicle) Turn centre ring 4 on the stalk until the symbol faces mark 3, then re- When driving in forward gear, with lease it. the vehicle speed below approxi- mately 25 mph (40 km/h), whenever Operation of the fog lights depends on the dipped beam headlights are on:...
Page 140: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT Load status Control position Driver only or with passenger All seats occupied Driver with passengers and luggage (or load) reaching the maximum permissible all-up weight Driver without a passenger and with luggage (or load) reaching the 3 or 4 maximum authorised load weight On vehicles fitted with this function, control A allows you to adjust the height...
Page 141: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode Briefly shift the stalk 1 upwards or downwards, not exceeding the point of resistance, then release it: the stalk will return to its original position and the direction indicator light concerned will flash three times.
Page 142 WINDSCREEN WASH, WIPE (1/4) Special note When driving, the wiping speed slows down whenever the vehicle stops. For example, fast wiping speed will slow to normal wiping speed. As soon as the vehicle moves off, wiping will return to the speed originally selected.
Page 143 WINDSCREEN WASH, WIPE (2/4) Note: – the rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers. In foggy weather or during snowfalls, wiping is not au- tomatically triggered and remains under the driver’s control;...
Page 144 WINDSCREEN WASH, WIPE (3/4) – D slow continuous wiping. Operating faults – E fast wiping speed. In the event of a malfunction of the au- tomatic wiping, the wiper is set to inter- Note: there is a maintenance position mittent wiping. Call an approved Dealer. for replacing wiper blades.
Page 145 WINDSCREEN WASH, WIPE (4/4) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blade and the screen regularly with soapy water; – do not use it when the screen is dry; –...
Page 146 REAR SCREEN WASHER, WIPER (1/2) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blade and the screen regularly with soapy water; – do not use it when the screen is dry;...
Page 147 REAR SCREEN WASHER, WIPER (2/2) Activation/Deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. Engaging reverse gear triggers inter- mittent wiping (if the front wipers are in If an obstacle prevents the blade from operation).
Page 148 TANK (1/3) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). To fill up with fuel, the Keep the nozzle in this position through- engine must be stopped out the entire filling operation.
Page 149 TANK (2/3) Running out of fuel on diesel versions Vehicles with key/remote control – Set the ignition key to “On” posi- tion M ➥ 2.2 and wait a few minutes before starting to enable the fuel cir- Please note when work- cuit to be primed;...
Page 150 TANK (3/3) Vehicles with card Persistent fuel odour With the card in the passenger com- If you notice a persistent partment, press the start button 3 with- fuel odour you should: out pressing any of the pedals. Wait a few minutes before starting. This will –...
Page 151: Reagent Tank
REAGENT TANK (1/4) Please ensure that you comply with the legislation of your country. It is important to remember that failure to respect regulations in force could lead to legal action being taken against the vehicle owner. To fill up with reagent, the engine must be stopped (not just on standby Operating principle in the case of vehicles with the Stop...
Page 152 REAGENT TANK (2/4) Precautions for use Special cases The reagent fluid freezes below ap- The tank can be filled at the pump. In proximately -10°C. other cases, it is essential to read the information shown on the reagent con- In these conditions, do not attempt filling tainer (e.g.
Page 153 REAGENT TANK (3/4) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Messages What to do? When the message is displayed when the ignition is switched on, you have less than 1,488 miles (2,400 km) range. –...
Page 154 REAGENT TANK (4/4) System faults When the indicator lights light up, this may be accompanied by a beep. Indicator lights Messages What to do? “Check Anti- Pollution System”  Indicates a fault in the system. Contact your approved “AdBlue quality to check” a n d Dealer as soon as possible.
Page 155 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Ignition switch .
Page 156: Running In
RUNNING IN, IGNITION SWITCH: vehicle with key Diesel version “Ignition” position ON 2 For the first 932 miles (1,500 km), do The ignition is switched on: Any acces- not exceed 80 mph (130 km/h) in the sories (radio etc.) can be used. highest gear, or 2,500 rpm.
Page 157: Starting/Stopping The Engine: Vehicle With Key
STARTING, STOPPING THE ENGINE: vehicle with key Stopping the engine For all vehicles: turn the key to the “START” position 3 With the engine idling, turn the key without depressing the accelerator back to the “LOCK” position 0. pedal. Release the key as soon as the engine starts.
Page 158: Starting, Stopping The Engine: Vehicle With Card
STARTING, STOPPING THE ENGINE: vehicle with card (1/4) The card must be in detection zone 1 To start: for the van version, and in detection – vehicles with an automatic gearbox, zone 2 for the combi version. place the lever in position P or N, de- Press the button 3.
Page 159 STARTING, STOPPING THE ENGINE: vehicle with card (2/4) Special note: – if one of the starting conditions is not met, the message “Press Brake + START”, “Press Clutch + Start” or “Select Gearbox Position “P”” is dis- played on the instrument panel; –...
Page 160 STARTING, STOPPING THE ENGINE: vehicle with card (3/4) Conditions for stopping the If the card is no longer in the passen- ger compartment or if the card’s bat- engine tery is flat, when the vehicle is station- The vehicle must be at a standstill. ary and you try to switch the engine off, the message “Keycard absent: press/ The vehicle must be stationary, with the...
Page 161 STARTING, STOPPING THE ENGINE: vehicle with card (4/4) The message “Place card on zone + When you leave your vehi- START” appears on the instrument cle, especially if you have panel. your card with you, check Press the brake or clutch pedal, then that the engine is com- place the card 5 (button side facing pletely switched off.
Page 162 FUNCTION STOP AND START (1/4) This system enables a reduced fuel For all vehicles:  consumption and lower greenhouse – the speed is zero. The warning light on the instru- gas emissions. The engine remains on standby if posi- ment panel is lit when the engine is on The system is activated automati- tion P is selected, or if position N is se- standby.
Page 163 FUNCTION STOP AND START (2/4) Preventing the engine from Conditions for coming out of – the gearbox is in neutral and the clutch pedal is slightly depressed; standing by engine standby – the engine is in gear and the clutch In certain situations, such as negotiat- For automatic gearboxes: pedal is pressed right down.
Page 164 FUNCTION STOP AND START (3/4) Conditions preventing the – the gradient is too steep for vehicles  fitted with an automatic gearbox; standby of the engine Depending on the vehicle, the warning light appears on the instrument – the “Clear view” function is activated Certain conditions prevent the system panel to indicate that engine standby ➥...
Page 165 FUNCTION STOP AND START (4/4) Deactivating, activating the Special feature of the automatic engine re-start function Under certain conditions, the engine Press 1 to deactivate the function. The can restart on its own in order to guar- message “Stop & Start deactivated” will antee your safety and comfort.
Page 166: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS (1/5) Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of –...
Page 167 SPECIAL FEATURES OF DIESEL VERSIONS (2/5)  Particle filter The display of the warning light The particle filter is used in the treat- on the instrument panel may be accom- ment of exhaust gases from diesel en- panied by an increase in engine speed gines.
Page 168 SPECIAL FEATURES OF DIESEL VERSIONS (3/5) Manual regeneration of the particle – go to the “Vehicle” tab in the instru- filter leads to high temperature in the ment panel menu ➥ 1.109; exhaust system and exhaust gases. – press the 3 or 4 buttons repeatedly Precautions must be taken into account until the “Regenerate DPF [long (see below and on the following page)
Page 169 SPECIAL FEATURES OF DIESEL VERSIONS (4/5) Note: do not start the regeneration in During the regeneration process: If you need to interrupt the particle the event of an insufficient oil or coolant filter regeneration, press one of the – the engine speed first increases to À...
Page 170 SPECIAL FEATURES OF DIESEL VERSIONS (5/5) Special cases If the filter becomes excessively sat- © urated, the warning light and,  depending on the vehicle, the warning light will appear on the instru- ment panel, accompanied by the mes- sage “Check injection”. In this case, please consult an Authorised Dealer.
Page 171: Gear Lever/Handbrake
GEAR LEVER/HANDBRAKE The reversing lights will come on as soon as reverse gear is selected (with When stationary and de- the ignition on). pending on the slope and/or Vehicles fitted with parking distance vehicle load, it may be nec- control ➥ 2.88. essary to pull up the hand- brake at least two extra notches and engage a gear (1...
Page 172: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/6) Fuel consumption is accredited in ac- Depending on the vehicle, you will have “Free-wheel” function cordance with a standard regulatory various functions which enable you to Depending on the vehicle, on vehi- method. Identical for all manufactu- lower your fuel consumption: cles fitted with an automatic gearbox rers, this enables vehicles to be com-...
Page 173 DRIVING ADVICE, ECO-DRIVING (2/6) Driving advice and ECO driving If your vehicle is equipped and if driving under-load, the “Performance mode” function enables you to limit under-rev- ving, gives priority to engine braking when decelerating and enables more dynamic engine driving. Note: performance mode is only availa- ble for vehicles fitted with an automatic gearbox ➥...
Page 174 DRIVING ADVICE, ECO-DRIVING (3/6) Gear change indicator 3 Driving style indicator 4 Depending on the vehicle, to obtain op- Informs you about the driving style timum consumption levels, a warning adopted in real time. You will be notified light on the instrument panel lets you by the size of the 4 indicator light.
Page 175 DRIVING ADVICE, ECO-DRIVING (4/6) Disabling the function Press the 5 switch as many times as necessary to return to normal mode.  Warning light 6 goes out on the in- strument panel to confirm deactivation. Note: on vehicles equipped with an au- tomatic gearbox, each time the engine is switched off ECO mode will be deac- tivated and it will be necessary to acti-...
Page 176 DRIVING ADVICE, ECO-DRIVING (5/6) – High speeds significantly affect – Double declutching and accelerating the vehicle’s fuel consumption. before switching off are unnecessary Examples (at a steady speed): in modern vehicles. – reducing the speed from 80 mph – Bad weather, flooded roads: (130 km/h) to 68 mph (110 km/h) Do not drive through approximately saves up to 20% of...
Page 177 DRIVING ADVICE, ECO-DRIVING (6/6) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 178: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that failure to end of their service life, which entered respect antipollution regulations could The exhaust gas monitoring system will into force in 2015.
Page 179: Environment
ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to its entire service life: during production, centres to ensure that it is recycled.
Page 180 TYRE PRESSURE MONITOR (1/5) Resetting the standard level for the tyre pressures This should be performed: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended);...
Page 181 TYRE PRESSURE MONITOR (2/5) – press and hold (around 3 seconds) the button 4 to launch the reset. The flashing tyres followed by the mes- sages “Learning Tyre Pressures” and then “Tyres location in progress” indicates that the reset request for the tyre pressure reference value has been acknowledged.
Page 182 TYRE PRESSURE MONITOR (3/5) The table below shows the possible messages related to the tyre resetting procedure. Steps Displays Messages Readings (depending on the vehicle) With the ignition on and the vehicle stationary, start the resetting the pressure of all four tyres by pressing and holding the 4 OK switch.
Page 183 TYRE PRESSURE MONITOR (4/5) Readjustment of tyre Emergency spare wheel pressures If the vehicle is equipped with an emer- gency spare wheel, it will not have a The pressure of the four tyres must sensor. be set when cold (refer to the label lo- cated on the edge of the driver’s door).
Page 184 TYRE PRESSURE MONITOR (5/5) The information on the instrument panel signals any potential tyre pressure faults (e.g. deflated or punctured tyre). For ® your safety, the warning light requires you to stop immediately as soon as traffic conditions allow. Indicator Messages Displays Readings...
Page 185 DRIVING CORRECTION DEVICES AND AIDS (1/5) Anti-lock braking system Depending on the vehicle, this is com- Operating faults: posed of: (ABS) © – lit up on the in- – anti-lock braking system (ABS); strument panel accompanied Under heavy braking, the ABS prevents by the messages “Check ABS”, the wheels from locking, allowing the –...
Page 186 DRIVING CORRECTION DEVICES AND AIDS (2/5) Electronic stability program Understeer control Operating faults (ESC) with understeer control This system optimises the action of the When the system detects an operating and traction control ESC in the case of pronounced under- fault the message “Check ESC”...
Page 187 DRIVING CORRECTION DEVICES AND AIDS (3/5) Driver assistance with a Emergency brake assist Braking anticipation trailer Depending on the vehicle, when you This system supplements the ABS This system helps to maintain control rapidly release the accelerator, the and helps reduce vehicle stopping dis- over the vehicle while using a trailer.
Page 188: Driver Correction Devices And Aids
DRIVER CORRECTION DEVICES AND AIDS (4/5) Grip control “Soft ground” mode Press the switch 1: the message “Grip If fitted on the vehicle, grip control Extend Loose Surface ON” is displayed makes it easier to control the vehicle on  low grip surfaces (soft ground, etc.).
Page 189 DRIVING CORRECTION DEVICES AND AIDS (5/5) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards, de- The hill start assistance pending on the slope, by automatically system cannot completely applying the brakes when the driver lifts prevent the vehicle from...
Page 190: Lane Departure Warning
LANE DEPARTURE WARNING (1/5) Location of the camera 1 Make sure the windscreen is not ob- scured (dirt, mud, snow, condensation etc.). Using information from the 1 camera, the function warns the driver when a continuous or broken line is crossed or when approaching the roadside (di- vider, barrier, pavement, embankment, etc.) without the direction indicator...
Page 191 LANE DEPARTURE WARNING (2/5) To deactivate the function, press the switch 2 to select “Lane departure warning off” on the instrument panel.  Warning light goes out on the in- strument panel. Operation When the function is activated, the  warning light and the left and right lines 3 are displayed in grey on the instrument panel.
Page 192 LANE DEPARTURE WARNING (3/5) Temporarily not available Conditions for non-activation of the system – Very fast lane departure; The system cannot be activated when: – driving continuously on a line; – reverse gear is engaged; – four seconds approximately after changing lanes;...
Page 193 LANE DEPARTURE WARNING (4/5) Operating faults – press the 6 or 7 control repeatedly to reach the “DRIVING ASSIST” menu. In the event of a malfunction, the left Press the switch 8 OK; and right line indicators (and, depend-  –...
Page 194 LANE DEPARTURE WARNING (5/5) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs –...
Page 195: Blind Spot Warning
BLIND SPOT WARNING (1/6) Special feature Using information from the ultrasonic sensors fitted on each side of the Ensure that the ultrasonic sensor bumpers (zone B), the system notifies zones B and C on each side of the the driver when another vehicle ap- bumpers are not obscured (by dirt, pears in the detection zone A.
Page 196 BLIND SPOT WARNING (2/6) – press the switch 5 OK again to acti- vate or deactivate the function: function activated < function deactivated Activation/deactivation – press the 3 or 4 control repeatedly to reach the “Settings” menu. Press the Vehicles fitted with a multimedia switch 5 OK;...
Page 197 BLIND SPOT WARNING (3/6) Operating faults If the system detects a fault, the mes- sage “Check Side radars” is displayed on the instrument panel. Consult an ap- proved dealer. Indicator 6 Operation An indicator light 6 is located on each The function alerts you if your vehicle rear view mirror 7.
Page 198 BLIND SPOT WARNING (4/6) Display E Direction indicator activated, the 6 warning light flashes when the func- tion detects a vehicle in the blind spot warning area and/or a vehicle is rapidly approaching from the rear on the side towards which you will turn the wheel. If you cancel the direction indicator, the function will return to the initial warning When the engine is started, the...
Page 199 BLIND SPOT WARNING (5/6) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
Page 200 BLIND SPOT WARNING (6/6) Limitation of the system operation – The ultrasonic detection zones should be kept clean and free of any modifications in order to ensure the proper op- eration of the system. – Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system. –...
Page 201 SAFE DISTANCE WARNING (1/4) The function is activated when the vehi- cle speed is between about 19 and 124 mph (30 and 200 km/h). Location of the camera 1 Make sure the windscreen is not ob- scured (by dirt, mud, snow, condensa- tion etc.).
Page 202 SAFE DISTANCE WARNING (2/4) – press the 5 or 6 control repeatedly to reach the “Distance warning” menu. Press the switch 7 OK; – press the switch 7 OK again to acti- vate or deactivate the function: function activated < function deactivated Activating/deactivating the Vehicles not fitted with a multimedia...
Page 203 SAFE DISTANCE WARNING (3/4) – C (orange): the time interval falls be- tween around 1 and 2 seconds (in- sufficient distance between the two vehicles); – D (red): the time interval is less than or equal to around one second (very insufficient distance between the two The measurement is dis- vehicles).
Page 204 SAFE DISTANCE WARNING (4/4) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs –...
Page 205: Active Emergency Braking
ACTIVE EMERGENCY BRAKING (1/6) Depending on the reactivity of the driver, the system can assist with brak- ing in order to limit damage or prevent a collision. Note: ensure that the windscreen and front bumper are not obstructed (by dirt, mud, snow, condensation, number plate, etc.).
Page 206 ACTIVE EMERGENCY BRAKING (2/6) Operation Special features of warnings Depending on the speed, the warning Detection of vehicles and braking may be activated simulta- When driving, in the event of a risk of neously. collision with the vehicle in front the Special features of stationary system will: vehicles...
Page 207 ACTIVE EMERGENCY BRAKING (3/6) – press the 6 or 7 control repeatedly to reach the “Active braking” menu and press the 8 OK switch. Press the switch 8 OK again to activate or deactivate the function: function activated < function deactivated ...
Page 208 ACTIVE EMERGENCY BRAKING (4/6) Temporarily not available Operating faults  If the system detects a temporary fault, ©  illuminated on the in- warning light appears on the strument panel: this indicates that the instrument panel. system has detected an operating fault. Consult an approved dealer.
Page 209 ACTIVE EMERGENCY BRAKING (5/6) Active emergency braking This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steer- ing wheel, pedals etc.).
Page 210 ACTIVE EMERGENCY BRAKING (6/6) Limitation of the system operation – Each time the vehicle is started, the system carries out a calibration according to the vehicle surroundings and may be inactive for a length of time between approximately two to five minutes. –...
Page 211 FATIGUE DETECTION WARNING (1/2) The fatigue detection warning is a func- tion which is useful on monotonous roads (motorways, high-speed roads etc.). It analyses driver behaviour and takes account of events to inform you of any risk of fatigue such as: –...
Page 212 FATIGUE DETECTION WARNING (2/2) – repeatedly press the control 3 up or When a risk of fatigue is detected, down until you reach the Fatigue de- the message “Fatigue warning have a tection warning menu, then press the break” is displayed on the instrument switch 2 OK .
Page 213: Detection Of Road Signs
DETECTION OF ROAD SIGNS (1/4) Note: make sure the windscreen is not For vehicles equipped with a navigation obscured (dirt, mud, snow, condensa- system and if the vehicle is travelling in tion etc.). a country where the speed units differ from those of the vehicle, the system For vehicles which are equipped with it, displays the speed limit sign in the unit...
Page 214 DETECTION OF ROAD SIGNS (2/4) – press the 4 or 5 control repeatedly to reach the “Settings” menu and press 6 OK; – press the 4 or 5 control repeatedly to reach the “DRIVING ASSIST” menu and press 6 OK; –...
Page 215 DETECTION OF ROAD SIGNS (3/4) If the speed limit is exceeded, the circle around the panel flashes (7 warning light) along with a sound signal to warn the driver. Operation Varying the limit speed If the speed limit notification differs from Warning lights the detected speed value, press and The function displays the following...
Page 216 DETECTION OF ROAD SIGNS (4/4) Operating faults The system cannot detect the speed limit if: – the windscreen is not clean; – the camera is blinded by the sun; – there is insufficient visibility (night, fog etc.); – the signs are not legible (snow, etc.) or are hidden (by another vehicle or by trees);...
Page 217: Speed Limiter
SPEED LIMITER (1/4) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. The speed limiter is linked with the “Hill Descent Control” function, enabling use of the braking system to optimise down- hill speed limitation.
Page 218 SPEED LIMITER (2/4) Driving Switching on To store the current speed, press the 4 switch (RES/+) or the 3 switch (SET/- When a limit speed has been set but Press the switch 1. The 6 warning light ): the limit speed replaces the dashes not yet reached, driving is similar to appears in grey.
Page 219 SPEED LIMITER (3/4) Exceeding the limit speed It is possible to exceed the limit speed at any time. To do this: press the accel- erator pedal firmly and fully (beyond the resistance point). While the speed is being exceeded, the speed limiter flashes red on the instru- ment panel.
Page 220 SPEED LIMITER (4/4) Putting the function on Switching off the function standby The speed limiter function is inter- rupted: The speed limiter function is suspended when you press switch 5 (0). The limit – when you press the 1 switch. In this speed is stored and displayed in grey case, the speed is no longer stored;...
Page 221: Cruise Control
CRUISE CONTROL (1/5) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 19 mph (30 km/h). The cruise control function is linked with the “Hill Descent Control”...
Page 222 CRUISE CONTROL (2/5) Switching on Activating cruise control Driving Press the switch 1. While the vehicle is moving a steady Once a cruising speed is registered speed above approximately 19 mph and the cruise control function is active, The 6 warning light appears in grey. (30 km/h), press the 2 (SET/-) switch you may lift your foot off the accelera- The “Cruise control ON”...
Page 223 CRUISE CONTROL (3/5) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes in red on the instrument panel. Then, release the accelerator pedal: after a few seconds, the vehicle Temporarily not available will automatically return to its set cruis-...
Page 224 CRUISE CONTROL (4/5) Putting the function on Returning to the cruising speed Note: if the speed previously stored is much higher than the current speed, standby If a speed is stored, it can be recalled, the vehicle will accelerate more rapidly once you are sure that the road condi- The function is set to standby if you: to reach this threshold.
Page 225 CRUISE CONTROL (5/5) Switching off the function Warning light 6 and the message “Cruise control OFF” disappear from The cruise control function is inter- the instrument panel to confirm that the rupted: function has stopped. – when you press the 1 switch. In this case, there is no stored speed;...
Page 226: Adaptive Cruise Control
ADAPTIVE CRUISE CONTROL (1/14) Based on information from a radar or The adaptive cruise control function is Note: camera, the adaptive cruise control available between 18 mph (30 km/h) – the driver must observe the maxi- function gives you the option of main- and 105 mph (170 km/h), depending mum speed limit and safe distances taining a selected speed, known as the...
Page 227 ADAPTIVE CRUISE CONTROL (2/14) Location of the camera 1 Controls Displays Make sure the windscreen is not ob- 3 Safe distance settings Adaptive cruise control warning scured (by dirt, mud, snow, condensa- light. 4 Switch the function to standby (with tion etc.).
Page 228 ADAPTIVE CRUISE CONTROL (3/14) Switching on The cruising speed 11 replaces the dashes and cruise control is confirmed Press switch 5. by the appearance of the cruising speed   Warning light appears in grey, in green and warning light and the message “Adaptive Cruise Ctl If you try to activate the function above ON”...
Page 229 ADAPTIVE CRUISE CONTROL (4/14) Safe distance control activation As soon as cruise control is activated, the default safe distance 10 is displayed in green on the instrument panel. The default safe distance corresponds to approximately two seconds (see follow- ing pages). If the system detects a vehicle in your lane, an outline of a vehicle 9 appears above the distance gauge 10 on the in-...
Page 230 ADAPTIVE CRUISE CONTROL (5/14) – distance gauge B: intermediate dis- Then, release the accelerator pedal: tance 2 (corresponding to approxi- the cruise control and safe distance mately 2 seconds); control will automatically resume the speed and distance instructions that – distance gauge C: intermediate dis- you had previously selected.
Page 231 ADAPTIVE CRUISE CONTROL (6/14) Overtaking manoeuvre – you open one of the opening ele- ments; If you wish to overtake the vehicle in – you press the engine start/stop front, activating the indicator will tem- button; porarily cancel the safe distance con- trol and enable an acceleration speed –...
Page 232 ADAPTIVE CRUISE CONTROL (7/14) Exit from standby Based on the current speed When the cruise control is set to Based on the stored cruising speed standby, pressing switch 6 (SET/-) re- If a speed is stored, it can be recalled, activates the cruise control function once you are sure that the road condi- without taking into account the stored...
Page 233 ADAPTIVE CRUISE CONTROL (8/14) Switching off the function The adaptive cruise control function is deactivated when you press the 6 switch.  The warning light disappears from the instrument panel to confirm that the function is no longer active. Temporary unavailability The radar is able to detect vehicles in front of your vehicle.
Page 234 ADAPTIVE CRUISE CONTROL (9/14) Operating faults Ensure that the radar area is not ob- structed (dirt, mud, snow, a badly If an operating fault is detected on one fitted/attached front number plate), im- or more components of the system, the pacted, modified (including paintwork) adaptive cruise control function is inter- or hidden by any accessory fitted on the...
Page 235 ADAPTIVE CRUISE CONTROL (10/14) Limitations of system The system cannot detect: Detection during cornering operation – vehicles arriving at intersections: slip When entering a corner or bend, the roads (e.g. H) ; radar and/or camera may temporarily Vehicle detection not be able to detect the vehicle in front –...
Page 236 ADAPTIVE CRUISE CONTROL (11/14) Detection of vehicles in adjacent Vehicles hidden due to variations in – vehicles transporting long objects lanes ground relief which exceed the line; The system may detect vehicles driving The system will not detect vehicles – the actual length of tall vehicles on an adjacent lane when: hidden due to variations in ground relief (e.g.
Page 237 ADAPTIVE CRUISE CONTROL (12/14) Stationary and slow moving – vehicles in front12 which change Non-detection of fixed obstacles vehicles lane, revealing a stationary vehi- and objects of a small size cle 13 (e.g. P). The system cannot detect: When your speed is over approximately 31 mph (50 km/h), the system does –...
Page 238 ADAPTIVE CRUISE CONTROL (13/14) This function is an additional driving aid. It can under no circumstances replace the driver’s responsibility to respect speed limits and safe distances and to be vigilant. The driver must always be in control of the vehicle. The driver must always adapt their speed to the surroundings and driving conditions, regardless of system indications.
Page 239 ADAPTIVE CRUISE CONTROL (14/14) In the event of system disturbance Some conditions can disturb or damage the operation of the system, such as: – the windscreen or bumper is obscured in the area of the radar (by dirt, ice, snow, condensation, number plate etc.); –...
Page 240: Overspeed Function
VEHICLE WITH OVERSPEED FUNCTION Special case: if your vehicle is fitted with the Cruise control/Speed limiter, fully pressing the accelerator pedal (beyond the kickdown point) will not enable you to exceed the overspeed function set speed ➥ 2.63. The vehicle speed may be permanently set at a fixed value depending on the vehicle or on local legislation.
Page 241: Fast Idle Speed
FAST IDLE SPEED Switching off the function The function is interrupted when: – you depress the clutch pedal and/or accelerator pedal; – the vehicle speed is above 0 mph; ® – the indicator light is lit up on the instrument panel; ©...
Page 242: Parking Distance Control
PARKING DISTANCE CONTROL (1/8) Depending on the vehicle, the system detects obstacles to the front, the rear and the sides of the vehicle. The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h).
Page 243 PARKING DISTANCE CONTROL (2/8) Note: in the event of a change in tra- jectory during a manoeuvre, the risk of collision with an obstacles may be sig- nalled late. Operation Note: the display 2 shows the vehicle surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are...
Page 244 PARKING DISTANCE CONTROL (3/8) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the D dis- play; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
Page 245 PARKING DISTANCE CONTROL (4/8) Adjustment Depending on the vehicle, with the engine running, some settings can be adjusted from the multimedia screen 4. Please refer to the multimedia instruc- tions for further information. Parking distance control audio volume Adjust the volume of the parking dis- tance control by pressing + or -.
Page 246 PARKING DISTANCE CONTROL (5/8) – press the 8 or 9 control repeatedly to reach the “PARKING ASSIST” menu. Press the switch 10 OK; – select “ON” or “OFF” to activate or deactivate the function. If the 6 button cannot be used to re- activate Park Assist, check that the function has not been deactivated on the instrument panel.
Page 247 PARKING DISTANCE CONTROL (6/8) Deactivating the parking – select “BIP VOLUME” to adjust the volume of the parking distance con- distance control manually trol using the 8 or 9 control. You must disable the function if: – if towing, carrying or trailer equip- Parking distance control ment not recognised by the system automatic deactivation...
Page 248 PARKING DISTANCE CONTROL (7/8) System servicing/repairs – In the event of an impact, the alignment of the sensors may be altered and their operation may consequently be affected. Deactivate the function and consult an authorised dealer. – Any work in the area where the sensors are located (repairs, replacements, etc.) must be carried out by a qualified profes- sional.
Page 249 PARKING DISTANCE CONTROL (8/8) Limitation of the system operation – The area around the sensors must be kept clean and free of any modifications in order to ensure the proper operation of the system. – Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system. –...
Page 250: Reversing Camera
REVERSING CAMERA (1/3) Operation Note: make sure that the reversing Note: depending on the vehicle, you camera is not obscured (by dirt, mud, can adjust certain settings from the When reverse gear is engaged, the snow, condensation, etc.). multimedia display 3. Refer to the camera 1 located on the tailgate or, handbook for the equipment.
Page 251 REVERSING CAMERA (2/3) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately.
Page 252 REVERSING CAMERA (3/3) H J K Difference between the Reversing towards a steep downhill Reversing towards a protruding slope object estimated distance and actual distance The fixed guidelines 6 show the dis- Position H seems further than position J tances as further than they actually are. on the screen.
Page 253 AUTOMATIC TRANSMISSION (1/4) Driving in automatic mode Put lever 1 into position D. In most road conditions you will en- counter, you will not need to touch your lever again: the gears will change au- tomatically at the right time and at the most suitable engine speed because the automatic system takes into ac- count the vehicle load and road contour...
Page 254 AUTOMATIC TRANSMISSION (2/4) Driving in automatic mode – to move up through the gears, push the lever backwards. (cont.) The gear selected is displayed on the Economical driving instrument panel. When driving, always leave the lever in position D, keeping the accelerator Special cases pedal lightly depressed to ensure auto- matic gear changes at a lower engine...
Page 255: Automatic Gearbox
AUTOMATIC TRANSMISSION (3/4) Special circumstances Parking the vehicle Maintenance period Refer to the maintenance document – If the bends and road surface do When the vehicle is stopped, move for your vehicle or consult an Approved not allow you to stay in automatic the lever to position P while keeping Dealer to check whether the automatic mode (e.g.
Page 256 AUTOMATIC TRANSMISSION (4/4) Operating faults – when driving, if the message “Check auto gearbox” appears on the instrument panel, it indicates a failure. Contact your approved Dealer as soon as possible; – when driving, if the message “Gearbox overheating” appears on the instrument panel, stop as soon as possible to let the gearbox cool down and wait for the message to...
Page 257: Emergency Call
EMERGENCY CALL (1/3) If the vehicle is equipped, the emer- gency call function can be used to call the emergency services (without charge) automatically or manually in the event of an accident or illness, re- ducing the time it takes for the emer- gency services to arrive.
Page 258 EMERGENCY CALL (2/3) Automatic mode In the event of unintended operation, it is possible to cancel the call by press- If the automatic mode 2 warning light ing the 3 button for around two sec- appears in green this confirms that the onds, before the call is connected to automatic system is activated.
Page 259 EMERGENCY CALL (3/3) The system operates with a dedi- cated battery. The battery service life is approximately four years (the 1 warning light lights up in red to warn you when approaching expiry). Without the emergency call feature, Consult an approved dealer the system is not trackable and will not be under constant surveillance.
Page 260 2.106...
Page 261 Section 3: Your comfort Air Vents ..............Manual air conditioning, heating system .
Page 262 AIR VENTS, air outlets (1/2) 1 left-hand side window demister 5 right-hand side air vent. vent. 6 right-hand side window demister 2 left-hand side air vent. outlet. 3 windscreen demister vent. 7 passenger footwell heater outlets. 4 centre air vents. 8 control panel.
Page 263: Air Vents
AIR VENTS, air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre air vents. Side air vents Air flow Air flow To close the left-hand central air vent, To close the left-hand side air vent, slide the tab 9 fully to the left.
Page 264 MANUAL AIR CONDITIONING (1/4) Adjusting the ventilation fan speed. Turn control 3 from 0 to 4. The further to the right the control is positioned, the more air is blown into the passenger compartment. If you want to shut off the flow of air, set the 3 control to 0.
Page 265 MANUAL AIR CONDITIONING (2/4) Rear screen de-icing/ demisting With the engine running, press button 2. The integrated indicator light comes on. This function allows rapid electric de- misting of the rear screen and, depend- ing on the vehicle, electric de-icing of the rear view mirrors.
Page 266 MANUAL AIR CONDITIONING (3/4) Distribution of air in the The air flow is mainly distrib- uted between the front and passenger compartment rear footwells and the dashboard vents. Turn control 1 to choose the distribution Close the dashboard vents to direct all option.
Page 267 MANUAL AIR CONDITIONING (4/4) Switching air conditioning on The air conditioning system is used for: or off – lowering the temperature inside the The air conditioning is switched on (in- passenger compartment; dicator light lit) or off (indicator light off) –...
Page 268: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/4) Adjusting the ventilation speed. In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 1 to increase or reduce the ventilation speed.
Page 269 AUTOMATIC CLIMATE CONTROL (2/4) Clear View function Press the 2 button: the integrated indi- cator light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). It automatically activates the air condi- tioning and rear screen de-icing func- tions.
Page 270 AUTOMATIC CLIMATE CONTROL (3/4) Rear screen de-icing/ Switching air conditioning on demisting or off Press button 8 – the integrated indica- In automatic mode, the system switches tor light comes on. This function ena- the air conditioning system on or off, bles rapid demisting or de-icing of the depending on the climate conditions.
Page 271 AUTOMATIC CLIMATE CONTROL (4/4) Stopping the system Turn the control 1 to “OFF” to stop the system. To start it, turn the control 1 again, then adjust the fan speed or press the button 4. Air recirculation (isolation of Manual use the passenger compartment) Press the 7 button: the integrated indi- cator light comes on.
Page 272 AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap- air recirculation activated, ventilation fuel consumption (especially in town) proved dealer in the event of an oper- speed at zero or low etc.), you may when the air conditioning is operating.
Page 273 AIR CONDITIONING: information and operating instructions (2/2) Ñ Type of refrigerant fluid  Type of oil in the air condi- tioning circuit  Inflammable product  Consult the driver’s hand- book  Maintenance Quantity of refrigerant fluid present in the ve- x.xxx kg hicle.
Page 274 ADDITIONAL AIR CONDITIONING (1/2) Vehicle fitted with manual air On equipped vehicles, there are four adjustable air vents and a control con- conditioning sole 1. Make sure that the air conditioning is These controls only affect the amount operational (warning light on button 2 of air blown into the passenger com- lit up).
Page 275 ADDITIONAL AIR CONDITIONING (2/2) Vehicle fitted with automatic Note: the switch 3 and the control con- sole 1 are fitted with an operation warn- air conditioning ing light: Make sure that the air conditioning is – if switch 3 and warning light 5 are operational (warning light on A/C OFF 4 illuminated, this indicates that con- button illuminated).
Page 276: Multimedia Equipment
MULTIMEDIA EQUIPMENT (1/2) The presence and location of this Radio 3 Steering wheel controls 4 equipment depends on the vehicle’s On those vehicles equipped, you can multimedia equipment. use the hands-free telephone con- 1 Multimedia touchscreen. trols 5 and voice recognition 6. 2 Steering column control.
Page 277 MULTIMEDIA EQUIPMENT (2/2) Microphone 7 Induction charger 8 (depending on the vehicle) ➥ 3.25 Using the telephone We remind you of the need to conform to the legislation in force concerning the use of such equipment. 3.17...
Page 278: Windows
WINDOWS (1/3) Avoid resting any objects against a half-open window: there is a risk that the electric window could be damaged. Driver’s responsibility Never leave your vehicle with the card or key inside when there is a child, de- Electric windows From the front passenger seat pendent adult or a pet in it, even for Press switch 3.
Page 279 WINDOWS (2/3) Impossible to operate the Operating faults one-touch electric window In case of a fault when closing a window, the system reverts to normal mode: The one-touch electric window is pull the switch concerned up as often equipped with heat protection: if you as necessary to fully close the window press the switch for the window more (the window will close gradually), hold...
Page 280 WINDOWS (3/3) Sliding rear windows Move the handle 4 and slide the window to the desired notch. Sliding windows and doors Before moving them, ensure that no passenger has part of their body outside the window or door. 3.20...
Page 281: Sun Visor
SUN VISOR Sun visor Wide angle rear view mirror 2 Courtesy mirror 3 (depending on the vehicle) (depending on the vehicle) Lower sun visor 1. Lower the sun visor to access the Lower the sun visor to access the cour- The sun visor can be swung round wide-angle rear view mirror.
Page 282: Interior Lighting
INTERIOR LIGHTING (1/3) Courtesy lights Map reading light (depending on the vehicle) Using switches 1, 2 or 3 will activate: Move switch 4. – permanent lighting; – intermittent lighting, which comes on when a door is opened. It goes out when the doors concerned are prop- erly closed;...
Page 283 INTERIOR LIGHTING (2/3) Glove box light 5 Luggage compartment light 6 This lights up when the glovebox is It comes on when the boot is opened. opened. With the doors properly shut, lock- ing or starting the engine make the interior lights and the courtesy lights go out.
Page 284 INTERIOR LIGHTING (3/3) Light for rear seats 7 Rear light 8 Press the switch 7 to activate: Turn the switch 9 to activate: – permanent lighting; – permanent lighting; – lighting controlled by opening one of – intermittent lighting, which comes the doors.
Page 285 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/10) Cup holder 1 Passenger cup-holder 1 Right-hand driving position storage compartments This location can be used as a cup holder, a storage compartment or as a receptacle to fit the ashtray. Open storage compartment 2 Nothing should be placed on the floor (area in front of driver) as such objects may...
Page 286 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/10) It is essential not to leave any ob- jects (start-up card, USB drive, SD card, credit card, jewellery, keys, coins, etc.) in the induction charging area 4 whilst charging your phone. Remove all magnetic cards or credit cards from the case before position- ing your telephone in the induction charging area 4.
Page 287 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/10) Storage compartment 5 Radio location 6 Dashboard storage compartment 7 and 8 It can hold payment cards, money, A4- sized documents etc. Ensure that no hard, heavy Nothing should be placed or pointed objects are on the floor (area in front of placed in the “open”...
Page 288 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/10) Dashboard storage 9 Dashboard passenger storage compartment 10 and 11 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passen- gers during sudden turning, braking or in the event of an accident.
Page 289 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (5/10) Glove compartment 12 Right-hand driving position Passenger storage drawer 14 glovebox To open, press the control 13. To open, press control 15. Depending on the vehicle, the glove Depending on the vehicle, the glove box may have ventilation and air con- box may have ventilation and air con- ditioning (one 1.5 litre bottle can be...
Page 290 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (6/10) Front door storage Storage compartment 18 compartments 16 under the front seat To access this, pull the tabs 17 and tilt the seat base A forwards. Always close the seat base when driving: –...
Page 291 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (7/10) Seatback in table position Storage compartment 21 To open, press control 20. On equipped vehicles, lower the back of the centre seat by lifting the con- The strap 24 inside can keep an item trol 23.
Page 292 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (8/10) 20 22 Rear seat storage pockets 30 Tray 22 You can attach it using the document grip 28. To unlock the tray, press the control 20. To remove the tray, press the con- To install the tray, insert the end trol 29.
Page 293 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (9/10) Grab handle 31 Clothes hooks 32 Rear load area storage compartment 33 This offers support and can be held Depending on the vehicle, hooks may when the vehicle is being driven. be placed in the partition in the loading Reserved for the transport of objects space.
Page 294 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (10/10) Recess 34 and flap 36 Use the flap 36 to extend the load length: Depending on the length of the objects – pull the tab 35 to raise the seat B; being transported in the rear load area, you can use recess 34.
Page 295: Accessories Socket
ACCESSORIES SOCKETS (1/2) Accessories sockets The 1 socket and, depending on the vehicle, the 2, 3 and 4 sockets are designed for connecting accessories which have been approved by our Technical Department. Their power C o n n e c t a c c e s s o r i e s level should not exceed 120 Watts with a maximum power of...
Page 296 ACCESSORIES SOCKETS (2/2) Cup holders 5 and 6 This can be used to store a mobile ash- tray, drink cans, etc. If your vehicle is not fitted with a cigar lighter and an ashtray, these can be obtained from an approved Dealer.
Page 297 REAR HEAD RESTS To raise the headrest To refit the headrest Press button 1 and lift the headrest to Insert the headrest rods into the holes release it (tilt the seatback if neces- (tilt the seatback if necessary). Lower sary). the headrest as far as it will go, then lift until it locks into place.
Page 298 REAR BENCH SEATS: functions (1/4) Bench seat 2 Depending on the vehicle, there may be two rear bench seats: bench seat 2 Insert the buckles 3 into the housings 4 (2nd row of seats) and bench seat 1 before moving the seatback(s). (3rd row of seats).
Page 299: Rear Bench Seat: Functions
REAR BENCH SEATS: functions (2/4) Bench seat 1 To fold it down To fold down (depending on the vehicle) – Pull seat back unlocking strap 6; This can be folded away and folded – Hold the bars 7 and bring them to- down.
Page 300 REAR BENCH SEATS: functions (3/4) Removal/refitting of bench Removal – move the bench seat towards the rear of the vehicle to release the an- seat 1 and 2 First, release the side seat belts by un- chorage points (movement F); (depending on the vehicle) locking them from their unit.
Page 301 REAR BENCH SEATS: functions (4/4) Refitting – position the bench seat over the front anchorage points; Ensure that the bench seats – push the bench seat until it sits over are locked in place correctly the rear anchorage points; when refitting them. –...
Page 302: Luggage Cover
LUGGAGE COVER The luggage cover is made up of one or two rigid sections. There are two possible positions: – top position A; – the lower position B. Depending on the vehicle, you can lift the section 1 to a vertical position to make loading easier.
Page 303: Luggage Net
LUGGAGE NET (1/2) Fitting the luggage net On equipped vehicles, the luggage Lower mounting: net A can be used, when transporting behind the front seats – attach the net strap hook 5 onto the animals or luggage, to separate them ring 7 at the base of the bench seat;...
Page 304 LUGGAGE NET (2/2) Fitting the luggage net A Lower mounting: behind the rear seats – fix the net belt hook 5 onto the ring 8; Inside the vehicle on each side: – adjust the net strap so that it is taut. Upper mounting: Removal –...
Page 305: Transporting Objects
TRANSPORTING OBJECTS (1/2) Always position the heav- Transporting objects in the Ensure that the objects being trans- iest items directly on the ported are evenly distributed through- rear load area floor. out the loading area. Use the lashing points on Depending on the vehicle, secur- the luggage compartment floor, if ing rings 1 and 2 can be used to stop...
Page 306 TRANSPORTING OBJECTS (2/2) Special note for van version F max: 400 daN While driving with the right rear hinged door open, always secure transported loads. The left-hand door, which remains shut, should not be used to hold transported loads in place. Using the right rear hinged door open while driving should only be done in exceptional cases.
Page 307: Transporting Objects: Towbar
TRANSPORTING OBJECTS: towing (1/2) Fitting towing equipment Fitting the towbar coupling ball A: 1093 mm (43.03”) Position the ball within the range of bolts 1 or 2, to respect the height B, which must be between 350 and 420 mm, with the vehicle loaded (use the illustration example below).
Page 308 TRANSPORTING OBJECTS: towing (2/2) Special note related to connecting/ disconnecting a trailer to/from the towing system On each first connection and when a trailer is disconnected from the towing system (caravan, trailer, etc.) or when a Permissible nose weight, maxi- defective bulb is replaced in your vehi- mum permissible towing weight cle ➥...
Page 309: Roof Bars
ROOF BARS Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 310 3.50...
Page 311 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 312: Bonnet
BONNET (1/2) Before carrying out any action in the engine com- partment, you must switch off the ignition ➥ 2.3. Do not press down on the bonnet: there is a risk that the bonnet may accidentally close. Please note when work- ing close to the engine that To open the bonnet, pull the handle 1.
Page 313 BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.
Page 314: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information Reading the oil level It is normal for an engine to use oil for lubrication and cooling of moving parts The oil level should be read with the ve- and it is normal to top up the level be- hicle on level ground, after the engine tween oil changes.
Page 315: Engine Oil Level: Topping Up, Filling, Oil Change
ENGINE OIL LEVEL: topping up, filling, oil change (1/2) Before carrying out any Please note when work- Adding engine oil action in the engine com- ing close to the engine that partment, you must switch Use a funnel or protect the it may be hot.
Page 316: Oil Change
ENGINE OIL LEVEL: topping up, filling, oil change (2/2) Topping up/filling Oil change The vehicle must be parked on level Service interval: refer to the mainte- ground and the engine should be cold nance document for your vehicle. (for instance, before the engine is started up for the first time in the day).
Page 317: Levels
LEVELS (1/3) Before carrying out any action in the engine com- partment, you must switch off the ignition ➥ 2.3. Please note when work- ing close to the engine that  it may be hot. In addition, Coolant the engine cooling fan may ...
Page 318: Brake Fluid
LEVELS (2/3) Frequency of checking coolant level Level 2 Check the coolant level regularly It is normal for the level to drop as the (very severe damage is likely to be brake shoes become worn, but it must caused to the engine if it runs out of never drop lower than the “MINI"...
Page 319: Windscreen Washer Reservoir
LEVELS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle.  Windscreen washer reservoir Topping up...
Page 320: Tyre Pressure
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure loss warning system In the event of under-inflation (punc- tures, under-inflation etc.), warning light  appears on the instrument panel ➥ 2.26. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...
Page 321 TYRE PRESSURE (2/2) E: tyre pressures for the rear wheels Tyre safety and chain fitting: for infor- (motorway) or when driving with a mation on servicing conditions and, de- significant load. pending on the vehicle version, the use of chains ➥ 5.12. B: front tyre pressure when driving (non-motorway), or if less than 4 people occupy the vehicle.
Page 322: Battery
BATTERY (1/2) Replacing the battery For your own safety and to ensure correct opera- tion of the vehicle’s elec- trical equipment (lights, windscreen wipers, ABS etc.), it is essential that any operation on the battery (removal, disconnection etc.) is performed by a specialist professional.
Page 323 BATTERY (2/2) When the ignition is off, some consum- ers may also be switched off (dipped beam headlights, radio, ventilation, in- terior lighting etc.). When the level is extremely low, the message “Battery low start engine” is displayed. The charge status of the battery can decrease, especially if you use your ve- hicle: –...
Page 324: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 325 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning Do not scrape off mud or dirt without equipment or by spray- pre-wetting. ing on products not ap- proved by our Technical Allow dirt to accumulate on the exterior.
Page 326 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning stickers, decorative finish films, etc. Return the wiper stalk to the park po- sition ➥ 1.128. Check the mounting of This type of paint requires certain pre- You should do the following external accessories, additional lights cautions.
Page 327: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 328 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle perfumes etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
Page 329 Section 5: Practical advice Puncture, emergency spare wheel ..........Tyre inflation kit .
Page 330: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Vehicle fitted with a tyre pressure loss warning system In some cases (rear puncture, vehicle loaded with towing equipment etc.), it In the event of under-inflation (punc- ...
Page 331 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) To put the spare wheel back B Proceed in reverse order. Check that wheel carrier 4 is correctly positioned before tightening nuts 3 and 5. Note: do not fit the hubcap on the emer- gency spare wheel, so that you do not hide the safety message on the label on the emergency spare wheel.
Page 332 TYRE INFLATION KIT (1/4) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 333 TYRE INFLATION KIT (2/4) Vehicle fitted with a tyre pressure loss warning system In the event of under-inflation (punc-  tures, under-inflation etc.), the warning light appears on the instrument panel. ➥ 2.26. Depending on the vehicle, in the event of a puncture, use the kit located in the tool kit underneath the driver’s seat.
Page 334 TYRE INFLATION KIT (3/4) – after a maximum of 15 minutes, stop Once the tyre is correctly inflated, inflating and read the pressure (on remove the kit: slowly unscrew the in- pressure gauge 1); flation end piece of the container 3 to prevent any product spatter and store Note: while the bottle is emptying the container in plastic packaging to...
Page 335: Tyre Inflation Kit
TYRE INFLATION KIT (4/4) Precautions when using the The kit should not be operated for more than 15 consecutive minutes. The container must be replaced after the first use even if liquid remains inside. Following repair with the kit, do not travel further than 120 miles (200 km).
Page 336: Tools
TOOLS Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctly in its housing to reduce the risk of injury.
Page 337: Wheel Trim, Wheel
WHEEL TRIM, WHEEL Wheel trim 1 Wheel trim 4 Remove the wheel trim using hubcap Remove using hubcap tool 2 (located in tool 2 (located in the tool kit) by fit- the tool kit) by engaging the hook in the ting the hook into one of the openings opening near the edge of the trim.
Page 338: Changing A Wheel
CHANGING A WHEEL (1/2) Switch on the hazard warn- ing lights. Keep the vehicle away from Do not leave the tools un- traffic and on a level surface secured inside the vehicle where it will not slip. as they may come loose Apply the hand brake and engage a under braking.
Page 339 CHANGING A WHEEL (2/2) Insert the 2 jack horizontally so that Loosen the wheel nuts and remove the Remove the wheel trim ➥ 5.8. jack head pin 3 meets the 4 hole in the wheel. Use the wheelbrace 1 to slacken off the lower section of the body and closest to Fit the emergency spare wheel in place wheel bolts.
Page 340: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) The tyres are the only contact between When the tyre tread has been worn the vehicle and the road, so it is essen- to the level of the warning strips, they become visible 2: it is then necessary tial to keep them in good condition.
Page 341 TYRES (2/3) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures loss warning system Adhere to the tyre pressures (including which may be reached in hot weather In the event of under-inflation (punc- the emergency spare wheel).
Page 342 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. For your safety, please re- spect the speed limit.
Page 343 BATTERY: breakdown recovery (1/2) To avoid all risk of sparks: – Ensure that any power consumers (courtesy lights, etc.) are switched off before disconnecting or recon- necting a battery; – when charging, stop the charger before connecting or disconnecting the battery; –...
Page 344 BATTERY: breakdown recovery (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 345: Fuses
FUSES (1/2) Passenger compartment fuses Clip 1 If any electrical equipment does not Remove the fuse using tweezers 5, lo- work, check the condition of the fuses. cated at the back of flap 1. To access the fuses, pull the edge A To remove the fuse from the tweezers, of the storage compartment 1 firmly to- slide the fuse to the side.
Page 346 FUSES (2/2) Allocation of fuses (the presence and location of fuses depends on the vehicle equipment level) Symbol Allocation Windscreen washer Multimedia accessories socket, multimedia î screen Æ Front and rear second row accessories socket Ì Horn Ý Towbar socket ...
Page 347: Headlights And Side Lights: Replacing Bulbs
HEADLIGHTS AND SIDE LIGHTS: replacing bulbs (1/2) Please note when work- ing close to the engine that it may be hot. In addition, the engine cooling fan may  start at any moment. The warning light in the engine compart- ment reminds you of this.
Page 348 HEADLIGHTS AND SIDE LIGHTS: replacing bulbs (2/2) Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. LED dipped beam LED side repeaters5 headlights 3 Consult an approved dealer. Please see an authorised dealer. LED fog lights 4 Consult an approved dealer.
Page 349: Rear Lights: Changing Bulbs
REAR LIGHTS: changing bulbs (1/4) Rear light unit A Turn the light unit slightly and release it Direction indicator lights 3 to access the bulb holder 2. Pear-shaped, bayonet type PY 21W Remove bolt 1. Unclip the bulb holders by rotating them bulb.
Page 350 REAR LIGHTS: changing bulbs (2/4) Rear light unit B 6 Fog light (driver’s side only) Remove screws 5. Pear-shaped bayonet bulb W16W. Release the headlight unit. 7 Reversing light Turn the bulb holder 6 or 7 and release Pear-shaped bayonet bulb W16W. Replace the bulb concerned.
Page 351 REAR LIGHTS: changing bulbs (3/4) High-level brake light on rear Remove the light sideways from the outside to access bulb 9. hinged doors Pear-shaped, bayonet type P 21W Remove nuts 8. bulb. 5.23...
Page 352 REAR LIGHTS: changing bulbs (4/4) High-mounted brake light on Number plate lights Remove the light from the outside to access the bulb 11. tailgate The bulb is accessed in the same way Pear-shaped, bayonet type P 21W for both vehicles with hinged doors and Remove nuts 10.
Page 353: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/3) LED interior lights 1 and 2 Glove box light 3 (depending on the vehicle) Remove the lens using a tool such as a flat-blade screwdriver. Consult an approved dealer. Pull the bulb to remove it from its hous- ing.
Page 354 INTERIOR LIGHTING: changing bulbs (2/3) Lights 4 Type of bulb 2 : W5W (depending on the vehicle) Consult an approved dealer. Replace the bulb and refit the lens. 5.26...
Page 355 INTERIOR LIGHTING: changing bulbs (3/3) 5 light 6 light (depending on the vehicle) Remove the lens using a tool such as a flat-blade screwdriver. Bulb version Pull the bulb to remove it from its hous- Remove the lens using a tool such as a ing.
Page 356 RADIO FREQUENCY REMOTE CONTROL: battery (1/2) Operating faults If the battery is too weak to ensure cor- rect operation, you will still be able to start and lock/unlock the vehicle ➥ 1.32. Replacing the battery When refitting, ensure that the cover is correctly clipped on and the screw tight- Open the case at slot 1 using a flat- ened.
Page 357 RADIO FREQUENCY REMOTE CONTROL: battery (2/2) Precautions relating to Do not dispose of your used batter- batteries: ies in the countryside. Give them to – keep (new or used) bat- an organisation that collects and re- teries out of reach of chil- cycles used batteries.
Page 358: Card: Battery
CARD: battery (1/2) Check that the cover is clipped shut. The batteries are available from ap- proved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical con- tact.
Page 359 CARD: battery (2/2) Operating faults If the battery is too weak to ensure cor- rect operation, you will still be able to start and lock/unlock the vehicle ➥ 2.4. Precautions relating to batteries: – keep (new or used) batter- ies out of reach of children; –...
Page 360: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Before connecting an accessory to a socket, please ensure that you do not exceed the maximum power authorised for the socket ➥...
Page 361 WINDSCREEN WIPER BLADES (1/3) Windscreen wiper blades 1 Lift the windscreen wiper arm 3, press Refitting button 2 to release the blade 1. Offer up the blade 3 of the wiper arm 1 With the ignition on and the engine at an angle of 30°.
Page 362 WINDSCREEN WIPER BLADES (2/3) – In frosty weather, make sure that the wiper blades are not stuck by ice (risk of motor overheating). – Check the condition of the wiper Check the condition of the wiper blades. blades. You are responsible for their service life: Replace the wiper blades as soon as they begin to lose efficiency (ap-...
Page 363 WINDSCREEN WIPER BLADES (3/3) Rear screen wiper blade on Rear screen wiper blade on To refit rear hinged doors tailgate Proceed in the reverse order to re- moval. Make sure that the blade is cor- – Lift the wiper arm 4; –...
Page 364: Towing
TOWING: breakdown (1/3) Before towing, put the gearbox in neu- Unhitch the trailer, etc., if one is – Use a rigid tow bar. If a tral, unlock the steering column and re- being towed. rope or cable is used (where lease the parking brake.
Page 365 TOWING: breakdown (2/3) When activated, in the event that the lever is stuck in P, depress the brake paddle. It is possible to free the lever manually. To do this, unclip the base of the lever then place a tool (rigid shaft) in the slot 2 (located to the right or left of the lever).
Page 366 TOWING: breakdown (3/3) Use only Rear towing point 3 Front towing point (Vehicle without towing equipment) At the rear: Unclip cover 5 by inserting a flat-blade screwdriver or similar under the cover. – for vehicles without towing equip- Rear towing point 4 ment, towing point 3;...
Page 367: Fitting A Radio
FITTING A RADIO – In all cases, it is very important to follow the manufacturer’s instruc- tions carefully. – The specifications of the brack- Radio location 1 Location of the speakers 2 ets and wires (available from our (depending on the vehicle) Network) vary depending on the To install speakers, please consult an equipment level of your vehicle...
Page 368: Operating Faults
OPERATING FAULTS (1/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the card POSSIBLE CAUSES WHAT TO DO The card does not lock Card battery is flat.
Page 369 OPERATING FAULTS (2/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 370 OPERATING FAULTS (3/8) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are Battery terminals not tight, Retighten or reconnect the terminals, or clean them if weak or fail to light up and the starter battery terminals discon- they are oxidised.
Page 371 OPERATING FAULTS (4/8) On the road POSSIBLE CAUSES WHAT TO DO White smoke from the exhaust. In the diesel version, this is necessarily a ➥ 2.12 fault. Smoke may be caused by particle filter regeneration. Smoke under the vehicle when This is not necessarily a fault.
Page 372 OPERATING FAULTS (5/8) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel Fault with the electric assistance needed to turn the wheels. Consult an ap- motor.
Page 373 OPERATING FAULTS (6/8) Stopped POSSIBLE CAUSES WHAT TO DO The engine cooling fan starts to run This is not necessarily a fault. The after the ignition is switched off. engine cooling fan group may start to run in order to regulate the engine temperature.
Page 374 OPERATING FAULTS (7/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information ➥...
Page 375 OPERATING FAULTS (8/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the head- Traces of condensation may be a nat- In this case, the traces will disappear lights or rear lights. ural phenomenon caused by varia- slowly once the lights are switched on. tions in temperature and humidity.
Page 376 5.48...
Page 377 Section 6: Technical specifications Vehicle identification plates ............Technical information for the emergency services.
Page 378: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MMAC (Maximum permissible hicle identification plate should be all-up weight). quoted on all correspondence or 5 MTR (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MMTA (Maximum Permissible The presence and location of the in- Weight) front axle.
Page 379: Technical Information For The Emergency Services
TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES The QR Code on the A label allows Ensure that the A label is always visible emergency workers using a tablet or and present on the windscreen as well smartphone to immediately access the as the rear screen.
Page 380: Engine Identification
ENGINE IDENTIFICATION Please quote the engine identifica- tion information in area A in all cor- respondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine serial number.
Page 381: Dimensions
DIMENSIONS (in metres) (1/4) Van version...
Page 382 DIMENSIONS (in metres) (2/4) Complete vehicles without recent alterations Standard chassis Long chassis Standard van Raised van Standard van Raised van 3.098 3.498 5,080 5,480 1,014 0.968 1.615 1.628 2,312 → 2,165 1,953 → 1,997 2,476 → 2,509 1,953 → 1,997 2,476 →...
Page 383 DIMENSIONS (in metres) (3/4) Combi version...
Page 384 DIMENSIONS (in metres) (4/4) Complete vehicles without recent alterations Standard chassis Long chassis COMBI With 3rd row Without 3rd row With 3rd row Without 3rd row bench seat bench seat bench seat bench seat 3.098 3.498 5,080 5,480 1,014 0.968 1.615 1.628 2,312 →...
Page 385: Engine Specifications
ENGINE SPECIFICATIONS Versions 2.0 dCi Engine type (see engine plate) Cubic capacity (cc) 1997 Type of fuel Diesel Octane rating The label located in the fuel filler flap indicates the authorised fuels. Fuel types that meet European standards and are Diesel fuel compliant with standard EN 590 contains up to 7 % fatty acid methyl compatible with the engines ester in volume.
Page 386: Weights
WEIGHTS (in kg) (1/2) The weights indicated are for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult your approved Dealer. Versions (marketed depending on country) Standard VAN Raised VAN Maximum Permissible All-Up Weight (MMAC) Maximum Permissible Weight (MMTA) Weights indicated on the vehicle identification plate ➥...
Page 387 WEIGHTS (in kg) (2/2) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer. COMBI Versions (versions marketed depend on country) Maximum Permissible All-Up Weight (MMAC) Maximum Permissible Weight (MMTA) Weights indicated on the vehicle identification plate ➥...
Page 388: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 389: Service Sheets
SERVICE SHEETS (1/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 390 SERVICE SHEETS (2/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 391 SERVICE SHEETS (3/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 392 SERVICE SHEETS (4/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 393 SERVICE SHEETS (5/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 394 SERVICE SHEETS (6/6) VIN: ................... Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 395: Anticorrosion Check
ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 396 ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 397 ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
Page 398 ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.22...
Page 399 ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.23...
Page 400 ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.24...
Page 401 ALPHABETICAL INDEX (1/7) automatic gearbox (use) ........2.99 → 2.102 ABS ............1.103, 2.31 → 2.35 automatic gearbox selector lever......2.99 → 2.102 automatic locking of the doors while driving ...... 1.38 access vehicle ................0.3 accessories..............2.5, 5.32 battery accessories - installation ........... 3.49 breakdown recovery .........
Page 402 ALPHABETICAL INDEX (2/7) cleaning: driving position inside the vehicle ..........4.17 – 4.18 settings .............0.4, 1.43 → 1.48 driving recommendations ........2.18 → 2.23 clock ............1.114, 1.118 – 1.119 closing the doors ........... 1.23 – 1.24, 1.38 configuration menu ..........1.94 → 1.97 ECO driving ............2.18 →...
Page 403 ALPHABETICAL INDEX (3/7) filter hazard warning lights signal ..........1.127 air filter ................4.9 headlight beam adjustment ..........1.126 diesel filter ..............1.116 headrest..............1.39, 3.37 oil filter ..............4.5 – 4.6 heated seats ..............1.40 particle filter ............2.13, 2.15 heated windscreen ..........3.8 →...
Page 404 ALPHABETICAL INDEX (4/7) lights-on warning buzzer ........1.23 → 1.26 keys load permitted on the roof ......... 6.10 – 6.11 locking the doors ..1.2 → 1.11, 1.22 → 1.26, 1.32 – 1.33, replacing the battery ......... 5.28 – 5.29 keys ................1.2 → 1.6 1.35 →...
Page 405 ............1.108 remote control door locking overspeed warning ..........2.59 → 2.62 batteries ............5.28 – 5.29 remote control door locking unit ........1.2 → 1.4 RENAULT card paint use ...............2.4 → 2.7 maintenance ............4.14 → 4.16 replacement parking distance control.........2.88 → 2.95 headlight bulbs ..........
Page 406 ALPHABETICAL INDEX (6/7) side protection devices ............1.56 towing ................0.10 sign detection: overspeed warning ......2.59 → 2.62 towing a caravan ........ 3.47 – 3.48, 6.10 – 6.11 towing hitch.............5.8, 5.36 → 5.38 signals and lights ..........1.120 → 1.127 speakers towing rings ............3.43 →...
Page 407 ALPHABETICAL INDEX (7/7) warning lights.............1.100 → 1.117 washing ..............4.14 → 4.16 weights ..............6.10 – 6.11 welcome aboard your vehicle general introduction ............0.1 welcome aboard your vehicle ..........0.1 wheelbrace ................5.8 wheels (safety) ............5.12 → 5.14 wide angle rear view mirror ........1.99, 3.21 windows ................
Page 410 à999105433Sö î ê ä R5 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 122-122 BIS, AVENUE DU GENERAL LECLERC 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / renaultgroup.com...

Renault TRAFIC 2022 User Manual

Section 1: Getting to Know Your Vehicle

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Renault TRAFIC 2022

Summary of Contents for Renault TRAFIC 2022

Table of Contents