Please use this information only for the purpose of performing repair, maintenance and/or configuration services of the Sony products (hereinafter the "Repair services") under the service agreement entered into with the Sony group company (hereinafter the "Service agreement"). Using this information for any purpose other than the purpose described foregoing is forbidden.
Only the Authorized Servicer's officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-know and who have agreed to hold confidential this information (collectively hereinafter the "Permitted users") are permitted to access and use this information. To disclose or disseminate to any person other than the Permitted users is forbidden.
Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose described in Section (1) above.
Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author. (Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)
Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address: somk-gcs-tissnexim-adm@jp.sony.com
In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.
Revision of Information: This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before using it.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
WF-1000XM3 sold in Korea and Taiwan area are replaced rather than repaired. For Korea and Taiwan area, refer to the separately issued service manual dedicated for the Korean and Taiwan area models. Information on Korean and Taiwan area models are not included in this service manual.
All of the units included in the WF-1000XM3 (WF- 1000XM3L/WF-1000XM3R/Charging case) are required to repairing of this unit. Check in advance that you have all of the units.
COMPONENT MODEL NAME (WF-1000XM3)
Headset
L-ch
WF-1000XM3L
R-ch
WF-1000XM3R
Charging case
BC-WF1000XM3 (See Note)
Note: The charging case for US, CND, E, AUS, JE, PX, RU and LA models are not written as "BC-WF1000XM3". The charging case is written as "WF- 1000XM3".
SPECIFICATIONS
Headset
Power source: DC 3.7 V: Built-in lithium-ion rechargeable battery DC 5 V: When charged using USB
Operating temperature: 0°C to 40°C (32°F to 104°F)
Rated power consumption: 1 W (Headset), 3 W (Charging case)
Usage hours: When connecting via the Bluetooth device Music playback time: Max. 6 hours (NC ON), Max. 6 hours (Ambient Sound Mode), Max. 8 hours (NC OFF) Communication time: Max. 4 hours (NC ON), Max. 4 hours (Ambient Sound Mode), Max. 4.5 hours (NC OFF) Standby time: Max. 9 hours (NC ON), Max. 8.5 hours (Ambient Sound Mode), Max. 15 hours (NC OFF) Note: Usage hours may be shorter depending on the Codec and the conditions of use.
Charging time: Approx. 1.5 hours (Headset) (About 90 minutes of music playback is possible after 10 minutes charging.) Approx. 3.5 hours (Charging case) Note: Charging and usage hours may be different depending on the conditions of use.
Charging temperature: 5°C to 35°C (41°F to 95°F)
Mass: Approx. 8.5 g × 2 (0.3 oz × 2) (Headset) Approx. 77 g (2.8 oz) (Charging case)
Included items: Wireless Noise Canceling Stereo Headset (1) USB Type-C™ cable (USB-A to USB-C™) (approx. 20 cm (7.88 in.)) (1) Long hybrid silicone rubber earbuds (SS (1 line) (2), S (2 lines) (2), M (3 lines) (attached to the unit at the factory) (2), L (4 lines) (2)) Triple-comfort earbuds (S (orange) (2), M (green) (2), L (light blue) (2)) Charging case (1)
Communication specification
Communication system: Bluetooth Specification version 5.0
Output: Bluetooth Specification Power Class 1
Maximum communication range: Line of sight approx. 10 m (30 ft)1
Frequency band: 2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Compatible Bluetooth profiles2: A2DP / AVRCP / HFP / HSP
Supported Codec3: SBC / AAC
Transmission range (A2DP): 20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna's performance, operating system, software application, etc.
Bluetooth standard profiles indicate the purpose of Bluetooth communications between devices.
Codec: Audio signal compression and conversion format
Design and specifications are subject to change without notice.
System requirements for battery charge using USB
USB AC adaptor A commercially available USB AC adaptor capable of supplying an output current of 0.5 A (500 mA) or more
Apple, iPhone, iPod and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Google and Android are trademarks of Google LLC.
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license.
The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.
USB Type-C and USB-C are trademarks of USB Implementers Forum.
Other trademarks and trade names are those of their respective owners.
Notes on the License
This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of copyright for the software. Pleace access the following URL and read the contents of the license. https://rd1.sony.net/help/mdr/sl/19b/
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
ADVANCE PREPARATION WHEN REPAIRING
All of the units included in the WF-1000XM3 (WF-1000XM3L/ WF-1000XM3R/Charging case) are required to repairing of this unit. Check in advance that you have all of the units.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this service manual.
Abbreviations AEP: European area, East European area, CIS area (Moldova) and Middle East area (Israel) models AUS: Australian (Oceania area) model CH: Chinese model CND: Canadian model E: Middle East area (Except for Israel), South East Asian area (Except for India), East Asian area (Except for China, Korea, Taiwan area) and African area models JE: Tourist model LA: Latin American area model RU: Russian (CIS area: Except for Moldova) model
WF-1000XM3 sold in Korea and Taiwan area are replaced rather than repaired. For Korea and Taiwan area, refer to the separately issued service manual dedicated for the Korean and Taiwan area models. Information on Korean and Taiwan area models are not included in this service manual.
MODEL IDENTIFICATION
When identifying the destination of this unit, referring to the writing contents on the model number label etc. on the inner side of the charging case.
Note 1: Writing contents of the model number label may be changed in the midway of production. Note 2: Can not identifying the destination by referring to the main unit of the left and right headset (WF-1000XM3L/1000XM3R).
US, CND, PX, LA
AEP, UK
E, AUS, JE, RU
CH
COLOR VARIATIONS
(B) Black, (S) Platinum Silver
SERIAL NUMBER CHECKING METHOD
When checking the serial number, open the charging case lid and refer to the position shown in the figure below on the model number label engraved on the inside of the hinge.
Note: Serial numbers are not written on the left and right headset (WF1000XM3L/1000XM3R).
THE EACH UNIT MODEL NAME CHECKING METHOD
When checking the model name of each unit, refer to the figure below.
Note: The model name of the charging case is written as "BC-WF1000XM3" only for AEP, UK and CH models. Other destination models are written as "WF-1000XM3".
Left side headset
Right side headset
Charging case (US, CND, PX, LA)
Charging case (AEP, UK, CH)
Charging case (E, AUS, JE, RU)
OPERATION CHECK OF THE NFC FUNCTION AFTER COMPLETING THE REPAIRS
After completing the repairs of this unit, follow the procedure below to check normal operation of the NFC.
Preparation:
NFC compatible device (smartphone or music player etc.)
Procedure:
Turn on the NFC function of the NFC compatible device. (For details, refer to the instruction manual of your NFC compatible device. The figure below is a reference example)
Remove the left and right headset from the charging case. (The unit power is turns on (blue flashing) automatically) Note 1: If it is already removed the left and right headset from the charging case and the power is off, put it in the charging case again and remove it.
Touch the N-mark part of the NFC compatible device to the Nmark part of the charging case, the blue flashing changes from slow to fast, and the connection is completed. (After connection is complete, the blue flashing is return to slow) Note 2: If the screen of the NFC compatible device is locked, please unlock it and then touch it.
Attach the left and right headset to your ears. Then the audio playback from the NFC compatible device, and check that the sound is output from the left and right headset. Note 3: Sound is not output just by attaching a headset on one side. Be sure to attach the left and right headset.
Touch the N-Mark part of the charging case with N-Mark of the NFC compatible device again to disconnect the connection, and complete the operation check. Note 4: Before returning the product to the customer, refer to "INITIALIZING METHOD" and delete the Bluetooth device pairing information.
RESETTING METHOD
If this unit does not operate properly, perform the reset.
Note 1: Even if this work is performed, device pairing information is not deleted. Also, other settings are retained.
Resetting procedure:
Attach the left and right headset to the charging case.
Touch and hold the touch sensor control panel on the left side headset (WF-1000XM3L), and the indicator changes from red lighting to red flashing, then check the indicator is turn off and the then release your finger. Note 2: It takes about 20 seconds to touch and release the touch sensor control panel.
Touch and hold the touch sensor control panel on the right side headset (WF-1000XM3R), and the indicator changes from red lighting to red flashing, then check the indicator is turn off and the then release your finger. Note 3: It takes about 20 seconds to touch and release the touch sensor control panel.
The reset is complete.
INITIALIZING METHOD
After completing the repair, be sure to initialize this unit according to the following procedure.
Note 1: When this work is performed, all device pairing information is deleted and settings return to factory defaults.
Procedure:
Attach the left and right headset to the charging case.
Touch and hold the touch sensor control panel on the left and right headset simultaneously, and the indicator changes from red lighting to red flashing, then release the your finger while red flashing state. Note 2: It takes about 10 seconds to touch and release the touch sensor control panel.
The left and right headset indicator automatically changes from red flashing to 4 times of blue flashing, and when the indicator is turn off, initialization is complete. Note 3: When this operation is performed, it might not be able to connect to iPhone or PC. In that case, delete the registration of this unit on iPhone or PC, register the device again.
ABOUT REPAIR OF EACH UNIT
All units included in this unit can not be disassembled and repaired. Refer to the following according to the unit which has broken respectively.
Note: It is necessary to disassemble the charging case only when repairing and replacing the left side headset (WF-1000XM3L).
Left side headset: REPAIRING AND REPLACING OF THE LEFT SIDE HEADSET (WF-1000XM3L) (refer to the following)
Right side headset: REPAIRING AND REPLACING OF THE RIGHT SIDE HEADSET (WF-1000XM3R)
Charging case: REPAIRING AND REPLACING OF THE CHARGING CASE
REPAIRING AND REPLACING OF THE LEFT SIDEHEADSET (WF-1000XM3L)
The left side headset (WF-1000XM3L) will be replaced in the state of the finished product. It can not be repaired by disassembling the left side headset (WF-1000XM3L).
Also, if you replaced the left side headset (WF-1000XM3L), necessary to disassemble the charging case and replace the CASE NFC board at the same time.
When replacing the left side headset (WF-1000XM3L), perform the work for according to the following procedure.
Note 1: The repair parts of the left side headset (WF-1000XM3L) are including the CASE NFC board (with NFC sheet, adhesive sheet NFC) paired with the new WF-1000XM3L besides the new WF1000XM3L.
Check in advance:
Check that you have all of the left and right headset (WF-1000XM3L, WF-1000XM3R) and charging case, included in the WF1000XM3.
Be sure to check that there are no WF-1000XM3 in the surroundings (within about 50 cm). If using WF-1000XM3 in the surroundings (within about 50 cm), it may connect to another WF1000XM3.
Replacing procedure of left side headset (WF-1000XM3L):
Replace the broken left side headset with the new left side headset. Note 2: Change the long hybrid silicone rubber earbud or triple-comfort earbud to new WF-1000XM3L from the broken WF-1000XM3L.
Refer to "2. DISASSEMBLY", disassemble the charging case and replace the inside CASE NFC board with the new CASE NFC board and assemble as it was before. (The figure below is an image figure) Note 3: The repair parts of the left side headset are including the CASE NFC board (with NFC sheet, adhesive sheet NFC) paired with the new WF-1000XM3L besides the new WF-1000XM3L. Note 4:If you disassemble the charging case in order to replace the CASE NFC board, reuse the removed parts other than CASE NFC board (with NFC sheet, adhesive sheet NFC), adhesive sheet hall for fixing the case inner block and ornament hinge.
Attach the left and right headset to the charging case. Note 5: The left and right headset will display a warning message (3 times red flashing repeat), but proceed to the next step as it is.
Touch and hold the touch sensor control panel on the left and right headset simultaneously, and the indicator changes from warning message (3 times red flashing repeat) to red flashing (slow), in this state release the your finger. Note 6: It takes about 10 seconds to touch and release the touch sensor control panel.
The left and right headset indicator automatically changes from red flashing to 4 times of blue flashing, and when the indicator is turn off, pairing of left and right headset is complete. Note 7: When this operation is performed, it might not be able to connect to iPhone or PC. In that case, delete the registration of this unit on iPhone or PC, register the device again.
Check the operation of this unit and complete the left side headset replacement work.
REPAIRING AND REPLACING OF THE RIGHT SIDE HEADSET (WF-1000XM3R)
The right side headset (WF-1000XM3R) will be replaced in the state of the finished product. It can not be repaired by disassembling the right side headset (WF-1000XM3R).
When replacing the right side headset (WF-1000XM3R), perform the work for according to the following procedure.
Check in advance:
Check that you have all of the left and right headset (WF-1000XM3L, WF-1000XM3R) and charging case, included in the WF1000XM3.
Be sure to check that there are no WF-1000XM3 in the surroundings (within about 50 cm). If using WF-1000XM3 in the surroundings (within about 50 cm), it may connect to another WF1000XM3.
Replacing procedure of right side headset (WF-1000XM3R):
Replace the broken right side headset with the new right side headset. Note 1: Change the long hybrid silicone rubber earbud or triple-comfort earbud to new right side headset (WF-1000XM3R) from the broken right side headset (WF-1000XM3R).
Attach the left and right headset to the charging case. Note 2: The left and right headset will display a warning message (3 times red flashing repeat), but proceed to the next step as it is.
Touch and hold the touch sensor control panel on the left and right headset simultaneously, and the indicator changes from warning message (3 times red flashing repeat) to red flashing (slow), in this state release the your finger. Note 3: It takes about 10 seconds to touch and release the touch sensor control panel.
The left and right headset indicator automatically changes from red flashing to 4 times of blue flashing, and when the indicator is turn off, pairing of left and right headset is complete. Note 4: When this operation is performed, it might not be able to connect to iPhone or PC. In that case, delete the registration of this unit on iPhone or PC, register the device again.
Check the operation of this unit and complete the right side headset replacement work.
REPAIRING AND REPLACING OF THE CHARGING CASE
The charging case will be replaced in the state of the finished product. It can not be repaired by disassembling the charging case. When replacing the charging case, perform the work for according to the following procedure.
Check in advance:
Check that you have all of the left and right headset (WF-1000XM3L, WF-1000XM3R) and charging case, included in the WF1000XM3.
Be sure to check that there are no WF-1000XM3 in the surroundings (within about 50 cm). If using WF-1000XM3 in the surroundings (within about 50 cm), it may connect to another WF1000XM3.
Preparation:
Windows PC with the Bluetooth function
NFC compatible smartphone that installed the NFC Tag Data Writing Application
Note 1: For the NFC Tag Data Writing Application, refer to "BLUETOOTH INFORMATION WRITING METHOD". Note 2: Confirm the method of obtaining the NFC Tag Data Writing Application and its latest version with the each service headquarters.
Replacing procedure of charging case:
Replace the broken charging case with the new charging case.
Attach the left and right headset to your ears, then touch and hold the touch sensor control panel on the left and right headset simultaneously for about 7 seconds to entering the pairing mode state. (Voice guidance of "Bluetooth pairing" is heard from the left side headset, and it entering the pairing mode)
Connect with the PC with the Bluetooth function. Note 3: In order to check the Bluetooth address, it is necessary to connect the PC and this unit. It is also possible to display the Bluetooth address, by the Bluetooth connect to the walkman (NW-S series or NW-A series etc.) with Bluetooth function. In this example, describes how to display Bluetooth address using the PC. Note 4: For the Bluetooth connection method of the PC, refer to the manual of the PC to be used.
Display the device information of this unit connected via Bluetooth on the screen of a PC. Then open the "Properties", check the Bluetooth address of this unit, and take a memorandum the Bluetooth address. Note 5: The figure below is a reference example. The display method of Bluetooth address may be different depending on Windows OS. If your using PC's OS is Windows 8.1, open the "Control Panel → Device and Printers" in this order, right click the icon showing the model name (WF-1000XM3) of this unit and open its "Properties". Note 6: Check the device name carefully so as not to confuse Bluetooth address with other devices, and take a memorandum.
Write the Bluetooth information recorded in step 4 to the charging case using NFC compatible smartphone that installed the NFC Tag Data Writing Application. (Refer to "BLUETOOTH INFORMATION WRITING METHOD")
After writing the Bluetooth information, attach the left and right headset to the charging case.
Touch and hold the touch sensor control panel on the left and right headset simultaneously, and the indicator changes from red lighting to red flashing, then release the your finger while red flashing state. Note 7: It takes about 10 seconds to touch and release the touch sensor control panel.
The left and right headset indicator automatically changes from red flashing to 4 times of blue flashing, and when the indicator is turn off, the pairing information with the PC is deleted and initialization is complete. Note 8: When this operation is performed, it might not be able to connect to iPhone or PC. In that case, delete the registration of this unit on iPhone or PC, register the device again.
Check the operation of this unit.
Select the device (WF-1000XM3) displayed on the PC, right click and select "Remove device" from the displayed menu and delete the device (WF-1000XM3). Note 9: When another WF-1000XM3 is connected to the PC by Bluetooth connection, a new device (WF-1000XM3) will be added. If there are plural devices (WF-1000XM3), you may erroneously reference and write the Bluetooth address of another WF1000XM3. Therefore, delete the existing device before adding a new device.
Complete the replacement work on the charging case.
BLUETOOTH INFORMATION WRITING METHOD
When the charging case is replaced, it is necessary to perform writing of Bluetooth information.
Write the Bluetooth information according to the procedure below.
Preparation:
Windows PC with the Bluetooth function
NFC compatible smartphone that installed the file manager application (ASTRO File Manager, File Expert, etc.)
USB cable for the smartphone
NFC Tag Data Writing Application (Application name: mdr-nfc-tag-writer_2.0.1.apk)
Note 1: "2.0.1" in the file name indicates the version of NFC Tag Data Writing Application. Always use the latest version of the NFC Tag Data Writing Application. Example: mdr-nfc-tag-writer_2.0.1.apk Note 2: Confirm the method of obtaining the NFC Tag Data Writing Application and its latest version with the each service headquarters.
Notes on the use of the NFC Tag Data Writing Application
The NFC Tag Data Writing Application may be updated irregularly. Always use the latest version of the NFC Tag Data Writing Application. The version of NFC Tag Data Writing Application is represented by the file name of NFC Tag Data Writing Application. Example: mdr-nfc-tag-writer_2.0.1.apk
Be sure to uninstall older versions of the NFC Tag Data Writing Application before installing the latest version.
The NFC Tag Data Writing Application is also used in models other than the headphone category, and there are multiple types. If multiple NFC Tag Data Writing Applications are installed on a smartphone, do not launch more than one at the same time.
The NFC Tag Data Writing Application varies depending on your model. Be sure to use the specified NFC Tag Data Writing Application. Use of not specified NFC Tag Data Writing Application is strictly prohibited.
Installing the NFC Tag Data Writing Application Install the NFC Tag Data Writing Application on the smartphone for writing of Bluetooth information. If the NFC Tag Data Writing Application is already installed, confirm the following.
Be absolutely sure that the NFC Tag Data Writing Application supports your model.
Confirm that the NFC Tag Data Writing Application is the latest version. The version of NFC Tag Data Writing Application is represented by the file name.
Procedure:
Prepare the NFC Tag Data Writing Application on the PC. Note 1: Be absolutely sure that the NFC Tag Data Writing Application supports your model and that it is the latest version.
Using the USB cable for the smartphone, connect the smartphone and the PC, and transfer the NFC Tag Data Writing Application to the smartphone.
When tapping the "Settings" → "Security" on the screen of the smartphone, and check the "Unknown sources" checkbox. (The figure below is a reference example) Note 2: Depending on the version of Android OS, this setting may not exist. In that case, skip this step and proceed to the next step.
Disconnect the smartphone from the PC.
Use the file manager application to open the saved location of the NFC Tag Data Writing Application on the smartphone.
Tap on the NFC Tag Data Writing Application to open it, and install the NFC Tag Data Writing Application to the smartphone. (The figure below is a reference example)
When tapping the "Settings" → "Security" on the screen of the smartphone, and uncheck the "Unknown sources" checkbox. (The figure below is a reference example) Note 3: Depending on the version of Android OS, this setting may not exist. In that case, skip this step and proceed to the next step.
Complete install of NFC Tag Data Writing Application. (The figure below is a reference example) This completes the Installing the NFC Tag Data Writing Application.
Please proceed to the "2. Writing the NFC Tag Data".
Writing the NFC Tag Data Write NFC tag data (Bluetooth information) to the CASE NFC board inside the charging case.
Procedure:
Prepare the Bluetooth address (BD_ADDR) recorded in step 4 of "REPAIRING AND REPLACING OF THE CHARGING CASE".
Open the "NFC setting" from "Settings" on the smartphone screen and turn on the NFC function of the smartphone. (The figure below is a reference example) Note 1: Locations and names with settings may differ depending on the version of Android OS. Refer to the instruction manual of smartphone for more details.
Start the NFC Tag Data Writing Application on the smartphone. (The figure below is a reference example)
Tap the "Write" button.
Tap the "List" button and select the model name of the applicable to this unit from the list, or tap the "Bluetooth Local Name" to input the model name with the keyboard on the smartphone.
Tap the "Bluetooth Device Address" and input the Bluetooth address prepared in step 1 directly with the keyboard on the smartphone. Note 2: In the case of this unit, "QR" button is not used.
Check the "Read-only" checkbox is unchecked, and tap the "Write" button and check that "Writable" is displayed.
In the state of step 7, touch the N-mark part of the smartphone to the N-mark part of the charging case. Note 3: Be sure to touch the new charging case of repair parts. If you touch the charging case other than the one for repair, such as the charging case before replacement, an error will be displayed in the next step.
Check that "Success!" is displayed on the screen of the smartphone and tap "OK" button. Note 4: When "Success!" is not displayed, refer to "3. Error Display". Note 5: In the step 8, if you touch the charging case other than the one for repair, such as the charging case before replacement, an error will be displayed. In this case, restart from step 8 again.
End the NFC Tag Data Writing Application.
Check the operation of connecting smartphone and this unit with NFC function. (Refer to "OPERATION CHECK OF THE NFC FUNCTION AFTER COMPLETING THE REPAIRS")
Start again the NFC Tag Data Writing Application. (The figure below is a reference example)
Tap the "Write" button.
Check the "Read-only" checkbox is checked, and tap the "Write" button and check that "Read-only" is displayed.
In the state of step 14, touch the N-mark part of the smartphone to the N-mark part of the charging case. Note 6: Be sure to touch the new charging case of repair parts. If you touch the charging case other than the one for repair, such as the charging case before replacement, an error will be displayed in the next step.
Check that "Success!" is displayed on the screen of the smartphone and tap "OK" button. Note 7: When "Success!" is not displayed, refer to "3. Error Display". Note 8: In the step 15, if you touch the charging case other than the one for repair, such as the charging case before replacement, an error will be displayed. In this case, restart from step 15 again.
Tap the "Read" button.
In the state of step 17, touch the N-mark part of the smartphone to the N-mark part of the charging case.
Check that "BD_ADDR" displayed on the screen of the smartphone matches the Bluetooth address checked in step 1 and the "MODE" column is "0000 (Read-only)".
End the NFC Tag Data Writing Application.
Check the operation of connecting smartphone and this unit with NFC function. (Refer to "OPERATION CHECK OF THE NFC FUNCTION AFTER COMPLETING THE REPAIRS")
Complete writing the NFC tag data. Refer to the following as necessary. "3. Error Display" "4. Check Method of the NFC Tag Data" "5. The Factor that One Touch Connection (NFC function) is Impossible"
Error Display When the writing of the NFC tag data has failed, "Error" is displayed on the screen of the smartphone. When "Error" is displayed, operate according to the procedure below.
Procedure:
Tap "OK" button of "Error" display screen.
When error occurs in step 9 of "2. Writing the NFC Tag Data", operate the procedure from step 8 again. When error occurs in step 16 of "2. Writing the NFC Tag Data", operate the procedure from step 15 again.
If "Error" is displayed again in step 9 or step 16 of "2. Writing the NFC Tag Data", after tapping "OK" button on "Error" display screen, tap "" (or "" etc.) twice and return to the first screen. (The figure below is a reference example of an error case in step 9)
Tap the "Read" button.
In the state of the above step 4, touch the N-mark part of the smartphone to the N-mark part of the charging case.
Check that the "MODE" column is other than "0000 (Read-only)". Note: If "MODE" column is displayed as "0000 (Read-only)", NFC tag data can not be written. Prepare another new charging case again, and start to all over again writing the NFC tag data. (The charging case indicated as "0000 (Read-only)" can not be used)
Check Method of the NFC Tag Data If you want to check the NFC tag data of this unit after completing writing NFC tag data, check to the following procedure.
Preparation:
Windows PC with Bluetooth function
NFC compatible smartphone that installed the NFC Tag Data Writing Application
Procedure:
Attach the left and right headset to your ears, then touch and hold the touch sensor control panel on the left and right headset simultaneously for about 7 seconds to entering the pairing mode state. (Voice guidance of "Bluetooth pairing" is heard from the left side headset, and it entering the pairing mode)
Connect with the PC with the Bluetooth function. Note 1: In order to check the Bluetooth address, it is necessary to connect the PC and this unit. It is also possible to display the Bluetooth address, by the Bluetooth connect to the walkman (NW-S series or NW-A series etc.) with Bluetooth function. In this example, describes how to display Bluetooth address using the PC. Note 2: For the Bluetooth connection method of the PC, refer to the manual of the PC to be used.
Display the device information of this unit connected via Bluetooth on the screen of a PC. Then open the "Properties", check the Bluetooth address of this unit. Note 3: The figure below is a reference example. The display method of Bluetooth address may be different depending on Windows OS. If your using PC's OS is Windows 8.1, open the "Control Panel → Device and Printers" in this order, right click the icon showing the model name (WF-1000XM3) of this unit and open its "Properties". Note 4: Check the device name carefully so as not to confuse Bluetooth address with other devices.
Open the "NFC setting" from "Settings" on the smartphone screen and turn on the NFC function of the smartphone. (The figure below is a reference example) Note 5: Locations and names with settings may differ depending on the version of Android OS. Refer to the instruction manual of smartphone for more details.
Start the NFC Tag Data Writing Application on the smartphone. (The figure below is a reference example)
Tap the "Read" button.
In the state of step 6, touch the N-mark part of the smartphone to the N-mark part of the charging case.
Check that the alphanumeric characters of "BD_ADDR" displayed on the screen of the smartphone matches the Bluetooth address displayed on the PC in step 3. In addition, if "0000 (Read-only)" is displayed in the "MODE" column of the screen of the smartphone, NFC tag data has been written without any problem and can not be changed.
Select the device (WF-1000XM3) displayed on the PC, right click and select "Remove device" from the displayed menu and delete the device (WF-1000XM3). Note 6: When another WF-1000XM3 is connected to the PC by Bluetooth connection, a new device (WF-1000XM3) will be added. If there are plural devices (WF-1000XM3), you may erroneously reference and write the Bluetooth address of another WF1000XM3. Therefore, delete the existing device before adding a new device.
End the NFC Tag Data Writing Application on the smartphone. Also, end the "Properties" screen of the PC, and the check of the NFC tag data is completed.
The Factor that One Touch Connection (NFC function) is Impossible The four following factors are considered as the factor that one touch connection (NFC function) is impossible. Guess and check the defective factor by each checking result. Note: The four failure factors are examples.
Factor
Bluetooth manual connection check by user
NFC tag data check
Bluetooth manual connection check by servicing
NFC one touch connection check with smartphone
1
WF-1000XM3L (L-ch) defect
NG
―
NG
NG
2
CASE NFC board defect
OK
NG
OK
NG
3
NFC tag data writing failure
OK
NG
OK
NG
4
Smartphone trouble
OK
OK
OK
NG
DISASSEMBLY
This set can be disassembled in the order shown below.
DISASSEMBLY FLOW
Note: It is necessary to disassemble the charging case only when repairing and replacing the left side headset (WF-1000XM3L). This section only describes how to remove the CASE NFC board. For details, refer to "REPAIRING AND REPLACING OF THE LEFT SIDE HEADSET (WF-1000XM3L)".
SET (CHARGING CASE) ↓ ORNAMENT HINGE ASSY ↓ CASE INNER BLOCK ↓ INDICATOR LED ↓ CASE NFC BOARD
JIG When disassembling the unit, use the following jig.
Part No. 9-913-402-33
Description TOOL FOR DISASSEMBLING
Note: Follow the disassembly procedure in the numerical order given.
ORNAMENT HINGE ASSY
Remove the ornament hinge assy while slowly peeling off the adhesive sheet ornament.
Ornament hinge assy Note: When installing the ornament hinge assy, align the two bosses and two holes.
CASE INNER BLOCK
Insert the jig into the space and remove the two claws. Note 1: When using a jig, please work carefully so as not to damage the case outer and lid.
Claw
Open the lid.
Insert the jig into the space and remove the two claws. Note 2: When using a jig, please work carefully so as not to damage the case outer and case inner.
Claw
Lift up the case inner block in the direction of the arrow.
Peel the adhesive sheet hall off of the case outer.
Case inner block
INDICATOR LED
Peel the indicator LED off of the adhesive sheet NFC.
Draw the indicator LED out of the hole.
Indicator LED Note: When installing the indicator LED, align the two bosses and two holes.
CASE NFC BOARD
Lift up the CASE NFC board in the direction of the arrow.
Peel the CASE NFC board off of the case inner block.
Need Assistance?
Do you have a question about the WF-1000XM3 Series that isn't answered in the manual? Leave your question here.