Table of Contents
Advertisement
Quick Links
VISIT WEBSITE
CLICK HERE
BEFORE YOU BEGIN
ATTENTION: Read instructions
carefully before use.
Recommended setup procedures are
outlined in this document.
For safety reasons it is recommended
that at least two persons erect any
marquee setup.
Ensure the area is free from any sharp
objects, overhead structures or other
obstructions.
WARNING: Keep clear of
overhead power lines.
SIZES: 1.5m x 1.5m, 2.4m x 2.4m, 3m x 3m, 3m x 4.5m, 3m x 6m
CONTENTS
TRANSPORTING
THINGS YOU SHOULD KNOW
Your marquee is supplied with steel pins and
tie-down ropes. These MUST all be used. For
setup on hard surfaces such as pavement,
weight plates, water weights or sandbags
MUST be used for security.
These are add-on accessories that can be
purchased separately.
All roof tie-down straps MUST be attached
and tensioned. These security methods
will maximise safety. However, due to the
unpredictable nature of weather, damage
prevention is not guaranteed.
All folding marquees are considered temporary
structures and MUST be packed down and
stowed away in any adverse weather conditions
such as storm, rain or wind gusts. Your marquee
should never be left up unattended.
Prolonged exposure to the sun can seriously
degrade the material and/or cause it to
become discoloured.
1
1
PROTECTIVE COVER &
1
1
1
2
WARNING: KEEP ALL FLAME
AND HEAT SOURCES AWAY
FROM THE TENT FABRIC.
This marquee is built with flame
retardant. The fabric may burn if left
in continuous contact with any flame
source. The application of any foreign
substance to the marquee fabric may
render the flame-resistant properties
ineffective.
THIS PRODUCT MEETS AUSTRALIAN
STANDARDS
Please check with your local
regulations prior to purchasing this
item. Some municipalities have
restrictions and requirements.
3
5
6
9
10
Advertisement
Table of Contents
Related Manuals for Extreme marquees X6 VELOCITY
Summary of Contents for Extreme marquees X6 VELOCITY
-
Page 1: Table Of Contents
VISIT WEBSITE CLICK HERE BEFORE YOU BEGIN THINGS YOU SHOULD KNOW WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY ATTENTION: Read instructions Your marquee is supplied with steel pins and FROM THE TENT FABRIC. tie-down ropes. These MUST all be used. For carefully before use. -
Page 2: What You'll Need
WHAT YOU’LL NEED Stanley Knife / Scissors to open boxes. Only cut where symbol is shown on boxes. Mallet / Hammer to secure steel pins. PARTS LIST Standard package items listed below. Please note accessories are not listed here. 1x Protective Cover 1x Marquee Frame 1x Marquee Roof 8 x Pins... -
Page 3: Setup Instructions
SETUP INSTRUCTIONS Please read instructions completely before setting up your marquee. Make sure you have all the components identified on the Parts List. Recommended procedure below. For safety reasons it is recommended that 2 persons set-up / pack down any marquee. 1. -
Page 4: Pack Down Instructions
3MX6M SETUP INSTRUCTIONS Recommended procedure below. For safety reasons it is recommended that 2 persons set up any marquee. A. Middle Legs. B. Ensure protective flap is over the connector. Attach roof straps by looping straps around frame and engaging clip. Lift the front back roof connectors until pin locks in to position. - Page 5 8. Undo the velcro from the marquee roof and 6. Refer to ‘LIFT HERE To Take Down’ sticker 7. Grasp marquee truss bars and walk on the marquee. frame corners. marquee inwards. 9. Release the peak cap from the centre pole 10.
-
Page 6: Attaching Wheels
X5 & X6 PROTECTIVE COVERS - ATTACHING WHEELS Recommended procedure to follow in this document. What you’ll need: Stanley Knife or Scissors are required. 1. Prepare all parts for assembly. 2. Insert the bolt through the wheel and 3. Insert the assembled wheel and bolt into REMOVE the zip ties from wheels, keep the bearing. -
Page 7: Optional Accessories Instructions
OPTIONAL ACCESSORIES INSTRUCTIONS WHEELED MARQUEE - ATTACHING WHEELS 1. Lay marquee on its side over a bench or on 2. Locate ‘dimples’ on foot plate, position the 3. Tighten the wing nuts on the left/right side the ground and extend the inner leg. wheel on foot plate so that the wing nuts are until finger tight. - Page 8 FULL WALL INSTRUCTIONS 1. Put wall hooks through the eyelet holes of 2. Attach velcro tabs to marquee legs. 3. Completed Wall. inner roof flap (face hooks inwards). HALF WALL INSTRUCTIONS 1. Attach half wall display connector to 2. Insert half wall display bar through half wall 3.
- Page 9 VELCRO AWNING INSTRUCTIONS 1. Attach awning leg connector to 2. Attach awning velcro to the 3. Insert the (three piece) awning 4. Fit the awning end poles to the marquee frame. Repeat. velcro on marquee roof. pole in to the awning sleeve. connector and attached fabric.
-
Page 10: Banner Instructions
BANNER INSTRUCTIONS 1. Layout banner fabric, three stage banner 2. Small Banners / 2m pole, banner tip pole and protective cover. Extend the banner pole to the designated 2m line and twist the pole until secure. 3. Medium Banners / 3m Extend the banner pole to the designated 3m line and twist the pole until secure. -
Page 11: Important Information
MANUFACTURER’S WARRANTY your product for a replacement or refund within thirty (30) days of your purchase. The product must be in new, unused condition. Extreme Marquees does NOT accept returns for PRODUCT WARRANTY any custom printed products unless the custom printed product has a fault under our manufacturers warranty. - Page 12 RETURNING ITEMS Before returning any part or product to Extreme Marquees regularly in proportion to the frequency of use. please contact us to obtain specific return shipping Allow your marquee to completely dry before packing down instructions at logistics@extrememarquees.co.nz or call us and fitting the protective cover.
Need help?
Do you have a question about the X6 VELOCITY and is the answer not in the manual?
Questions and answers