Extreme marquees X7 TECTONIC Instructions & Care

Hide thumbs Also See for X7 TECTONIC:

Advertisement

Quick Links

VISIT WEBSITE
CLICK HERE
BEFORE YOU BEGIN
ATTENTION: Read instructions
carefully before use.
Recommended setup procedures are
outlined in this document.
For safety reasons it is recommended
that at least two persons erect any
marquee setup.
Ensure the area is free from any sharp
objects, overhead structures or other
obstructions.
WARNING: Keep clear of
overhead power lines.
SIZES: 3m x 3m, 3m x 4.5m, 3m x 6m, 4m x 4m, 4m x 6m, 4m x 8m
CONTENTS
TRANSPORTING
THINGS YOU SHOULD KNOW
Your marquee is supplied with steel pins and
tie-down ropes. These MUST all be used. For
setup on hard surfaces such as pavement,
weight plates, water weights or sandbags
MUST be used for security.
These are add-on accessories that can be
purchased separately.
All roof tie-down straps MUST be attached
and tensioned. These security methods
will maximise safety. However, due to the
unpredictable nature of weather, damage
prevention is not guaranteed.
All folding marquees are considered temporary
structures and MUST be packed down and
stowed away in any adverse weather conditions
such as storm, rain or wind gusts. Your marquee
should never be left up unattended.
Prolonged exposure to the sun can seriously
degrade the material and/or cause it to
become discoloured.
1
1
1
1
1
INSTRUCTIONS & CARE
WARNING: KEEP ALL FLAME
AND HEAT SOURCES AWAY
FROM THE TENT FABRIC.
This marquee is built with flame
retardant. The fabric may burn if left
in continuous contact with any flame
source. The application of any foreign
substance to the marquee fabric may
render the flame-resistant properties
ineffective.
THIS PRODUCT MEETS AUSTRALIAN
STANDARDS
Please check with your local
regulations prior to purchasing this
item. Some municipalities have
restrictions and requirements.
2
3
5
5
9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X7 TECTONIC and is the answer not in the manual?

Questions and answers

Summary of Contents for Extreme marquees X7 TECTONIC

  • Page 1: Table Of Contents

    VISIT WEBSITE CLICK HERE INSTRUCTIONS & CARE BEFORE YOU BEGIN THINGS YOU SHOULD KNOW WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY ATTENTION: Read instructions Your marquee is supplied with steel pins and FROM THE TENT FABRIC. carefully before use. tie-down ropes.
  • Page 2: What You'll Need

    WHAT YOU’LL NEED Stanley Knife / Scissors to open boxes. Only cut where symbol is shown on boxes. Mallet / Hammer to secure steel pins. PARTS LIST Standard package items listed below. Please note accessories are not listed here. 1x Protective Cover 1x Marquee Frame 1x Marquee Roof 8 x Pins...
  • Page 3: Setup Instructions

    SETUP INSTRUCTIONS Please read instructions completely before setting up your marquee. Make sure you have all the parts identified on the Parts List. Recommended procedure below. For safety reasons it is recommended that 2 persons set-up / pack down any marquee. 1.
  • Page 4: Pack Down Instructions

    3MX6M SETUP INSTRUCTIONS Recommended procedure below. For safety reasons it is recommended that 2 persons set up any marquee. 9. Middle Legs. 10. Ensure protective flaps are over the truss connectors. Attach them by looping the straps around the truss and engaging the clips, then Lift the front back roof connectors until pins locks in to position.
  • Page 5 8. Release the velcro from the marquee roof 6. Refer to ‘LIFT HERE To Take Down’ sticker 7. Grasp marquee truss bars and walk on the marquee. and frame. marquee inwards. 9. Release the roof cap from the centre pole 10.
  • Page 6: Protective Cover

    WHEELED PROTECTIVE COVER X7 Tectonic Range includes a wheeled protective cover bag for frame sizes 3x3m, 3x4.5m and 3x6m. MOVING WHEELED PROTECTIVE COVER 1. Ensure the protective cover is correctly secured over the Marquee. 2. Check area/path is clear of objects.
  • Page 7 FULL WALL INSTRUCTIONS 1. Put wall hooks through the eyelet holes of 2. Attach velcro tabs to marquee legs. 3. Completed Wall. inner roof flap (face hooks inwards). HALF WALL INSTRUCTIONS 1. Attach half wall display connector to 2. Insert half wall display bar through half wall 3.
  • Page 8 VELCRO AWNING INSTRUCTIONS 1. Attach awning leg connector to 2. Attach awning velcro to the 3. Insert the (three piece) awning 4. Fit the awning end poles to the marquee frame. Repeat. velcro on marquee roof. pole in to the awning sleeve. connector and attached fabric.
  • Page 9 BANNER INSTRUCTIONS 1. Layout of banner fabric, three stage banner 2. Small Banners / 2m pole, banner tip pole and protective cover. Extend the banner pole to the designated line 2m line and twist and keep twisting the pole to secure. 3.
  • Page 10: Important Information

    Q8 Quasar Frame 10 Years RETURNING ITEMS Wave / Flare Banner Hardware 1 Year Before returning any part or product to Extreme Marquees Cafe Umbrellas Frame 3 Year please contact us to obtain specific return shipping instructions at logistics@extreme-marquees.com.au or call...
  • Page 11 Should your marquee roof be damaged, please contact the truss bar screw is missing, replace it immediately as this will Extreme Marquees Office. We will assess the damage and put additional pressure on the frame when setting up. either suggest a repair centre or arrange to return the roof to our Warehouse/Office.
  • Page 12 call 1300 850 832 email admin@extreme-marquees.com.au shop www.extreme-marquees.com.au...

This manual is also suitable for:

X5 true blue series

Table of Contents