Gage Bilt GB54B Original Instructions Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB54B
  6. Original instructions manual

Gage Bilt GB54B Original Instructions Manual

Pneumatic installation tool
Hide thumbs Also See for GB54B:
Table of Contents

Advertisement

Quick Links

Download this manual
ORIGINAL INSTRUCTIONS
S/N: 1088 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
GB54B
PNEUMATIC INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT
44766 Centre Court, Clinton Twp., MI. 48038 USA
Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505
MADE in USA
solutions1@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB54B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB54B

Summary of Contents for Gage Bilt GB54B

  • Page 1 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB54B PNEUMATIC INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions1@gagebilt.com / www.gagebilt.com...

  • Page 2: Table Of Contents

    How to use the GB54B ................................9 Maintenance .................................... 10 Troubleshooting ..................................11 Overhaul ....................................12 Parts Lists ....................................13 Nose Assembly Selection Chart / Accessories ........................ 14-16 GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan U.S.A. +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN ISO 12100:2010 EN ISO 13849-2:2012 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str.

  • Page 4: Description And Technical Specifications

    The GB54B Installation tool is 8.36" (212.4 mm) high, has a .740” (18.8mm) stroke and generates a minimum of 700 lbs. (3.11 kN) pull load at 90 psi (6.2 bar). It operates on 90 psi-100 psi (6.2 bar-6.9 bar) of air pressure, with 90 psi. (6.2 bar) providing maximum efficiency.

  • Page 5: Description Of Functions

    DESCRIPTION OF FUNCTIONS Pintail Collection Bottle Cylinder Assembly Nose Assembly Air Exhaust Actuator Assembly Handle Image may not reflect actual tool GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Warnings

    4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 7: Principle Of Operation

    Air is exhausted through EXHAUST Rear Exhaust Port (Rear of tool) Rear Exhaust Port Plug removed. Side port plugged. Images may not reflect actual tool GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: How To Set-Up The Gb54B

    After nose assembly is completely threaded onto tool, back off nose until flat is in the desired position and tighten locknut. GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: How To Use The Gb54B

    Exert firm pressure against fastener during installation. Press actuator to start cycle. Release actuator as soon as fastener breaks. Repeat steps 1-4. Images may not reflect actual tool or fastener GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 10: Maintenance

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.

  • Page 11: Troubleshooting

    Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. (See proper nose assembly data sheet for detailed instructions). c) Incorrect follower. GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Overhaul

    (510102) which may be removed by removing the retaining rings (S15). It can be difficult to remove the pistons. Gage Bilt recommends using an “L” shaped rod (like a hex wrench) to facilitate removal. Insert the short end in the middle of the piston and pull the piston out.

  • Page 13: Parts Lists

    GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 14: Nose Assembly Selection Chart / Accessories

    GB54B ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB54B NOSE ASSEMBLY SELECTION CHART STRAIGHT (Sold Separately) Catcher Bag-Stem (715610) FASTENER DIA. STRAIGHT Effective FOD Control NUT PLATE RIVETS Use with XX-54-43 straight nose assemblies.
  • Page 15 This page intentionally left blank GB54B S/N: 1088 AND ABOVE Rev. 10/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 16 Riveter Kits Available (Sold Separately) Contact Gage Bilt to customize your riveter kit today. Approved Alternate Styles (Sold Separately) See GB50 nose assembly selection chart found on the GB50 flyer and manual at www.gagebilt.com GB50 Stroke - .740" (18.8 mm) Hand held weight - 1.80 lbs.

Table of Contents