1. Manuals
  2. Brands
  3. Interpack Manuals
  4. Industrial Equipment
  5. USA 2024-SB DH
  6. User manual

Interpack USA 2024-SB DH User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER MANUAL
USA 2024-SB DH
For Serial Numbers:
TM160 XX X XXX

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the USA 2024-SB DH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Interpack USA 2024-SB DH

Summary of Contents for Interpack USA 2024-SB DH

  • Page 1 USER MANUAL USA 2024-SB DH For Serial Numbers: TM160 XX X XXX...

  • Page 2: Table Of Contents

    ABLE OF ONTENTS Section 1 Table Of Contents------------------------------------------------- 2 Section 2 Revision Control--------------------------------------------------- 3 Section 2 Technical and Field Assistance------------------------------ 4-5 Section 3 Warranty-------------------------------------------------------------- 6 Section 4 Description of the USA 2024-SB Case Sealer----------- 7 Section 5 Important Safeguards-------------------------------------------- 8-15 Section 6 Specifications------------------------------------------------------- 16-20 Section 7 Set-Up Procedures------------------------------------------------ 21-34 Section 8 Operating Instructions------------------------------------------- 35-40...

  • Page 3: Section 2 Revision Control

    EVISION ONTROL REVISION CONTROL REV00 Initial Release REV01 Modified Index REV02 Final Release REV03 Updated REV04 Updated REV05 Updated UM094TW / UM594TW UDM094-04...
  • Page 4 Should you need to contact Interpack Technical Support, please have the Case Sealer model number and serial number available. This information can be found on the nameplate of the side panel of the machine. Interpack Technical Support is available during normal business hours (Eastern Time).
  • Page 5 Trouble Shooting section of this manual (pg 41-43). However, if after consulting the Trouble Shooting Section of this manual, you cannot remedy the problem, customer paid service support is available from your Authorized Interpack Distributor UM094TW / UM594TW...

  • Page 6: Section 3 Warranty

    Intertape sells its Interpack Tape Heads, Case Tapers and Case Erectors with the following warranties: 1. The HSD 2000 Tape Heads' knife blades, springs and wipe down rollers will be free from all ...

  • Page 7: Section 4 Description Of The Usa 2024-Sb Case Sealer

    USA 2024-SB C ESCRIPTION OF EALER Figure 1 The Interpack USA 2024-SB Carton Sealing Machine with HSD 2000 ETII Tape Heads is  designed to apply Intertape brand pressure sensitive carton sealing tape to the top and bottom center seam of regular slotted corrugated cartons. The USA 2024-SB is manually adjustable to a wide range of carton sizes (see Carton Size Capacity, page 20).

  • Page 8: Section 5 Important Safeguards

    Important Safeguards There are a number of safety labels used on Interpack Carton Sealers. These labels are placed at different locations (refer to Figure 2) on the machine to warn operators and service personnel of possible dangers. Please read the labels on the machine and the following safety precautions before using the machine.
  • Page 9 Important Safeguards Figure 2 UM094TW / UM594TW UDM094-04...
  • Page 10 Important Safeguards There Are A Number Of Safety Labels Used On Intertape Carton Sealers. The illustrated label as shown is attached to the Knife Guard inside the upper and lower HSD2000 ET II Tape Head. The label warns operators and service personnel of the very sharp knife used to cut the tape at the end of the tape application.
  • Page 11 Important Safeguards The label shown is affixed to the top squeezer assembly brackets on either side of the machine. They warn the operator of a potential pinch point between the top of the case and the top squeezer rollers. Keep hand away from this area when processing a case This label affixed to the electrical control box advises service personnel to connect...
  • Page 12 Important Safeguards The illustrated label shown is located on the side of the column. This label provides convenient safety instructions for the operator and service personnel in the operation of the Intertape Carton Sealing Equipment. Note: Should Any Of The Safety Labels Placed On The Machine Be Damaged Or Destroyed, Replacements Are Available.
  • Page 13 Important Safeguards Explanation of Signal Word Consequences Warning: Indicates a potentially hazardous situation, which if not avoided could result in death or serious injury or property damage Caution: Indicates a potentially hazardous situation, which if not avoided could result in minor or moderate injury or property damage Warning •...
  • Page 14 Important Safeguards Warning • To reduce the risk associated with mechanical and electrical hazards: a. Allow only properly trained and qualified personnel to operate and service this equipment. Operator Skill Level Descriptions Skill “A”: Machine Operator This operator is trained to use the machine with the machine controls, to feed cases into the machine, make adjustment for different case sizes, to change the tape and to start, stop, and to re-start production Important: the area supervisor must ensure that the operator has...
  • Page 15 Important Safeguards Operators Skill Level Required To Perform The Following Tasks On The Machine Operator Skill Number Of Operation Machine Condition Level Operators Running With Safety Protections Machine Installation & Set Up B & C Disabled Stopped By Pressing The Adjusting Case Size Emergency Stop Button Stopped By Pressing The...

  • Page 16: Section 6 Specifications

    PECIFICATIONS USA 2024-SB Machine Dimensions Figure-3 Machine Weight: 560 lbs. (254 kg) crated UM094TW / UM594TW UDM094-04...
  • Page 17 PECIFICATIONS USA 2024-SB Machine Components Tape Head See Section 7, Page 31 In This Manual For Tape Loading & Threading. Case Width Adjustment Top Squeezer Conveyer Height Adjustment Control Box Figure-4 UM094TW / UM594TW UDM094-04...
  • Page 18 PECIFICATIONS 1. Operating Conditions Use in a dry, relatively clean environment at 40° to 105° F (5° to 40° C) with clean dry cartons. Note: Machine should not be washed down or subjected to conditions causing condensation on components. 2. Power Requirements Electrical - 115 VAC, 60 HZ, 5.0 A (560 Watts) Compressed Air –...
  • Page 19 4. Tape Specifications Use Intertape Brand Pressure Sensitive Carton Sealing Tape. The machine can accommodate 2” (48mm) or 3” (72mm) wide tape, depending on tape heads supplied. A maximum tape roll diameter of 16” (406 mm) on a 3” (76 mm) diameter core can be installed on the tape head (Accommodates all Intertape brand film tape machine roll lengths).
  • Page 20 5. Carton Specifications Type • Regular Slotted Containers (RSC). • Other style cases may be processed. Consult factory for details. Material 125 to 275 psi bursting test, single or double wall B or C flutes. Weight 0 to 85 lbs. (0 to 38.6 kg) Size The case sealer can accommodate most cartons within the size ranges listed below.
  • Page 21 ROCEDURES 1. Receiving and Handling The machine is shipped to the customer fixed to a pallet. The machine is enclosed with either a corrugated sleeve and cap or an HSC corrugated box. The sequence below is step by step instructions to remove all packing materials. •...
  • Page 22 ROCEDURES 2. Caster Installation (If Purchased) Caster installation requires raising the machine to access the bottom of each leg. Please follow all possible safety procedures prior to and during this process a. With a fork lift, raise the machine to allow access to the bottom of each leg. b.
  • Page 23 ROCEDURES 3. Machine Height Adjustment Machine height adjustment requires raising the machine to adjust each leg. Please follow all possible safety procedures prior to and during this process The Carton Sealer must be installed on near level ground. Use the adjustable legs to ensure that the machine is level and firmly on the ground (no rocking).
  • Page 24 ROCEDURES 4. Installation of Interpack Brand In-Feed and Exit Roller Tables (If Purchased) Case Direction Figure-9 a. Install four (4) mounting studs into machine base with hardware included with roller figure-9 table, per b. Utilizing the slots in the roller table, attach roller table to machine base by locating mounting studs in slots on roller table and push down to lock in place.
  • Page 25 ROCEDURES 5. Installation of External In-Feed and Exit Conveyors Exit Conveyor In-Feed Conveyor Figure-10 a. Customer supplied in-feed conveyor (if used) should provide straight and level entry into the case sealer. b. Customer supplied gravity exit conveyor (if used) should be straight and declined no more than 20mm/meter away from the machine to convey the sealed cartons away from the machine.
  • Page 26 ROCEDURES 6. Machine Final Assembly The machine is shipped with all adjustment handles installed. Location of Adjustment Handles. Figure-11 UM094TW / UM594TW UDM094-04...
  • Page 27 ROCEDURES 7. Connecting Utilities Electrical Start E-Stop Figure-12 An eleven foot (11’) standard three conductor power cord with plug is provided for 115 V, 60 Hz, 15 amp electrical service, the receptacle must be properly grounded. Before the machine is plugged into the receptacle, ensure that all materials are removed from the machine.
  • Page 28 ROCEDURES 8. Relocating Operator Controls This case sealer is shipped with the operator controls mounted on the left hand side of the machine (when viewed from the in feed of the machine). Certain machines have the ability to relocate the operator controls to the opposite side.
  • Page 29 ROCEDURES Re-Locating Electrical Control Box Start E-Stop Figure-15 Moving the control box to the opposite side of the machine requires disconnecting and reconnecting electrical wires and components. Only trained and qualified service technicians should access an open control box. Please follow all possible safety procedures prior to and during this process a.
  • Page 30 ROCEDURES 9. Removing Tape Heads Prior to Tape Loading Removing Upper Tape Head Figure-16 a. Slide tape head toward the infeed end of machine and rotate up. b. Slide tape head toward the exit end of machine and lift out of rear slot. Removing Lower Tape Head Top Tape Head Box Assembly Removed For...
  • Page 31 ROCEDURES 10. Tape Loading The HSD 2000-ET II Tape Heads accommodate 2-inch (48mm) wide tape rolls, while the HSD 2000-ET II/3" Tape Heads accommodate 3-inch (72mm) wide rolls. a. Place the tape head onto a sturdy, flat surface. b. Move the peel off roller away from the mandrel. c.
  • Page 32 ROCEDURES Warning! The knife contained in the Tape Head is extremely sharp. Use caution when threading the tape to avoid personal injury. 11. Tape Threading Preparation Figure-19 Threading the tape in the Tape Head does not require any special tools. Pull approximately twelve (12) inches of tape from the roll and fold in half lengthwise, adhesive side to adhesive side.
  • Page 33 ROCEDURES 12. Tape Threading TAPE ROLL PEEL OFF ROLLER ADHESIVE SIDE GUIDE CLUTCH ROLLER ROLLER GUIDE ROLLER GUIDE ROLLER TAPE GUIDE SHOE APPLICATION Clutch Roller Adhesive ROLLER Side Knurled Guide Guide Roller Roller Guide Roller Figure-20 Figure-21 figure-20 a. As illustrated in , first thread the tape tail over the peel off roller.
  • Page 34 ROCEDURES 13. Re-Installing Tape Heads Figure-22 a. Insert exit end of tape head into rear slots. b. Rotate front of tape head down into front slots c. Push front of tape head down to seat in bottom of slot. UM094TW / UM594TW UDM094-04...

  • Page 35: Section 8 Operating Instructions

    PERATING NSTRUCTIONS Case Size Set Up Functions Figure-23 UM094TW / UM594TW UDM094-04...
  • Page 36 1. Initial Condition Figure-24 Figure-25 Figure-26 Figure-24 a. Raise the upper head as shown in Figure-25 b. Open side drives or centering guides as shown in Figure-26 c. Loosen each locking knob and open top squeezers as shown in UM094TW / UM594TW UDM094-04...
  • Page 37 2. Preparation Of Case To Be Processed Figure-27 Figure-28 a. Flap Folding Figure-27 Fold Minor Flaps In As Shown In Figure-28 Fold Major Flaps In As Shown In Figure-29 Figure-30 b. Over Fills And Void Fills. Figure-29 Figure-30 Over Fills As Shown In And Void Fills As Shown In Should Be Avoided To Assure Proper Processing Of The Corrugated Case.
  • Page 38 3. Case Width Adjustment Turn Case Width Handle As Shown in Figure-31 Until Side Drive Belts Contact Case. Side Drive Belts Should Contact The Case Firmly Enough So Case Processes Smoothly But Not So Firm As To Score The Side Of The Case.
  • Page 39 5. Top Squeezer Adjustment a. Slide Each Top Squeezer To Contact The Case Firmly Figure-34 And Tighten Each Locking Knob As Shown In Each Top Squeezer Should Be Firm Enough On The Case To Completely Close Any Gap On The Center Seam But Not So Firm As To Restrict The Smooth Processing Of The Case Figure-34 6.
  • Page 40 7. Review Of Case Processing Case Should Process Smoothly Through The Machine And Apply The Tape Evenly To Each Top And Bottom Major Flap With A 2 ¼” Tape Leg Applied To Each End Panel. Should The Case Processing Need Correction Please Refer To The Trouble Shooting Section In This Manual UM094TW / UM594TW UDM094-04...
  • Page 41 However, should a problem occur, we recommend that you consult the following table. If the problem you encounter is not discussed in this table, call Interpack Technical Support (see page 2 of this document).

  • Page 42: Section 8 Troubleshooting

    ROUBLESHOOTING ONTINUED Trouble Possible Causes Solutions Case Processes But Product Does Not Support The End Insert Proper Dunnage Material Leading End Panel Is Panel Of The Case To Provide Support Crushed Main Spring Tension On Tape Head Reduce Main Spring Tension. Too Strong See Tape Head Manual Provided With Tape Head...
  • Page 43 ROUBLESHOOTING ONTINUED Trouble Possible Causes Solutions Rear Tape Leg Is Tape Threaded Incorrectly Review Tape Threading Page 33 Folded Or Wrinkled Adhesive Build Up In Tape Path Clean Tape Guide Rollers To Provide A Free Rotation Clean Tape Path, Blade Dull Blade Replace Blade Excessive Unwind Tension From...
  • Page 44 Trouble Shooting section of this manual. However, after consulting the Trouble Shooting Section of this manual, you cannot remedy the problem, customer paid service support is available from your Authorized Interpack Distributor. UM094TW / UM594TW UDM094-04...
  • Page 45 REVENTATIVE AINTENANCE The USA 2024-SB has been designed and manufactured with the finest components to provide long, trouble free performance. General preventive maintenance will improve performance and prolong the life of the case sealer Please review the illustrations and chart below for information regarding machine And Tape Head maintenance Machine Preventative Maintenance Chart Frequency...
  • Page 46 REVENTIVE AINTENANCE Tape Head Preventative Maintenance Chart Frequency Item Action Required Material Weekly Monthly Quarterly Blade Guard Oiler Pad Lubricate Lightweight oil Hardware Re-tighten any loose hardware Replace any missing hardware Cutter Blade Inspect for wear Clean Solvent Cleaner Mandrel Assembly Disassemble &...

  • Page 47: Section 10 Preventive Maintenance

    REVENTIVE AINTENANCE Cleaning The Machine Side Belt Drive Base Column Shaft Connecting Chain Figure-36 Warning! Please Exercise All Safety Precautions Prior To Starting This Procedure. Disconnect Electrical Power And Wear Approved Safety Glasses a. Side Belt Drive Base Insert An Air Nozzle Along The Top Edge Of The Belt Into The Opening Of The Drive Base And Clean Out Any Dust And Dirt b.
  • Page 48 REVENTIVE AINTENANCE Lubricating the Machine Column Shaft Centering Chain Acme Drive Base Shaft Figure-37 a. Column Shaft. Lubricate Both Shafts With Industrial Grade Silicone. b. Acme Drive Base Shafts. Lubricate Both Shafts With Light Machine Grease. c. Centering Chain. Lubricate Chain With Chain Lubricant. UM094TW / UM594TW UDM094-04...
  • Page 49 & A ACHINE AINTENANCE DJUSTMENT Drive Belt Replacement Using a 4mm Allen key, remove screws (2) and remove drive base cover. Using appropriate Allen key and wrench, loosen belt tensioning bolts. Remove worn belt and replace with new belt. Using appropriate Allen key and wrench, tighten belt tensioning bolts.
  • Page 50 & A ACHINE AINTENANCE DJUSTMENT Intertape S/B drive idler pulleys are engineered to self-track to center. After tensioning, if the belts do not track on center, contact maintenance or your IPG Distributor. Using a 4mm Allen key, replace drive base cover as shown.
  • Page 51 & A ACHINE AINTENANCE DJUSTMENT Drive Belt Adjustment Using a 4mm Allen key, remove screws (2) and remove drive base cover. Using appropriate Allen key and wrench, tighten belt tensioning bolts. Be sure to adjust upper and lower tensioning bolts equally.
  • Page 52 PTIONAL QUIPMENT 3” Tape Head 2” Tape Head 3 Flap Folders Exit Table In Feed Table In Feed Table With Hold Down Device Castors UM094TW / UM594TW UDM094-04...

  • Page 53: Section 13 Schematic Diagrams

    CHEMATIC IAGRAMS Electrical Drawing UM094TW / UM594TW UDM094-04...
  • Page 54 A –I & P PPENDIX LLUSTRATIONS ARTS ISTS UM094TW / UM594TW UDM094-04...
  • Page 56 APPENDIX USA2024 SB DOUBLE TOP TH BOX USA 2024-SB DOUBLE TH...
  • Page 57 UM161TW USA 2024-SB DOUBLE TH...
  • Page 58 UM161TW ITEM NO. PART NUMBER DESCRIPTION QTY. USM1215 BASE ASSEMBLY USM0819 COLUMN 24 LEFT ASS'Y USM0818 COLUMN 24 RIGHT ASS'Y UPM3227 PVC ROL CHARCOAL DIA 1.9 X 4.50 UPM3226 PVC ROL CHARCOAL DIA 1.9 X 12.00 USM0812 DRIVE BASE ASSY LH USM0811 DRIVE BASE ASS'Y RH USM5062...
  • Page 59 USM1215 USA 2024-SB DOUBLE TH...
  • Page 60 USM1215 ITEM NO. PART NUMBER DESCRIPTION QTY. UAM0329 BASE SUB-ASS'Y UAM0275 LEG ASSEMBLY METRIC USM6111 DRIVE CENTRING ASS'Y USM6118 ELECTRIC ASSEMBLY USM1216 DOUBLE SLIDING BOTTOM TH Box USA 2024-SB DOUBLE TH...
  • Page 61 UAM0329 USA 2024-SB DOUBLE TH...
  • Page 62 UAM0329 ITEM NO. PART NUMBER DESCRIPTION QTY. UPI0109 OUTSIDE FRAME UPI0113 TRANSVERSE BRACING UPM4193 REAR GAP FILLER UPM3234EV OUTLET ROLLER BLOCK UPM3288EV OUTLET COVER USA SB UPI0114 SLIDING PAD R.H. UPI0115 SLIDING PAD L.H. UPM3229 INLET COVER UF 3713 CARRIAGE BOLT M6 - 1 x 12 UF3391 SS NYLON LOCK NUT M6-1.0 UF3170...
  • Page 63 UAM0275 USA 2024-SB DOUBLE TH...
  • Page 64 UAM0275 ITEM PART # DESCRIPTION QTY. UPM7640 LEG WELDMENT UPM7641 LEG ADJ USTMENT UPM7642 LEG FRICTION PLATE UF4230 L.W. ZINC M12 UF6393 HHCS M12-1.75 x 35 UF3680 FW M10 UF6371 L.W. M10 UF6314 HNR M10 x 1.5 UF4229 CARRIAGE BOLT M10-1.5 x 20 UF4231 FW M12 USA 2024-SB DOUBLE TH...
  • Page 65 USM6111 A-10 USA 2024-SB DOUBLE TH...
  • Page 66 ITEM PART # DESCRIPTION QTY. UPM0618 CHAIN #35-165 PITCH USM6111 UPM7583 SHAFT COLLAR UF6371 L.W. M10 UF6382 HHCS M10-1.5 x 25 mm UF6314 HNR M10 x 1.5 UF3680 FW M10 UPM3242 DRIVE SUPPORT SPACER UPM0576 BUMPER UF0840 SHCS M6-1 X 25mm UF1828 REG F.W.
  • Page 67 USM0817 A-12 USA 2024-SB DOUBLE TH...
  • Page 68 USM0817 ITEM PART # DESCRIPTION QTY. UAM0264 ELECTRIC BOX ASSEMBLY UPM0197EV STR.RELF METL.LIQDTGHT M20X1.5 (8-10mm) 4 UPM0341EV LOCKNUT M20 X 1.5(FOR STRAIN RELF) UPM0209 POWER CORD, 14/3 UPM0225 CABLE 18/3 TYPE SJ UF3646 SHCS M4-0.7 x 20 A-13 USA 2024-SB DOUBLE TH...
  • Page 69 UAM0264 A-14 USA 2024-SB DOUBLE TH...
  • Page 70 UAM0264 UAM0264/ ITEM PART # DESCRIPTION QTY. UPM7527 ENCLOSURE DEMEX HIBOX 132 X 232 UPM2211 BUTTON MUSHROOM 22mm 1 N.C. UPM2212 BUTTON GREEN 22mm 1 N.O. UPM0407EV DIN RAIL USA 2324 UPM7440EV TB END ANCHOR FOR DN SER UPM2209EV LEGEND PLATE "E-STOP" UPM2210EV LEGEND PLATE "START"...
  • Page 71 USM1216 A-16 USA 2024-SB DOUBLE TH...
  • Page 72 USM1216 A-17 USA 2024-SB DOUBLE TH...
  • Page 73 UAM0341 A-18 USA 2024-SB DOUBLE TH...
  • Page 74 UAM0341 Default ITEM NO. PART NUMBER DESCRIPTION /QTY. UPM6068 TH BOX SUPPORT BLOCK UPM6069 TAPE HEAD BOX SUPPORT RH UPM6072 BOTTOM TH BOX SUPPORT LH UF5404 FHCS M5 - 0.8 x 16 mm UPM6070 TH BOX PAD RH UF3093 M5-0.8 x 30 BHCS A-19 USA 2024-SB DOUBLE TH...
  • Page 75 UAM0330 A-20 USA 2024-SB DOUBLE TH...
  • Page 76 UAM0330 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM6068 TH BOX SUPPORT BLOCK UPM6069 TAPE HEAD BOX SUPPORT RH UPM6072 BOTTOM TH BOX SUPPORT LH UF5404 FHCS M5 - 0.8 x 16 mm UPM4569 TH BOX PAD LH UF3093 M5-0.8 x 30 BHCS A-21 USA 2024-SB DOUBLE TH...
  • Page 77 UAM0009 A-22 USA 2024-SB DOUBLE TH...
  • Page 78 UAM0009 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM0131 BRASS PIN UPM0037 HANDLE ADJUSTABLE (COLUMN) UF2136 ROD W/HOLE ZINC 3/8-16 X 2" UF1610 HNJ 3/8-16 A-23 USA 2024-SB DOUBLE TH...
  • Page 79 USM0819 A-24 USA 2024-SB DOUBLE TH...
  • Page 80 USM0819 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM9712 COLUMN 24 LEFT METRIC UPM0738EV COLUMN SHAFT UPM0741EV COLUMN CAP LEFT SIDE UPM2251 SAFETY BUMPER UF5400 FHCS M5-0.8 x 12 mm UF3680 FW M10 UF6371 LW M10 UF0301 HHCS M10-1.5 x 35 UF1157 FHCS M5-0.8 x 70 UPM4210...
  • Page 81 USM0818 A-26 USA 2024-SB DOUBLE TH...
  • Page 82 USM0818 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM9713 COLUMN 24 RIGHT METRIC UPM0738EV COLUMN SHAFT UPM2182EV COLUMN CAP RIGHT SIDE UPM2251 SAFETY BUMPER UF5400 FHCS M5-0.8 x 12 mm UF3680 FW M10 UF6371 LW M10 UF0301 HHCS M10-1.5 x 35 UF1157 FHCS M5-0.8 x 70 UPM4210...
  • Page 83 USM5062 A-28 USA 2024-SB DOUBLE TH...
  • Page 84 USM5062 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM7695 SUPPORT PLATE LH UPM4539 SUPPORT PLATE RH UPM7698 CROSS SHAFT TTHBOX UAM0331 SLIDING TOP TH BOX UPM4538 SQUARE BAR UF4313 FHCS M10-1.5 x 35mm UF6384 BHCS M10-1.5 x 40mm UF3680 FW M10 UF6371 LW M10 UF5402...
  • Page 85 UAM0331 A-30 USA 2024-SB DOUBLE TH...
  • Page 86 UAM0331 A-31 USA 2024-SB DOUBLE TH...
  • Page 87 UAM0332 A-32 USA 2024-SB DOUBLE TH...
  • Page 88 UAM0332 ITEM NO. PART NUMBER DESCRIPTION QTY. UPI0111 WHEEL SUPPORT PLATE UPM3285EV GUIDE BLOCK UPM7538 GUIDE BLOCK TOP UAM0288 KNOB CW 5mm PIN USA2324 UPM1659 WHEEL 2-7/8"DIA.COMPR.GUIDE UF0240 HHCS 3/8-16 x 1.75 UF6373 FHCS M6 - 1 x 55 A-33 USA 2024-SB DOUBLE TH...
  • Page 89 USM0812 10 11 4 19 28 27 A-34 USA 2024-SB DOUBLE TH...
  • Page 90 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM3283EV DRIVE BASE LEFT SIDE USM0812 UPM3281EV DRIVE BASE COVER LH UPM7116 MOTOR 1/3HP 21.4 : 1 UPM0129EV DRIVE PULLEY 50mm UPM0029 STRIP UHMW 2" X .03"THK UPM0663 BELT ENDLESS 50 x 2120 mm UPM1879EV TENSIONNER SLIDE UPM1233EV...
  • Page 91 USM0811 11 18 A-36 USA 2024-SB DOUBLE TH...
  • Page 92 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM3282EV DRIVE SECTION, RIGHT SIDE USM0811 UPM3280EV DRIVE BASE COVER RIGHT SIDE UPM0663 BELT ENDLESS 50 x 2120 mm UPM0129EV DRIVE PULLEY 50mm UPM0259 IDLER PULLEY UPM1879EV TENSIONNER SLIDE UPM1233EV IDLER PULLEY SHAFT 50mm UPM0112 SPRING LOCATOR PIN UPM0101EV...
  • Page 93 UAM0335 A-38 USA 2024-SB DOUBLE TH...
  • Page 94 UAM0335 ITEM NO. PART NUMBER DESCRIPTION QTY. UPM1169 ADJUSTABLE HANDLE UF3720 SSS 1/2-13 x 2.5in UPM4542 BRASS PIN UF1650 HEX JAM NUT ZINC 1/2-13 A-39 USA 2024-SB DOUBLE TH...
  • Page 95 UM9003 A-40 USA 2024-SB DOUBLE TH...
  • Page 96 UM9003 ITEM PART # DESCRIPTION QTY. USM8075 SECOND E-STOP BOX FOR USA UPM0225 CABLE 18/3 TYPE SJ UPM0341 LOCKNUT 1/2"(FOR STRAIN RELF) UPM0197 STR.RELF METL.LIQDTGHT 1/4-3/8 UPM0200 MTG. CLAMP,ADH.1.2"X1.2" UPM0222 TY-RAP,5.5"X.14" UPM0285 STRAIN RELIEF, NON-METAL A-41 USA 2024-SB DOUBLE TH...
  • Page 97 USM8075 A-42 USA 2024-SB DOUBLE TH...
  • Page 98 USM8075 ITEM PART # DESCRIPTION QTY. UPM7293 ENCLOS PB 1 HOLE NON METAL UPM2211 BUTTON MUSHROOM 22mm 1 N.C. UPM2209 LEGEND PLATE "E-STOP" UPM0341 LOCKNUT 1/2"(FOR STRAIN RELF) UPM0197 STR.RELF METL.LIQDTGHT 1/4-3/8 A-43 USA 2024-SB DOUBLE TH...
  • Page 99 Electrical Drawing A-44 USA 2024-SB DOUBLE TH...

Table of Contents