Related Manuals for Black Box SWI037A
Summary of Contents for Black Box SWI037A
- Page 1 © Copyright 1998. Black Box Corporation. All rights reserved. 1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746...
- Page 2 Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 SUPPORT Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
- Page 3 TRADEMARKS TRADEMARKS USED IN THIS MANUAL AT is a registered trademark of IBM Corporation. All applied-for and registered trademarks are the property of their respective owners.
- Page 4 POW-R-SWITCHES 4C AND 8C FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection...
- Page 5 NOM STATEMENT NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
- Page 6 POW-R-SWITCHES 4C AND 8C 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
-
Page 7: Table Of Contents
TABLE OF CONTENTS Contents Chapter Page 1. Specifications ....................6 2. Introduction....................8 3. Installation......................9 Mode Switch ..................9 Cabling to the Switch ................9 Cable Length ..................9 Power Connection................9 Setting the DIP Switch ..............10 Power Control ...................11... -
Page 8: Specifications
(5) or (9) front-mounted LEDs: (1) Power, (4) or (8) Output Status Connectors — All models: (2) DB9 female data connectors (pass-through) and (2) RJ-11 (expansion); SWI037A, SWI038A: (4) or (8) NEMA 5-15R power outlets; SWI037AE, SWI038AE: (4) or (8) IEC320 power outlets... - Page 9 Output: Up to 8 amps per output and up to 8 amps aggregate total Size — SWI037A, SWI037AE: 2.8"H x 8"W x 6.3"D (7.1 x 20.3 x 16 cm); SWI038A, SWI038AE: 1.8"H x 19"W x 8"D (4.6 x 48.3 x 20.3 cm) Weight —...
-
Page 10: Introduction
2056 individual outlets (256 arming codes x 8 outlets per unit, 8-port model). 4- and 8-port models can be mixed. Table 2-1. Available Models Code Name Type of AC Connector SWI037A Pow-R-Switch 4C (2) DB9 female, (2) RJ-11, (4) NEMA 5-15R power outlets SWI037AE Pow-R-Switch 4C (IEC) -
Page 11: Installation
CHAPTER 3: Installation 3. Installation IMPORTANT! Before attaching any cables or power plugs, make sure that the power is OFF on all equipment, including the Pow-R-Switch. A serial self-test is included to help you when installing the unit. 3.1 Mode Switch The DB9 data ports are configured DCE and DTE. -
Page 12: Setting The Dip Switch
POW-R-SWITCHES 4C AND 8C 3.5 Setting the DIP Switch Once again, before attaching any cables or power plugs, make sure power to all equipment is OFF. Select the proper data rate, word structure, and arming character. Connect the RS-232 connector(s) and plug in the 5-volt DC power supply. -
Page 13: Power Control
CHAPTER 3: Installation The self-test message is sent to the output (DCE) port. Note that the self-test message will not be sent to the DCE port. You can reverse the DTE/DCE selections of the two DB9 connectors by changing the Mode switch (see Section 3.1). - Page 14 POW-R-SWITCHES 4C AND 8C Table 3-2. Possible Settings of the Arming-Code DIP Switch ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII " *A switch position is ON when it is down (closer to the number that identifies it).
- Page 15 CHAPTER 3: Installation ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII & < > *A switch position is ON when it is down (closer to the number that identifies it).
- Page 16 POW-R-SWITCHES 4C AND 8C ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII *A switch position is ON when it is down (closer to the number that identifies it).
- Page 17 CHAPTER 3: Installation ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII *A switch position is ON when it is down (closer to the number that identifies it).
- Page 18 POW-R-SWITCHES 4C AND 8C ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII *A switch position is ON when it is down (closer to the number that identifies it).
- Page 19 CHAPTER 3: Installation ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII *A switch position is ON when it is down (closer to the number that identifies it).
- Page 20 POW-R-SWITCHES 4C AND 8C ARMING CODE DIP-SWITCH POSITIONS* HEX ASCII *A switch position is ON when it is down (closer to the number that identifies it).