Subscribe to Our Youtube Channel
Related Manuals for Electrolux Professional DC6-10HP
Summary of Contents for Electrolux Professional DC6-10HP
- Page 1 Installation manual Drying Cabinet DC6-10HP 427001232/EN Original instructions 2022.03.01...
-
Page 3: Table Of Contents
Contents Contents 1 Safety Precautions ..........................5 General safety information......................5 Symbols............................5 2 Technical data.............................6 Dimensions drawing........................6 Technical data ...........................7 3 Master and Slave heat pumps ......................8 4 Unpacking ............................9 Installation kit ..........................9 5 Weight reduction to facilitate installation ....................10 Remove the hanger section ......................10 Remove the doors........................ -
Page 5: Safety Precautions
Installation manual 1 Safety Precautions This appliance can be used in public areas. Remove all objects from pockets such as lighters and matches. WARNING. This appliance is intended only for drying textiles washed in water. DO NOT MODIFY THIS APPLIANCE. Servicing shall be carried out only by authorized personnel. -
Page 6: Technical Data
Installation manual 2 Technical data 2.1 Dimensions drawing fig.W01395 1395 1917 1931 1078 Control panel Condensation nipple ⌀ 10 mm, hose 3 m included Connecting cable 2.5 m included... -
Page 7: Technical Data
Installation manual 2.2 Technical data Capacity: kg of laundry Drainage capacity: g/min* Electrical connection: 220-240V 1 AC 50-60 Hz Traditional threaded fuse: Automatic fuse: Power: Hanging length: meters Weight: Sound pressure level: A-weighted emission sound pressure level <57 dB (A) Average heat emission per drying cycle used to assess ventilation need**: * 6.5 kg dry weight cotton, 50% residual moisture. -
Page 8: Master And Slave Heat Pumps
Installation manual 3 Master and Slave heat pumps fig.W01396 MASTER SLAVE The drying cabinet contains two heat pumps, a MASTER and a SLAVE. The heat pump on the left is the MASTER and the one on the right is the SLAVE. As the name implies, the MASTER controls the process, while the SLAVE follows. -
Page 9: Unpacking
Installation manual 4 Unpacking Removal all packing materials. Do not use sharp objects, as this could damage the product. Packaging materials such as plastic and styrofoam should be kept out of reach of children. 4.1 Installation kit fig.W01398 Screw T6S 6x75 galvanized for wall mounting Screw M6S 8x16 for mounting bracket Washer BRB 8.4x17x1.6 Wall plug... -
Page 10: Weight Reduction To Facilitate Installation
Installation manual 5 Weight reduction to facilitate installation The following can be done to reduce the weight of the drying cabinet and thereby facilitate installation. If all of the measures are implemented, the weight of the drying cabinet will be cut almost in half. •... -
Page 11: Remove The Doors
Installation manual 5.2 Remove the doors Right door • Undo the four fastening screws securing the hatch (A) and remove the hatch. • Remove the cover (B) from over the upper hinge and expose the door cable (C). Then detach the cable from the connector (D). - Page 12 Installation manual Left door • Remove the cover (F) from over the hinge. • Remove the hinge (G), which is secured with two screws. • Lift the door off of the drying cabinet. fig.W01401 Cover over the hinge Upper hinge...
-
Page 13: Remove The Dehumidifier Units
Installation manual 5.3 Remove the dehumidifier units • Detach the front plate (A), which is secured with two screws on the top under plastic plugs. Unplug the electrical connection between the door switches and the left dehumidifier unit. Then remove the front plate. •... - Page 14 Installation manual • Remove the hatch (C), which is secured with three screws at the bottom edge of the hatch. Do this on both the left and the right side. • Remove the air deflector (D). This is secured with two plastic Torx 40 screws, which are located under cover plugs (E).
- Page 15 Installation manual • Detach the electrical cables as illustrated. fig.W01404 Property’s reservation system Loose modular cable, black User interface (control panel), white cable LED lighting Door switch Mains connection MASTER SLAVE • Detach the condensation connection (F) from both units. •...
-
Page 16: Positioning/Attachment
Installation manual 6 Positioning/Attachment The drying cabinet is only intended for placement indoors in a dry place The drying cabinet may not be placed in an environment where high-pressure water is used for cleaning 6.1 Ventilate the room When the machine is in operation, the room temperature increases. Due to this, the room must have sufficient ventilation. -
Page 17: Attachment To The Wall
Installation manual 6.3 Attachment to the wall The cabinet must be attached to the wall to prevent tipping. The installation kit contains two angle brackets that are mounted on the upper part of the drying cabinet as illustrated. Use the provided screws. The brackets have grooves for adjustment to the wall. Secure the cabinet to the wall. -
Page 18: Connection To Floor Drain
Installation manual 7 Connection to floor drain The drying cabinet comes with a preinstalled hose for connection to a floor drain. The hose connection if found on both sides at the lower rear corner of the cabinet. fig.W01408 • Connect a new drain hose to one of the cabinet connections and route it to the drain. •... -
Page 19: Electrical Connection
Installation manual 8 Electrical connection The electrical installation may only be performed by qualified personnel. The drying cabinet is delivered ready for connection, with cable and grounded plug. Heating options Mains voltage Total output Recommended fuse Heat pump 230V 1~ fig.W01410 We recommend that the mains cable be equipped with a ground fault interrupter. -
Page 20: Connection To Reservation System
If the property has a reservation system for the laundry room, the drying cabinet can be connected to this. Connection is handled via an external electronics box that can be ordered from Electrolux Professional. This is con- nected to connector B on the Master unit. -
Page 21: Function Check
Installation manual 9 Function check May only be performed by qualified personnel. A function check must be performed when the installation is finished and before the appliance can be used. Whenever a repair has been made, a function check must be performed before the appliance can be used again. •... -
Page 22: Disposal Information
Installation manual 10 Disposal information 10.1 Disposal of appliance at end of life Before disposing of the machine, make sure to carefully check its physical condition, and in particular any parts of the structure that can give or break during scrapping. The machine’s parts must be disposed of in a differentiated way, according to their different characteristics (e.g. - Page 24 Electrolux Professional AB 341 80 Ljungby, Sweden www.electroluxprofessional.com...
Need help?
Do you have a question about the DC6-10HP and is the answer not in the manual?
Questions and answers