Advertisement
Single-Pole Wiring Application:
Step 5a
������
�������
����
������
�����
Insert wires
straight then twist
�����
clockwise
��� ��� ����
���� ����� ������
���� ���������
������
����
��� �������
�����
����
������� ����
�����
������
������� �������
Connect wires per WIRING DIAGRAM as follows:
Screw wire nuts on clockwise making sure no bare conductors show
below the wire connectors. Secure each connector with electrical tape.
• Green dimmer Ground lead to Green or bare copper wire in wall box.
• Black dimmer lead to Line (Hot) wall box wire removed from old switch.
• Blue dimmer lead to remaining wall box wire (Load).
• Cap Yellow dimmer lead with appropriate size wire nut.
• Proceed to Step 6.
3-Way Wiring Application:
Step 5b
�������
����
������
������
�����
Insert wires
straight then twist
�����
���
clockwise
������
�������
� �
�����
��� �������
������
������
�����
����
������� ����
�����
������
������� �������
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase
date. Leviton's only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co.,
Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product
is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied
warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular
purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty
obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Connect wires per WIRING DIAGRAM as follows:
Step 5b
Screw wire nuts on clockwise making sure no bare
con't
conductors show below the wire connectors. Secure each
connector with electrical tape.
• Green dimmer Ground lead to Green or bare copper wire
• Black dimmer lead to tagged Line (Hot) wall box wire
Electrical
• Blue dimmer lead to Load wall box wire.
Tape
• Yellow dimmer lead to remaining wall box wire.
Testing your Dimmer prior to mounting in wall
Step 6
box:
�����
����
�����
Dimmer Mounting:
Step 7
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Electrical
Tape
Restore Power:
Step 8
Installation is complete.
���� �����
������
����
�����
����
�����
������
�����
Air Gap Switch
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
in wall box.
identified when removing old switch.
• Restore power at circuit breaker
or fuse.
• Ensure that the Air Gap Switch is
pushed in fully.
• Carefully holding Dimmer as
shown, turn Dimmer ON by
pressing touch plate. Lights
should turn ON.
If lights do not turn ON, refer
to the TROUBLESHOOTING
section.
Air Gap Switch
Installation may now be
completed by carefully positioning
all wires to provide room in wall
box for dimmer. Mount dimmer
into box with mounting screws
supplied. Attach wallplate.
Restore power at circuit breaker or fuse.
NOTE: Ensure that the Air Gap Switch
is pushed in fully.
OPERATION
NOTE: The Green indicator light will illuminate when the Load is
OFF to facilitate access in the dark.
NOTE: If using the dimmer in a 3-way application, the lights will
turn ON at brightness set on dimmer's touch plate. The lighting can
be controlled from either the dimmer or the remote location.
ON: Tap the touch plate of the dimmer. The
lights will fade ON at the brightness level last
used (LED OFF).
OFF: Tap the touch plate of the dimmer. The
lights will fade OFF (LED ON).
BRIGHTEN & DIM: Press and hold the touch
plate of the dimmer to the desired light level.
Each time the touch plate is touched, the
state of the dimmer toggles between BRIGHT
and DIM.
AIR GAP SWITCH: On the lower left corner
of the switch plate, there is an Air Gap
Switch. When servicing light fixture, pull lever
out (OFF position). This will cut the power
to the fixture. After servicing is complete,
Air Gap
Indicator
push the lever all the way in (ON position) to
Switch
Light
restore power.
CLEANING: To clean touch plate, wipe it with
a clean damp cloth using clean water only,
dry thoroughly.
TROUBLESHOOTING
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly with wire connectors.
- Lamp power is less than the 40W.
• Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
- Air gap switch is open.
• Dimmer does not operate
- Dimmer BLACK wire miswired to lamp and Dimmer BLUE wire
miswired to LINE Hot. Reverse BLACK and BLUE wires.
NOTE: If further information is needed in identifying the HOT wire in a
3-Way application, go to Leviton's website at www.leviton.com.
For non-standard wiring applications, refer to
Wire Nut and Connector Size Chart
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
1- #12 w/ 1 to 3 #14, #16 or #18
2- #12 w/ 1 or 2 #16 or #18
1- #14 w/ 1 to 4 #16 or #18
2- #14 w/ 1 to 3 #16 or #18
PK-92939-10-00-0B
Advertisement
