Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Shel lab CAT180
Summary of Contents for Shel lab CAT180
- Page 1 CATALYST OVEN : CAT180 ODEL NSTALLATION PERATION ANUAL Sheldon Manufacturing Inc. P.O. Box 627 Cornelius, Oregon 97113 EMAIL: tech@Shellab.com INTERNET: http://www.Shellab.com/~Shellab 1-800-322-4897 (503) 640-3000 FAX (503) 640-1366 REV 01/14 4861680...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION 1.0 RECEIVING AND INSPECTION SECTION 2.0 GRAPHIC SYMBOLS SECTION 3.0 INSTALLATION SECTION 4.0 CONTROL PANEL OVERVIEW SECTION 5.0 PRECAUTIONS SECTION 6.0 OPERATION SECTION 7.0 MAINTENANCE SECTION 8.0 PARTS LIST UNIT SPECIFICATIONS WIRE DIAGRAM This unit is a special purpose oven for professional, industrial or educational use where the preparation or testing of materials is done at approximately atmospheric pressure and no flammable volatile, or combustible materials are being heated. -
Page 3: Receiving And Inspection
Section RECEIVING AND INSPECTION Your satisfaction and safety require a complete understanding of this unit, including its proper function and operational characteristics. Read the instructions thoroughly and be sure that all operators are given adequate training before attempting to put the unit in service. -
Page 4: Graphic Symbols
Section GRAPHIC SYMBOLS Your oven may be provided with a display of graphic symbols to help identify the use and function of the available adjustable components. These symbols, when shown, indicate: You should consult your manual for further description or discussion of a control or user item. -
Page 5: Installation
Section INSTALLATION Local city, county, or other ordinances may govern the use of this equipment. If you have any questions about local requirements, please contact the appropriate local agency. Installation may be performed by the end user. Under normal circumstances this unit is intended for use indoors, at room temperatures between 5... -
Page 6: Control Panel Overview
Section CONTROL PANEL OVERVIEW Figure 1 START Switch: The Start switch initiates the catalyst baking cycle. This switch is a push-release momentary action switch. When activated, a timer is set to run for five (5) hours. During this time the oven heats to a minimum of180°C and bakes the catalyst. -
Page 7: Precautions
Section PRECAUTIONS Do not place sealed or heat sensitive containers in or on the oven chamber. Keep all flammable materials away from the oven. This oven is NOT designed for use in Class I, II, or III locations as defined by the National Electrical Code. -
Page 8: Operation
Section OPERATION Power Supply: The power supply must be properly grounded (earthed) and correctly sized to match the unit data plate rating. The supply voltage must match the data plate voltage within 10%. When the cord is plugged into the supply, the green CYCLE COMPLETED light should turn ON. -
Page 9: Maintenance
Section MAINTENANCE Note: Prior to any maintenance or service on this unit, disconnect service cord from the power supply. Cleaning: Clean the oven interior on a regular basis. Clean the inside of the chamber thoroughly using a long swab and a disinfectant appropriate for your application. -
Page 10: Parts List
SECTION PARTS LIST Description 115V 220V Circuit Breaker 1100505 1100505 Cord Set – USA 1800516 1800537 Cord Set – Euro 1800541 CTRL Adj. AMB—525°F (set to 210°C) 1750650 1750650 CTRL Limit Disc 43°C 1750506 1750506 2350527 2350527 Heating Element (2ea) (parallel) (series) Pilot Light, green... - Page 11 WIRING DIAGRAM 1750506 OPENS AT 43˚ C 7850531 CYCLE TIMER, ERDI-4311, 8520502 -120V START TIMER, ERDI-6311, 8520506 -220V 240V WIRING 240V 7030528 RELAY 7030539 SOCKET 115V 7030536 RELAY 7030537 SOCKET RELAY COIL 1750650 SET TO 210˚ C 4650553 4650554 RED LAMP GREEN LAMP 2350507 (2) 120VAC/125W...
Need help?
Do you have a question about the CAT180 and is the answer not in the manual?
Questions and answers