To be covered by UL 62368-1, the socket-outlet shall be installed near the equipment and shall be easily accessible� DC Supplied Units only: The HIS-ML19 subject unit is to be powered by a Listed Power Supply suitable for the application with outputs at SELV/LPS or Class 2 levels rated 9.6-36.6VDC, 2.5 A max.
Safety and Regulatory Information Hazardous Locations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D; Class II, Division 2, Groups F and G; Class III; or non-hazardous locations only� Device is open-type and is to be installed in an enclosure suitable for the environment that is only accessible with the use of a tool�...
Mechanical Drawings Mechanical Drawings Front and Side Views 482.6 mm (19.00") 301 mm 398.8 mm 329.3 mm (11.9") (15.70") (12.97") 376 mm (14.8") 7.1 mm (0.28") Bottom View 409.8 mm (16.14") 60.9 mm (2.40") (Design to maximum depth of 69.0 mm to ensure future compatibility with later revisions 7.1 mm and replacement units.)
Mechanical Drawings Rear View 100 mm VESA Mounting Pattern (M4 screws provided, 16 mm maximum depth of screw) ML19H User Manual, 99154B, November 2022...
3� Ensure that the air temperature around the unit (top and bottom) will not exceed the rated specifications of the unit. f The maximum rated temperature for the HIS-ML19 is 50°C (122°F). f Remember that heat rises – the temperature at the top of the cabinet will be much hotter than at the bottom if air inside the enclosure is not actively circulating.
DVI VIDEO VGA VIDEO Video Connection The HIS-ML19 supports digital signals (DVI, HDMI, DisplayPort) through its DVI-D port and analog signals (VGA, RGB) through its VGA port. RGB (BNC, RCA), HDMI, and DisplayPort video sources require additional adapters� After selecting the appropriate interface, connect one end of your video cable to the input port ...
Page 9
Hope Industrial Systems. Many 3rd-party signal adapters are known to cause signaling issues� Power Connection The HIS-ML19 is available with either AC or DC power input. AC power input models accept 100 to 240 VAC, 1.5/0.75 A, 60/50 Hz. Loosen the retaining clip for the power cable on the rear of the monitor�...
Installation Instructions Connect and Set Up Touch Screen Applies to touch screen monitors only� If you ordered a touch screen monitor, a USB cable is supplied for the touch screen interface� To use the touch screen Serial (RS-232) interface, a serial cable may be ordered separately�...
Page 11
Installation Instructions Installing the Driver: Serial (RS-232) Connections Serial Connections must be made before installing the driver. 1� Connect one end of the Serial cable to the Serial input port on the rear of the monitor� Connect the other end to the Serial port on the host computer. Tighten the screw locks on the cable connectors to ensure adequate strain relief�...
Hope Industrial Systems will not assume liability for damage to internal electronics due to improper installation� Contact Hope Industrial Systems if you need additional assistance� 1� Refer to the drawing below for the cutout dimensions for the HIS-ML19. 453.4 mm (17.85") 366.8 mm...
Page 13
Installation Instructions 3� Cut a rectangular hole in the panel. f Cutout Dimensions (W x H) for the HIS-ML19: 453.4 mm x 366.8 mm (17.85" x 14.44"); ± 0.5 mm (0.020") 4� Clean and deburr the panel hole� 5� Separate the rear collar from the monitor by removing the 12 nuts.
Video Settings Video Settings Setting the Timing Mode Setting the timing mode of your computer graphics adapter (or other video source) is important for maximizing the quality of the screen image and for minimizing eye strain. The timing mode consists of the resolution (e.g. 1280 x 1024) and refresh rate (or vertical frequency; e.g. 60 Hz). After setting the timing mode, use the On-Screen Display (OSD) controls to adjust the screen image.
Video Settings Control Panel Buttons Use the control panel buttons located on the back of the monitor to display and adjust various settings on the On-Screen Display (OSD) menu. CONTROL PANEL BUTTONS 1� To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustments screens disappear automatically after 15 seconds.
Video Settings Button Control Functions Menu • Opens the OSD menu� • Exits the OSD menu and saves adjustments. Enter When the OSD menu IS NOT displayed: • Shortcut to Auto Image Adjust. When the OSD menu IS displayed: • Displays the control screen for the highlighted control.
Video Settings On-Screen Display (OSD) Menus To open the OSD menu, press button [1] once. The following screen will appear: Main Menu Description Auto Image Adjust Automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion� Contrast / Brightness Includes the Contrast and Brightness functions.
Video Settings Auto Image Adjust Menu The Auto Image Adjust menu automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion� NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your display, lower the video refresh rate to 60 Hz and set the resolution to its pre-set value�...
Video Settings Color Adjust Menu The Color Adjust menu provides several color adjustment modes, including preset color temperatures and a User Color mode which allows independent adjustment of red (R), green (G), and blue (B). The factory setting for this product is Native. Color Adjust Menu Description sRGB...
Video Settings Information Menu The Information menu displays the timing mode (video signal input) coming from the graphics card in the computer. See your graphics card's user guide for instructions on changing the resolution and refresh rate (vertical frequency)� NOTE: VESA 1280 x 1024 @ 60 Hz (recommended) means that the resolution is 1280 x 1024 and the refresh rate is 60 Hz�...
Page 21
Video Settings Manual Image Adjust Description Menu ECO Mode Provides lower power consumption by reducing the brightness. • Standard is the default brightness setting • Optimize reduces brightness by 25% • Conserve reduces brightness by 50% View Mode Allows the user to select from five image modes to find the optimal screen setting for different applications, as well as the default "Standard"...
Video Settings Setup Menu The Setup menu includes the Language Select, Resolution Notice, OSD Position, OSD Time Out, OSD Background, Auto Power Off, and Power Indicator functions. Setup Menu Description Language Select Allows the user to choose the language used in the menus and control screens�...
Cleaning Instructions Cleaning Instructions CAUTION! DO NOT USE ABRASIVE MATERIALS, SUCH AS PAPER TOWELS OR DIRTY SHOP RAGS, ON THE DISPLAY AS IT WILL SCRATCH THE PROTECTIVE COATING. ALWAYS USE A SOFT CLOTH, PREFERABLY MADE OF COTTON. All displays may be cleaned using any standard glass cleaner as long as there is no abrasive or oily content.
Troubleshooting Troubleshooting Video Troubleshooting IMPORTANT! If using a KVM extender, first try to resolve any problems using the solutions listed below. If the problem still exists, try bypassing the KVM extender. If this fixes the problem and allows the monitor to work properly, then the KVM extender is the source of the problem�...
Page 25
Troubleshooting Symptom Causes Solutions "Out of The source signal exceeds Adjust the computer settings to the monitor's Range" the maximum resolution native resolution: message box and/or refresh rate that the 1280 x 1024 @ 60 Hz and no image monitor can handle on the screen ( >...
Troubleshooting Touch Screen Troubleshooting Applies to touch screen monitors only� To be sure that you have the most current driver, please check the following address: https://www�HopeIndustrial�com/support/drivers/ Symptom Causes Solutions No response Touch screen cable is not Make sure either the USB or Serial touch when touching plugged in correctly.
Specifications Specifications Display Type Thin-film transistor (TFT) Active Matrix Liquid Crystal Size 19" diagonal Image Size (W x H) 374�8 mm x 299�8 mm (14�8" x 11�8") Native Resolution SXGA (1280 x 1024, 5:4 aspect ratio) Minimum Resolution VGA (640 x 480) Pixel Pitch 0�293 mm x 0�293 mm Number of Colors...
Specifications Video Input Connectors • HD-15, DVI-D • Optional adapters are available for other connection types (contact Hope Industrial Systems for details) Input Signal Formats • RGB Analog video, 0.7/1.0 Vp-p, 75 Ohms Compatible sync modes: Separate H/V sync • NOTE: NTSC/PAL composite input available (call for details) Horizontal Scan 24 –...
Specifications Electrical Monitor Input • AC power models – 100 to 240 VAC, 1�5/0�75 A, 60/50 Hz • DC power models – 9�6 to 36�6 VDC, 2�5 to 0�65 A, Class 2 or SELV/LPS Power Consumption ~ 16 W Power (Standby mode) <...
Warranty Statement Warranty Statement Who is Covered? This warranty covers the purchaser of this product only and is not transferable without our written consent� What Does This Warranty Cover and What is the Period of Coverage? We warrant this product to be free from defects in material and workmanship, subject to the conditions set forth below.
Page 32
Hope Industrial Systems, Inc. US / International 1325 Northmeadow Parkway, Suite 100 Roswell, GA 30076 United States Toll Free: (877) 762-9790 | International: +1 (678) 762-9790 | Fax: +1 (678) 762-9789 Sales and Customer Service: sales@HopeIndustrial.com Support and Returns: support@HopeIndustrial.com Accounting Department: accounting@HopeIndustrial.com www.HopeIndustrial.com...