Table of Contents
Advertisement
Available languages
Available languages
Default Priority channel 2 is 19 AM.
See § PRIORITY CHANNELS page 9.
8) VOX SET
Three parameters allow to adjust the VOX function: Sensitivity: L / Anti-vox
level: A / Vox delay time: t.
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the VOX SET menu.
2.
Push the rotary PUSH knob (6) to
LCD: A, L or t.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
To
another parameter other than the one displayed or...
4.
Push the rotary PUSH knob (6) to
parameter blinks on LCD.
5.
Turn the rotary PUSH knob (6) or press the UP/DN (18) keys on the microphone
to
modify
the value.
6.
Push again the the rotary PUSH knob (6) to
7.
Once the settings done, press the PTT switch (17) key to
ment mode. If no adjustment is made for 10 seconds, the unit automatically
exits the menu.
Sensitivity "L" : allows the adjustment of the microphone (original one or
-
optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level).Default value: 2.
-
Anti-Vox "A": allows disabling the transmission generated by the surrounding
noise. The level is adjustable. OF (according the squelch level) and from 0
(without anti-vox) to 9 (low level). Default value: Of.
Delay time "T" : allows avoiding the sudden cut of the transmission by
-
adding a delay at the end of speaking. The level is adjustable from 1
(short delay) to 9 (long delay). Default value; 1.
The Vox Adjustment does not automatically active the VOX function.
9) SWR ADJUSTMENT
This function allows to
adjust
the SWR (Standing Wave Ratio) by beep tones.
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
phone to
select
the SWR menu.
2.
Press the rotary PUSH knob (6). The radio automatically goes to
without pressing PTT switch (17) . The SWR measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
enter
MENU.
is displayed.
validate.
The current parameter blinks on
validate.
The current value of the selected
store
move
and
to next setting...
exit
the VOX Adjust-
enter
MENU.
is displayed.
TX
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to 1. 0 . The space
between two beeps became longer when SWR value moves away from1. 0 .
Display shows the SWR value. For example 2. 5 .
5.
Press PTT switch (17) to
*Volume of the beep tone is adjustable with VOLUME knob (1). Please check
that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 6.
10) MIC TYPE
The PRESIDENT WALKER III FCC can be used with an electret microphone as
well as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram
page 60). Turning on the unit, the type of the microphone is briefly dis-
played.
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the MIC TP menu.
2.
Push the rotary PUSH knob (6) to
LCD.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the type on the microphone EL (electret) or DY (dynamic).
4.
New Push the rotary PUSH knob (6) to validate. The parameter stops blinking.
a) Go back to point 1 to
(17) to
validate
and
5.
If no key is pressed, the unit
the display.
Default type of microphone is EL (electret).
11) PA SETTING
This function allows to
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the PA SET menu.
2.
Push the rotary PUSH knob (6) to
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the operating mode of the PA : I n, OF or PA.
4.
New Push the rotary PUSH knob (6) to validate. The parameter stops blinking.
a) Go back to point 1 to
mode
(17) to
validate
and
5.
If no key is pressed, the unit
the display.
12
exit
MENU mode.
disappears in the display.
enter
MENU.
validate.
The current parameter blinks on
adjust
another function or b) Press the PTT switch
exit
MENU.
disappears.
exits
MENU after 10 seconds,
select
the operating mode of Public Address.
enter
MENU.
validate.
The current value blinks on LCD.
adjust
another function or b) Press the PTT switch
exit
MENU.
disappears.
exits
MENU after 10 seconds,
is displayed.
disappears in
is displayed.
disappears in
Advertisement
Table of Contents
