PrimeVOLT PV 5KTL-D3/G2 User Manual page 14

Electricity Connection
A
B
A
B
PE
PE
DO1
ALM
SIG
D12
D11
GND
COM2
1 3
2
Threaded sleeve
RS485Communication
cable (22AWG)
Nut
5
① Download the APP in either of the following ways
Scan the QR code on the inverter to download the APP
Download the APP from the APP storeor Google Play.
Note: APP should access some permissions such as inverter's location.You need to allow all permissions to be granted in all
pop-up windows when installing the APP or in your own phone setting.
② Power on the inverter.
③ Connect the inverter.Open the bluetooth on your phone,then open the APP.
Then follow the instructions below:
Scanning machine SN barcode
Account name
Put the bar code into the box and it can be
scanned automatically.
If you cannot recognize or have no barcode,
select "Manual Connect".
Password
Can not find inverter code
Manual Connect
Remember Password
Inverter List
LOGIN
New inverters
REGISTER NEW USER
No new device...
Password forgotten Demo Connected inverters
xxxxxxx
Local
xxxxxxx
WLAN Configuration Local Setting
26
Three phase Grid-tied PV String Inverter User Manual
2 × M4 screw; �.�N.m
Pin Inverter
1 A
2 B
3 A
4 B
5 PE
6 PE
1 DO1
2 ALM
3 EXT_SIG
0.8~1.5N.m
4 DI2
5 DI1
6 GND
4
≤60mm
Stripping the cable, and then screw down
8mm
two nuts on the cover , use communication
wire to connect the nuts、screw sleeve and
protective cover.
Connection the different positive and
negative signal wires of the first RS485
1
cable from the data logger to Pin1 and
2
3
Pin2 of the 6-Pin terminal respectively.
4
If there is more than one inverter,
5
connection Pin3 and Pin4 to Pin1 and
6
Pin2 of another inverter.
XXXXXXXX
0.00Wh 0.00kWh
E-Today E-Total
0.00W 0.00W
0.00W
Basic
Current Power �.��W
Inverter Time Wrong
Peak Power �.��W
Do you want to synchronize date and
E-Today �.��Wh
Choose and click the inverter
time with the mobile phone?
you want to connect. E-Total �.��kWh
Temperature CANCEL -��.��℃
OK
DC-Input
i
Quick Setup Chart Home Log
Three phase Grid-tied PV String Inverter User Manual
④ Go to Console>Communication Setting > RS485 Setting > Modbus Page,check the Modbus address(the default
value is 1),and click to modify the address as required if necessary.
0.00Wh
E-Today
0.00W
Basic
Current Power
Peak Power
E-Today
E-Total
Temperature
DC-Input
Quick Setup Chart
5.4.4 Country code configuration (only for Administrator)
Grid Parameters
Go to Console
Administrator status.
Console
XXXXXXXX
XXXXXXXX
0.00kWh
Maintenance
E-Total
Access Management
0.00W
Communication Setting
Grid Parameters
0.00W
Feature Parameters
Power Limit
0.00W
0.00W
Reactive Power Control
0.00Wh
Masking Fault Detection
0.00kWh
-20.00℃
Other Setting
Logout
i
i
Home Log Console
Quick Setup Chart Home Log Console
> Grid Parameters page. Follow below to configure the country code for Australia only for
Login As Administrator
Enter administrator password
Cancel OK
Electricity Connection
Communication Setting
Basic Setting
RS485 Setting
RS485 Setting
ModBus
1
ModBus Address
Number range is 1 to 247
Cancel OK
You need to enter the login
password only for the first time.
Standard Code
AU (AS/NZS ����.�/.�)
AU (AS/NZS ����.�:����)
AU (AS/NZS ����.� Vector)
AU (AS ����_����)
Cancel
27