Download Print this page

Advertisement

Quick Links

IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Parts Identification
1
3
Parts Checklist
Ref.
Description
1
Headboard
2
Footboard
3
Side Rail - Left
Side Rail - Right
4
Mattress Base Board - Headend
5
6
Mattress Base Board - Footend
7
Storage Base Boards
200815
5
6
4
8
Qty
Ref.
1
1
1
1
1
1
2
Page 1 of 9
FRANCES OTTOMAN
LIFT UP BED
PLEASE READ this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
7
11
13
2
Description
Base Board Support Rails (Wood)
8
9
Mattress Base Support Rails
10
Corner Brackets
11
Mattress Base Lifting Handle
Feet for Headboard
12
13
Feet for Footboard LH
14
Feet for Footboard RH
7
9
12
10
12
14
Qty
5
2
2
1
2
1
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the FRANCES OTTOMAN LIFT UP BED and is the answer not in the manual?

Questions and answers

Summary of Contents for Time4Sleep FRANCES OTTOMAN LIFT UP BED

  • Page 1 FRANCES OTTOMAN LIFT UP BED PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
  • Page 2: Additional Tools Required

    Fittings Checklist HARDWARE NEEDED FOR BED ASSEMBLY (PACK A) Code Description Code Description Bolts (M8x30mm) for fitting corner brackets (10) to footboard (2) Allen Key (for M8 bolt) and side rails (3&4) and also fitting side rails to headboard & footboar d (1&2). Bolts (M8x45mm) for fitting feet (12,13&14) to Spring Washers (for M8 bolts)
  • Page 3 Bed Assembly - Use Pack 'A' Stage Stage 10mm Page 3 of 9...
  • Page 4 Bed Assembly - Use Pack 'A' Stage & & Stage & DO NOT TIGHTEN BOLTS YET Page 4 of 9...
  • Page 5 Base Board Assembly Stage & Carefully fit the wooden storage base board support rails being careful not to damage the fabric 100% on the internal face of the side rails. Make certain the bed is squared up as shown in the diagram then tighten all bed assembly bolts 100%.
  • Page 6 Gas Lift Assembly i) Untie the two mechanisms. Stage ii) Lift up mattress base board support bars. iii) Connect the piston stems SMALL GAP Hold up each arm and slide piston stem onto the threaded axle and fit loc-nut (G) using spanner (F). Note, do not over-tighten - a small gap needs to be left - see sketch.
  • Page 7 Mattress Base Assembly - Use Pack 'B' Stage SLIDE HEADEND MATTRESS BASE BOARD (5) UP AGAINST THE LIFTING ARM STOP PLATES. CAREFULLY SCREW x4 BOLT SETS INTO BASE BOARD AS SHOWN - DO NOT TIGHTEN 100% YET. BEFORE FITTING FOOTEND BASE BOARD (6) FIT BOTH PLATES (J) TO HEADEND BASE BOARD (5) AS SHOWN Page 7 of 9...
  • Page 8 Mattress Base Assembly - Use Pack 'B' Stage SLIDE FOOTEND MATTRESS BASE BOARD (6) INTO POSITION LOOSELY CONNECT (6) TO THE PLATES THEN SCREW OTHER x4 SETS OF BOLTS INTO PLACE 100% WHEN ALL x16 BOLT SETS ARE IN PLACE, MAKE SURE SIDES OF BASE BOARDS ARE IN LINE WITH EACH OTHER, THEN TIGHTEN ALL BOLTS 100% Page 8 of 9...
  • Page 9 Base Board Assembly Stage Warning.! Note: Be very careful what you store under the bed - the top of an item, like a suitcase or a box, must not touch the underside of the mattress base or it may get damaged.