Time4Sleep RHAPSODY OTTOMAN LIFT UP BED Assembly Instructions Manual

Advertisement

Quick Links

IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
An instructional video of the Operation of the Ottoman Lift Up system is available via YouTube using
the following address:

Parts Identification

1
HEADEND
3

Parts Checklist

Ref.
Description
1
Headboard
2
Footboard
3
Side Panel - Left
4
Side Panel - Right
5
Metal Slat Frame
180115
5
4
Qty
1
1
1
1
1
Page 1 of 8
RHAPSODY OTTOMAN
LIFT UP BED
PLEASE READ this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
https://youtu.be/hyq4zm7h_yU
FABRIC
HANDLE
FOOTEND
2
Ref.
Description
6
Angle Brackets
7
Cross Bar
8
Mattress Stoppers
9
Slat Frame Support Rail (wood)
10
Fabric Base Cover
6
7
8
9
10
Qty
2
1
2
1
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RHAPSODY OTTOMAN LIFT UP BED and is the answer not in the manual?

Questions and answers

Summary of Contents for Time4Sleep RHAPSODY OTTOMAN LIFT UP BED

  • Page 1 RHAPSODY OTTOMAN LIFT UP BED PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
  • Page 2 Fittings Checklist HARDWARE NEEDED FOR BED ASSEMBLY (PACK A) Code Description Code Description Bolts (M8x30mm) for Allen Key (for M8 bolt) fitting side rails (3&4) and to headboard & footboard (1&2) Bolts (M8x50mm) for fitting Spring Washers (for M8 bolts) Slat Frame Support Rail (9) to Footboard (2) Flat Washers (for M8 bolts)
  • Page 3 Bed Assembly - Use Pack 'A' Stage Fit two sets of bolts (A), spring washers (B) , and flat washers (C) to the holes in the headboard (1) as shown. Note: Do not tighten fully but leave 10mm protruding as in the diagram. Fit the side panels (3 &...
  • Page 4 Bed Assembly - Use Pack 'A' Stage Fit the two angle brackets (6) loosley screwing the bolts (A), spring washers (B) & flat washers (C) into the threaded inserts in the corners of footboard (2) & the side rails (3&4). Fit slat frame support rail (9) to footboard (2) using two bolts (F) &...
  • Page 5 Assembling Slat Frame - Use Pack ‘B’ Stage Fitting position for cross Bar (7) is clearly labeled. Pass bar through Metal Slat Frame (5)between first & second slat. Carefully open the frame. Ease the plates on top of the cross bar (7) onto top of the slat frame sides and loosely fit two sets of bolts (J) &...
  • Page 6 Fitting Slat Frame - Use Pack 'B' Stage HOLD THEM FORWARD UN-TIE THE TWO MECHANISMS Slat Frame Support Bar iii) During this next step, the assistant should hold up the slat frame. On side panels (3&4) slide gas-lift piston stems (X) onto the axles (Y) then fit the flange lock-nuts (H).
  • Page 7 Fitting Slat Frame - Use Pack ‘B’ Stage With help from your assistant, lift slat frame (5) onto slat frame support bars aligning first set of holes on slat frame with first set of holes in support bars (nearest to headboard).
  • Page 8 Fitting Slat Frame Stage Note: Be very careful what you store under the bed - the top of an item, like a suitcase or a box must not touch the slats or they may be damaged. Maximum storage height is 185mm. Stage Push x2 Mattress Stoppers (8) into metal frame, they should go all the way through the upper &...

Table of Contents