Subscribe to Our Youtube Channel
Related Manuals for Poly Edge B30
Summary of Contents for Poly Edge B30
-
Page 1: Table Of Contents
Home PBXware SERVERware TELCOware SIPmon SIPProt Desktop & Mobile UADs Appliances From Bicom Systems Wiki Contents 1 Introduction 2 Requirements 2.1 Identifying phone model 2.2 Phone firmware 2.3 DHCP server 2.4 PBXware version 3 Installation 3.1 Power adapter 3.2 Power over Ethernet (PoE) 3.3 Find the phone IP address 3.4 Reset to factory settings 4 Registering phone... -
Page 2: Requirements
To start and successfully complete registration of your Poly Edge B30 phone you need to know which phone model you will setup. From the back of each Poly Edge B30 phone there are exact model information that you should check. Although different phone models can have exactly the same requirements and... -
Page 3: Dhcp Server
factory default login details are username: admin and password: admin. Go to Status in left navigation menu. Click on System Status. Under Product Information section you can see Software Version field that contains information about firmware version. DHCP server Fully configured and operational DHCP server. PBXware version PBXware version 6.6.1... -
Page 4: Power Over Ethernet (Poe)
Do not unplug or remove power to the phone while it is updating firmware and configurations. Registering phone This chapter describes how to identify Poly Edge B30 phone model, requirements that must be met and how to register the phone using manual configuration or auto provisioning. The following topics are covered:... -
Page 5: Manual Configuration
Login to PBXware with your e-mail address and password. Navigate to Settings:UAD. Make sure Poly Edge B30 UAD is enabled. To check the UAD status click on the edit icon corresponding to your Poly Edge B30 phone. Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes. - Page 6 Department to which extension will belong to. Example: Sales. Click on the Save button. Registering Phone This chapter describes how to register Poly Edge B30 phone using Hostname or IP Address. The following topics are covered: Hostname or IP Address...
-
Page 7: Auto Provisioning
Enter the Hostname or IP Address of the PBXware. - Example for Hostname: voip.bicomsystems.com - Example for IP Address: 192.168.1.10 Registrar Server Enter the Hostname or IP Address of the PBXware. - Example for Hostname: voip.bicomsystems.com - Example for IP Address: 192.168.1.10 Click on Voice Services and select SP1 Service. - Page 8 UAD settings. Navigate to Settings:UAD. Make sure Poly Edge B30 UAD is enabled. To check the UAD status click on the edit icon corresponding to your Poly Edge B30 phone. Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
- Page 9 Click on the Save button. Registering Phone This chapter describes how to register Poly Edge B30 phone using TFTP, HTTP or HTTPS. TFTP, HTTP or HTTPS Open a new browser window and enter your phone IP address, e.g. http://192.168.1.22.
-
Page 10: Using Tls
Example for Hostname using HTTPS: https://username:password@abc.bicomsystems.com/prov/phone$mac.cf g,tls-profile=1 Example for IP Address using HTTP: http://username:password@192.168.1.10/prov/phone$mac.cfg Example for IP Address using HTTPS: https://username:password@192.168.1.10/prov/phone$mac.cfg,tls-profi le=1 Replace username and password with Auto Provisioning username and password. Example for Hostname using TFTP: tftp://voip.bicomsystems.com/phone$mac.cfg Example for IP Address: tftp://192.168.1.10/phone$mac.cfg Click on Submit button then Reboot button. -
Page 11: Configure Blf
Configure BLF Extension Settings This section describes how to configure BLF (Busy Lamp Field) for Poly Edge B30. Log in to the PBXware's web administration interface. Open a new browser window and enter the IP address in order to access the PBXware's web administration login page. -
Page 12: Additional Configuration Template
Click Save. Additional Configuration Template If you want to include some additional UAD configuration for Poly Edge B30, just add fields to User Agent General Auto Provisioning Template in Settings -> UAD -> Poly Edge B30 menu, or add them directly to the Extension in UAD Auto Provisioning Template section.
Need help?
Do you have a question about the Edge B30 and is the answer not in the manual?
Questions and answers