Trademarks KONICA MINOLTA, the KONICA MINOLTA logo and PageScope are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING SOLU- TIONS U.S.A., INC. All other trademarks and registered trademarks are the property of their respective owners.
Page 3
This package contains the following materials provided by Konica Minolta Business Technolo- gies, Inc. (KMBT): software included as part of the printing system, the digitally-encoded machine-readable outline data encoded in the special format and in the encrypted form (“Font Programs”), other software which runs on a computer system for use in conjunction with the Printing Software (“Host Software”), and related explanatory written materials (“Documenta-...
11. Notice to Government End Users: The Software is a “commercial item,” as that term is defined at 48 C.F.R.2.101, consisting of “commercial computer software” and “commercial computer software documentation,” as such terms are used in 48 C.F.R. 12.212. Consis- tent with 48 C.F.R.
Page 5
4. DISCLAIMER OF WARRANTY Adobe licenses the Software to you on an “AS IS” basis. Adobe makes no representation as to the adequacy of the Software for any particular pur- pose or to produce any particular result. Adobe shall not be liable for loss or damage aris- ing out of this Agreement or from the distribution or use of the Software or any other materials.
Page 6
“TOYO INK Standard Color on Coated paper” is compatible with “JAPAN COLOR”. Agreement 1. The reproduction of images on a printer or a monitor using this ICC Profile do not com- pletely match the TOYO INK Standard Color on Coated paper.
Contents 1 Introduction ... 1 Getting Acquainted with Your Printer 2 Space Requirements Printer Parts Front View 3 Rear View 4 Front View with Options 4 2 About the Software ... 5 Software Utilities CD-ROM 6 PostScript Drivers PCL Drivers...
Page 10
Layout Tab Cover Page Tab Overlay Tab Watermark Tab Quality Tab Version Tab Limitations on Printer Driver Functions Installed with Point and Print Using the Windows Me/98SE PPD File 20 Common Buttons OK 20 Cancel 20 Apply 20 Restore Defaults 20...
Page 11
4 Printer Control Panel and Configuration Menu ... 27 About the Control Panel 28 Control Panel Indicators and Keys Message Window Help Screens Configuration Menu Overview 32 Main Menu PROOF/PRINT MENU Printing/Deleting a Stored Job Entering a Password PRINT MENU...
Page 12
About Toner Cartridges Replacing a Toner Cartridge 128 Replacing a Imaging Unit 132 Replacing the Waste Toner Bottle Replacing the Backup Battery 8 Maintaining the Printer ...143 Maintaining the Printer 144 Cleaning the Printer 148 Exterior Media Rollers Cleaning the Media Feed Rollers (Manual Feed Tray) 149...
Page 13
Installing the Caster Base Banner Tray 229 Installing the Banner Tray A Appendix ... 233 Safety Specifications 234 Technical Specifications 234 Printer Consumable Life Expectancy Chart Our Concern for Environmental Protection 239 What is an ENERGY STAR product? 239 Contents...
Side View 100 mm (3.9") ! " The options appear shaded in the above illustrations. 966 mm (38.0") 650 mm (25.6") 577 mm (22.7") 437 mm (17.2") 603 mm (23.7") Getting Acquainted with Your Printer 100 mm (3.9") 100 mm (3.9")
The following drawings illustrate the parts of your printer referred to through- out this guide, so please take some time to become familiar with them. Front View 1—Control panel 2—Toner cartridge (Cyan, Magenta, Yellow) 3—Toner cartridge (Black) 4—Output tray 5—Top cover 6—Fuser unit...
2—Digital Camera Direct Print Port 3—10Base-T/100Base-TX/ 1000Base-T ethernet interface port 4—USB port 5—Parallel port 6—Filter 3 (Ozone filter) 7—Power connection 8—Option cassette connector 9—Ventilation grilles Front View with Options 1—Duplex option 2—Lower feeder units (Tray 3/4/5) Getting Acquainted with Your Printer...
Windows NT 4.0 ! " When using Windows Me/98SE, use the PPD file for Windows Me/ 98SE. See also “Displaying Windows Printer Driver Settings” on page ! " A specific PPD file has been prepared for applications (such as Page- Maker and CorelDRAW) that require that a PPD file be specified when printing.
Windows Server 2003/XP/2000/NT 4.0/Me/98SE Macintosh OS X/9 Linux ! " For details on the installation of the Windows printer drivers, refer to the magicolor 7450 Installation Guide on the Documentation CD-ROM. Utilities Utility Download Manager Crown Print Monitor for Windows...
Page 22
For details, refer to the magicolor 7450 Reference Guide on the Docu- mentation CD-ROM. Using the TCP/IP and IPX protocols, basic network printer settings can be specified. For details, refer to the PageScope Network Setup User Manual on the Software Utilities CD-ROM.
– Red Hat Linux 9.0, SuSE Linux 8.2 Free hard disk space – Approximately 20 MB of free hard disk space for the printer driver and Status Monitor – Approximately 128 MB of free hard disk space for image processing...
– (Windows Server 2003/XP) From the Start menu, choose Printers and Faxes to display the Printers and Faxes directory. Right-click the KONICA MINOLTA mc7450 PCL6 or KONICA MINOLTA mc7450 PS printer icon and choose Properties. – (Windows 2000/NT 4.0) From the Start menu, choose Settings and then Printers to display the Printers directory.
With Windows NT 4.0, right-click the KONICA MINOLTA mc7450 PCL6 printer icon or the KONICA MINOLTA mc7450 PS printer icon in the Printers directory, and then click Document Defaults. Skip to step 10. Select the General tab. Click Printing Preferences.
Choose the driver’s properties as follows: – From the Start menu, choose Settings and then Printers to display the Printers directory. Right-click the KONICA MINOLTA mc7450 PPD printer icon and choose Properties. Select the Device Options tab. Check that the installed options are correctly listed. If not, proceed with the next step.
From the Start menu, choose Settings and then Printers to display the Printers directory. Right-click the KONICA MINOLTA mc7450 PCL6 or KONICA MINOLTA mc7450 PS printer icon or KONICA MINOLTA mc7450 PPD printer icon and choose Delete. Click Yes to verify the driver deletion.
Printers directory. Display the printer driver settings: # Windows 2000—Right-click the KONICA MINOLTA mc7450 PCL6 or KONICA MINOLTA mc7450 PS printer icon and choose Printer Prop- erties. # Windows NT 4.0—Right-click the KONICA MINOLTA mc7450 PCL6 or KONICA MINOLTA mc7450 PS printer icon and choose Document Defaults.
Drivers ! " When using KONICA MINOLTA mc7450 PCL6 printer driver on Win- dows Me/98SE, a tab for specifying printer settings appears in the dia- log box. For details on using KONICA MINOLTA mc7450 PPD on Windows Me/98SE, refer to “Using the Windows Me/98SE PPD File” on page Common Buttons The buttons described below appear on each tab.
This button does not appear on the Advanced, Watermark, Quality and Version tabs. Printer View Click the button to display an image of the printer (with all installed options) in the figure area. ! " This button does not appear on the Advanced and Version tabs.
Specify the number of copies Turn on/off job collation Save a print job on the printer and print it later (Job Retention) Save a confidential job on the printer and protect it with a password Print a single copy for proofing...
Be sure to use overlays with print jobs with a media size and orienta- tion that matches the overlay form. In addition, if settings have been specified for “N-up” or “Booklet” in the printer driver, the overlay form cannot be adjusted to match the specified settings. The Overlay Tab allows you to...
*JOBNAME, USERNAME, and HOSTNAME output of PJL When using these operating system combinations, install the printer driver on the client with a local connection, and then specify the shared printer installed on the server as the connection. Using the Postscript and PCL Printer Drivers...
! " A tab for specifying printer settings appears in the dialog box. Common Buttons The buttons described below appear on each tab. Click to exit the Properties dialog box, saving any changes made. Cancel Click to exit the Properties dialog box without saving any changes made.
View information about the printer driver Graphics Tab The Graphics Tab allows you to Specify the resolution for the printout Specify the printer color settings Select the halftone setting Switch between color and monochrome printing Print a mirror image Scale (expand/reduce) documents...
The Status Monitor shows information about the current status of the printer. The Status Monitor can be installed from the Software Utilities CD-ROM. For details on the installation, refer to the magicolor 7450 Reference Guide on the Documentation CD-ROM. Operating Environment The Status Monitor can be used on computers running Windows XP/ Server 2003/2000/Me/98SE/NT 4.0 connected to the printer using an Ether-...
The address of the page that is accessed can be spec- ified from the Advanced Options dialog box. Printer Alerts—Displays text messages that alert you of conditions such as low toner. Recovery Instructions—Provides you with explanations of what you need to do in order to correct problems and recover from error conditions.
The control panel, located on the top of the printer, allows you to direct the printer’s operation. In addition, it displays the current status of the printer, including any condition that needs your attention. Control Panel Indicators and Keys Indicator...
Page 43
About the Control Panel Function # Cancels the currently displayed menu or menu choice # Allows you to cancel one or all print jobs that are currently being printed or processed: 1. Press the Cancel key. 2. Press the Up or Down keys to select either CURRENT JOB ALL JOBS 3.
Message Window The current status of the printer, the amount of toner remaining, and any error messages can be viewed from the message window. Details The current status of the printer is displayed. # If the operator or service representative must be called, the sym- # If a warning occurs, the symbol the window.
Help Screens The help screens appear when the Down key is pressed after an error occured, such as a media misfeed, so that the error can be corrected. About the Control Panel...
The magicolor 7450 configuration menu accessible from the control panel is structured as shown below. Main Menu READY PROOF/ PRINT MENU PRINT MENU PAPER MENU QUALITY MENU CAMERA DIRECT** INTERFACE MENU SYS DEFAULT MENU MAINTENANCE MENU SERVICE MENU ! "...
This menu item appears only if an optional hard disk is installed. With this menu item, print jobs that were set to be saved on the hard disk by using Job Retention on the Basic tab of the printer driver can be printed or deleted.
If the print job selected in the screen for entering the password appears. Follow the procedure described below to type in the four-digit password specified from the printer driver. Press the Up and Down keys to increase or decrease the first digit of the password.
Page 49
Press the Up and Down keys to increase or decrease the second digit of the password. Continue these steps until all four digits of the password are specified. Press the Menu/Select key. PRINT/DELETE ! " If an incorrect password is entered, the screen for entering the password appears again.
With this menu, printer information, such as the configuration page and the demo page, can be printed. PRINT MENU CONFIGURATION DEMO PAGE STATISTICS PAGE FONT LIST MENU MAP DIRECTORY LIST ! " * This menu item appears only if an optional hard disk is installed.
Page 51
FONT LIST MENU MAP DIRECTORY LIST Configuration Menu Overview Settings POST PRINT/CANCEL SCRIPT Prints a PostScript font list. Settings PRINT/CANCEL Prints a PCL font list. Settings PRINT/CANCEL Prints a menu map. Settings PRINT/CANCEL Prints a directory list of the hard disk.
With this menu, the media used for printing can be managed. PAPER MENU PAPER SOURCE DUPLEX COPIES COLLATE DEFAULT TRAY TRAY 1 PAPER SIZE CUSTOM SIZE PAPER TYPE TRAY 2 PAPER SIZE CUSTOM SIZE PAPER TYPE SIZE SETTING TRAY 3 PAPER SIZE PAPER TYPE TRAY 4...
Page 53
* This menu item appears only if the optional duplex unit is installed. ** This menu item appears only if an optional hard disk is installed. *** These menu items appear only if corresponding optional lower feeder unit is installed. ****This menu item appears only when you select CUSTOM from the TRAY 1/PAPER SIZE menu.
Page 54
! " Selecting “ANY” is considered the same as if media with the size specified from the printer driver is loaded, and the pages are printed without the actual media size selected. Be sure to load media with the specified size.
Page 55
Tray 1. ! " Selecting “ANY” is considered the same as if media with the type specified from the printer driver is loaded, and the pages are printed without the actual media type selected. Be sure to load media with the specified type.
Page 56
Specify the media size when CUSTOM custom-sized media is loaded into Tray 1. SIZE The setting units can be switched between millimeters and inches with the SYSTEM-PAPER-UNIT OF MEASURE Setting range for MILLIMETERS # For (The default is # For INCHES (The default is Setting range for...
Page 57
This setting is used to link a tray setting specified from a third-party printer driver with trays on this printer. Settings LOGICAL TRAY 0-9 The physical tray assigned to each logical tray can be specified.
Page 58
LONG EDGE the media for long-edge binding. SHORT EDGE of the media for short-edge binding. The setting specified in the printer driver overrides this menu setting. Settings COPIES Specify the number of copies to be printed. The setting specified in the printer driver overrides this menu setting.
With this menu, settings for the print quality can be specified. QUALITY MENU COLOR MODE BRIGHTNESS PCL SETTING PS SETTING Configuration Menu Overview CONTRAST IMAGE PRINTING RGB SOURCE RGB INTENT RGB GRAY HALFTONE TEXT PRINTING RGB SOURCE GRAPHICS RGB INTENT PRINTING RGB GRAY HALFTONE...
Page 60
CALIBRATION COLOR SEPARATION TEXT PRINTING RGB SOURCE RGB INTENT RGB GRAY DESTINATION PROF HALFTONE GRAPHICS RGB SOURCE PRINTING RGB INTENT RGB GRAY DESTINATION PROF HALFTONE SIMULATION SIMULATION PROF TONE CALIBRATION SIMULATION INTENT AIDC PROCESS CMYK GRAY CMYK DENSITY Configuration Menu Overview...
Page 61
All factory default values are shown in bold. Settings COLOR MODE and white. Settings BRIGHT- NESS The brightness of the printed image can be adjusted. CONTRAST SETTING IMAGE PRINTING Configuration Menu Overview COLOR/GRAYSCALE COLOR is selected, the pages are printed in full color. GRAYSCALE is selected, the pages are printed in black -15%/-10%/-5%/0%/+5%/+10%/...
Page 62
Settings COMPOSITE GRAY BLACK/BLACK AND GRAY/ BLACK ONLY Specify how black and grays are reproduced in RGB image data. COMPOSITE BLACK selected, black is reproduced using the CMYK colors. BLACK AND GRAY selected, black and gray are reproduced using black only. BLACK ONLY black is reproduced using only black.
Page 63
TEXT PRINTING Configuration Menu Overview Settings DEVICE COLOR/ SOURCE sRGB Specify the color space for RGB text data. DEVICE COLOR selected, no color space is specified. If RGB source profiles are downloaded with the Download Manager, they are available from the list of settings. Settings VIVID/ INTENT...
Page 64
GRAPHICS PRINTING Settings HALF- LINE ART/ TONE DETAIL/SMOOTH Select how halftones are reproduced. LINE ART halftones are reproduced with high precision. DETAIL is selected, halftones are reproduced with detail. SMOOTH is selected, halftones are reproduced with smoothness. Settings AS IMAGE/AS TEXT Specify the color setting for graphics.
Page 65
IMAGE SETTINGS PRINTING Configuration Menu Overview Settings DEVICE COLOR/ SOURCE sRGB/ AppleRGB/ AdobeRGB1998/ ColorMatchRGB BlueAdjustRGB Specify the color space for RGB image data. DEVICE COLOR selected, no color space is specified. If RGB source profiles are downloaded with the Download Manager, they are available from the list of settings.
Page 66
NATION Specify the destination profile. PROF AUTO is selected, a destination profile that the printer automatically adapts is selected based on a combination of the specified color matching, halftones and other profiles. If destination profiles are downloaded with the Download Manager, they are available from the list of settings.
Page 67
TEXT PRINTING Configuration Menu Overview Settings HALF- LINE ART/ TONE DETAIL/SMOOTH Select how halftones are reproduced. LINE ART halftones are reproduced with high precision. DETAIL is selected, halftones are reproduced with detail. SMOOTH is selected, halftones are reproduced with smoothness. Settings DEVICE COLOR/ SOURCE...
Page 68
Settings VIVID/ INTENT PHOTOGRAPHIC/ RELATIVE COLOR/ ABSOLUTE COLOR Specify the characteristic applied when converting RGB text data to CMYK data. VIVID is selected, a vivid output is produced. PHOTOGRAPHIC selected, a brighter output is produced. RELATIVE COLOR selected, relative color is applied to the RGB source profile.
Page 69
NATION Specify the destination profile. PROF AUTO is selected, a destination profile that the printer automatically adapts is selected based on a combination of the specified color matching, halftones and other profiles. If destination profiles are downloaded with the Download Manager, they are available from the list of settings.
Page 70
GRAPHICS PRINTING Settings DEVICE COLOR/ SOURCE sRGB/ AppleRGB/ AdobeRGB1998/ ColorMatchRGB BlueAdjustRGB Specify the color space for RGB image data. DEVICE COLOR selected, no color space is specified. If RGB source profiles are downloaded with the Download Manager, they are available from the list of settings.
Page 71
NATION Specify the destination profile. PROF AUTO is selected, a destination profile that the printer automatically adapts is selected based on a combination of the specified color matching, halftones and other profiles. If destination profiles are downloaded with the Download Manager, they are available from the list of settings.
Page 72
SIMULATION Settings SIMU- NONE/SWOP/ LATION Euroscale/ PROF CommercialPre ss/TOYO/DIC Specify the simulation profile. NONE is selected, no simulation profile is specified. If simulation profiles are downloaded with the Download Manager, they are available from the list of settings. Settings SIMU- RELATIVE LATION COLOR/...
Page 73
CALIBRA- TONE TION CALIBRATION AIDC PROCESS Configuration Menu Overview Settings CMYK COMPOSITE GRAY BLACK/BLACK AND GRAY/ BLACK ONLY Specify how black and grays are reproduced using the four CMYK colors. COMPOSITE BLACK selected, black is reproduced using the CMYK colors. BLACK AND GRAY selected, black and gray are reproduced using black only.
Page 74
CMYK DENSITY Settings COLOR SEPARA- TION contents of a color page is separated into the color pages for yellow, magenta, cyan and black, and each is printed with black gradations as individual pages. The printing order is yellow, magenta, cyan, then black. normal color separation is performed.
This menu item appears when ENABLE set to With this menu, settings for “camera direct” function can be specified. ! " These settings are overridden by any settings configured within the digital camera. For details on camera direct, refer to “Camera Direct” on page 84. CAMERA DIRECT PAPER SOURCE LAYOUT...
Page 76
All factory default values are shown in bold. Settings PAPER SOURCE The tray that is used can be specified. ! " Settings LAYOUT Specify the number of images printed on a single sheet of media. When set to sheet of media. Settings PAPER MARGIN...
Page 77
RGB GRAY HALFTONE Configuration Menu Overview Settings COMPOSITE BLACK/BLACK AND GRAY/BLACK ONLY Specify how black and grays are reproduced in RGB image data. COMPOSITE BLACK reproduced using the CMYK colors. BLACK AND GRAY is selected, black and gray are reproduced using black only. BLACK ONLY is selected, black is reproduced using only black.
With this menu, interface settings can be specified. ! " Restart the printer after changing settings in the INTERFACE MENU JOB TIMEOUT ETHERNET CAMERA DIRECT ETHERNET TCP/IP ENABLE IP ADDRESS SUBNET MASK DEFAULT GATEWAY DHCP/BOOTP TELNET NETWARE ENABLE APPLETALK ENABLE...
TCP/IP is enabled. is selected, TCP/IP is disabled. Setting 000.000.000.000 ADDRESS Set the IP address for this printer on the network. Use the Up, Down, Left, and Right keys to specify the value. If the IP address is manually specified,...
Page 80
NETWARE ENABLE APPLE TALK SPEED/ DUPLEX CAMERA Settings DIRECT Select whether to enable or disable camera direct printing. ENABLE DISABLE Settings TELNET ENABLE/DISABLE Select whether to enable or disable Telnet transmissions. When ENABLE transmissions are enabled. DISABLE When transmissions are disabled. Settings YES/NO is selected, NetWare is enabled.
With this menu, settings can be specified to adjust the operation of the printer, such as the display language of the message window and the time until the machine enters Energy Saver mode. SYS DEFAULT MENU LANGUAGE EMULATION PAPER STARTUP...
Page 82
RESTORE DEFAULTS ENABLE WARNING IMAGING UNIT LIFE CHANGE PASSWORD LOCK PANEL DATE (xx.xx.xx) TIME USER AREA ONLY RESTORE NETWORK RESTORE PRINTER RESTORE ALL PAPER EMPTY TRAY1 TONER LOW TRAY2 I-UNIT LOW TRAY3 TRAY4 TRAY5 Configuration Menu Overview **** **** ****...
Page 83
KOREAN/SIMPLIFIED CHINESE/ TRADITIONAL CHINESE/DUTCH Settings AUTO/POSTSCRIPT/PCL Specify the printer emulation language. AUTO is selected, the printer automatically selects the printer emulation language from the data stream. Settings WAIT 0-300 TIME Specify the time until an error is determined to be a PostScript error.
Page 84
Settings CR/LF CR=CR LF=LF/CR=CRLF MAP- LF=LF/CR=CR PING LF=LFCR/CR=CRLF LF=LFCR Select the definitions of the CR/LF codes in the PCL language. Settings LINES 5-60-128 Specify the number of lines per page in PAGE the PCL language. Settings FONT FONT SOURCE NUMBER Specify the default font in the PCL language.
Page 85
PAPER DEFAULT PAPER Configuration Menu Overview Settings LETTER /11x17/LEGAL/ PAPER SIZE EXECUTIVE/A3WIDE/A3/ A4 /A5/A6/B4(JIS)/ B5(JIS)/B6(JIS)/GOVT LETTER/STATEMENT/ FOLIO/SP FOLIO/UK QUARTO/FOOLSCAP/GOVT LEGAL/16K/12x18/ 11x14/4x6/D8K/KAI 8/ KAI 16/KAI 32/ENV C5/ENV C6/ENV DL/ENV MONARCH/ENV CHOU#3/ ENV CHOU#4/B5(ISO)/ ENV #10/ENV YOU#4/ JPOST/JPOST-D/CUSTOM Select the size of media that is normally used.
Page 86
The default setting for North America is INCHES . The default setting for all other MILLIMETERS regions is Settings ON/OFF Select whether or not a startup page is printed when the printer is turned on. Configuration Menu Overview is selected, the media size...
Page 87
Energy Saver mode and begin operating. LIGHT SLEEP be used even if the printer has entered Energy Saver mode. In addition, if the printer receives print data, the printer begins operating immediately.
Page 88
In order to lock the control panel, be sure to specify a password other than 0000 Specify the date for the printer's internal clock. The date for Asia and China is set in the order year, YY.MM.DD month, then day (...
Page 89
TONER I-UNIT Configuration Menu Overview Initialize the user area of the hard disk. When this menu item is selected, the printer is automatically restarted. Initialize the hard disk. When this menu item is selected, the printer is automatically restarted. Initialize the card. When this menu is selected, the printer is automatically restarted.
Page 90
Settings IMAG- STOP UNIT life for the imaging unit is detected. LIFE CONTINUE the service life for the imaging unit is detected. STOP/CONTINUE is selected, printing stops when the end of the service is selected, printing continues even if the end of Configuration Menu Overview...
With this menu, maintenance on this printer can be performed. In order to use this menu, the administrator password must be entered. MAINTENANCE MENU PRINT MENU ALIGNMENT Configuration Menu Overview EVENT LOG HALFTONE 64 CYAN/MAGENTA/ YELLOW/BLACK 64 HALFTONE 128 CYAN/MAGENTA/...
Page 92
! " All factory default values are shown in bold. PRINT EVENT MENU HALF- TONE HALF- TONE HALF- TONE GRADA- TION DUPLEX PASS IMG ADJ CYAN THICK MAGENTA YELLOW BLACK IMG ADJ BLACK FUSER LOOP Settings PRINT/CANCEL Prints the event log. Settings CYAN/ PRINT/CANCEL...
Page 93
ALIGN- MENT ADJUST MENT LEFT ADJUST MENT Configuration Menu Overview Settings PLAIN -30-0-30 PAPER When printing on plain paper, specify the size of the top margin. Settings THICK -30-0-30 When printing on thick paper 1, specify the size of the top margin. Settings THICK -30-0-30...
Page 94
LEFT DUPLEX TRANS- POWER Settings LEFT -30-0-30 When duplex printing on media in Tray 1, TRAY1 specify the size of the left margin. Settings LEFT -30-0-30 When duplex printing on media in Tray 2, TRAY2 specify the size of the left margin. Settings LEFT -30-0-30...
Page 95
Configuration Menu Overview Settings THICK When printing on thick 3 using simplex pass, correct the sec- ondary image transfer current. Settings POST- CARD When printing on postcard using simplex pass, correct the secondary image transfer current. Settings ENVELO When printing on envelope using simplex pass, correct the secondary image transfer current.
THICK BLACK FUSER LOOP SERVICE MENU With this menu, the service representative can adjust the printer and perform maintenance operations. This menu cannot be used by the user. Settings ENVE- LOPE When printing on envelope using duplex pass, correct the secondary image transfer cur- rent.
If a digital camera with PictBridge (1.0 or later) is connected to the printer through the Camera Direct Print port, images stored on the digital camera can be printed directly from the printer. ! " For details on using the digital camera, refer to your digital cameras manual.
Page 99
From the digital camera, specify the image that you wish to print and the desired number of copies. Start printing from the digital camera. Camera Direct...
CUSTOM (Tray2) 3.55 x 5.50 to 12.25 x 18.00 Notes: * LEF=Long Edge Feed, SEF=Short Edge Feed ! " For custom sizes, use the printer driver to specify the settings within the ranges shown in the above table. Media Size Inch 10.6 x 15.4...
Keep media on a flat, level surface in its original wrapper until it is time to load it. For a list of approved media, refer to printer.konicaminolta.com. Plain Paper (Recycled Paper)
Page 104
Cold-water-transfer paper Pressure sensitive Designed specifically for inkjet printers (such as superfine paper, glossy paper, glossy film, and postcards) Already printed on by another printer, copier, or fax machine Dusty Wet (or damp) ! " Keep media between 35% and 85% relative humidity. Toner does not adhere well to moist or wet paper.
Paper thicker than 90 g/m thick stock to ensure acceptable performance and to ensure that the image does not shift. Capacity Tray 1 (Manual Feed Tray) Tray 2 Tray 3/4/5 Orientation Tray 1 (Manual Feed Tray) Tray 2 Tray 3/4/5 Driver Thick 1 (91-150 g/m Media Type...
DO NOT use thick stock that is Mixed with any other media in Tray 1 (as this will cause printer misfeed- ing) Envelopes Print on the front (address) side only. Some parts of the envelope consist of three layers of paper—the front, back, and flap. Anything printed in these lay- ered regions may be lost or faded.
Page 107
Too rough of a surface Material that will melt, vaporize, offset, discolor, or emit dangerous fumes Been presealed Media Types...
A sheet of labels consists of a face sheet (the printing surface), adhesive, and a carrier sheet: The face sheet must follow the plain paper specification. The face sheet surface must cover the entire carrier sheet, and no adhe- sive should come through on the surface. You can print continuously with label sheets.
Are precut or perforated Shiny backed paper Letterhead Try printing your data on a sheet of plain paper first to check placement. Capacity Tray 1 (Manual Feed Tray) Tray 2 Tray 3/4/5 Orientation Tray 1 (Manual Feed Tray) Tray 2 Tray 3/4/5 Driver Letterhead...
! " Keep the printer path clean. Transparencies are especially sensitive to a dirty media path. If there are shadows on either the top or the bottom of the sheets, see chapter 8, “Maintaining the Printer” .
If you have problems feeding 20 sheets, try loading only 1–10 sheets at a time. Loading a large number of transparencies at one time may cause static buildup, thus causing feeding problems. Capacity Tray 1 (Manual Feed Tray) Tray 2 Tray 3/4/5 Orientation Tray 1 (Manual Feed...
Page 112
Glossy Media Type Weight 64–90 g/m² (17–24 lb) Duplexing Not supported DO NOT use glossy stock that is Mixed with any other media in Tray 1/2 (as this will cause printer misfeed- ing) Face down Face up — Media Types...
Top/Bottom edge of the media. Each media size has a specific imagea- ble area, the maximum area on which the printer can print clearly and without distortion. This area is subject to both hardware limits (the physical media size and the...
Do not fan transparencies. Note Although this printer was designed for printing on a wide range of media types, it is not intended to print exclusively on a single media type except plain paper. Continuous printing on media other than plain paper (such as envelopes, labels, thick stock, or transparencies) may adversely affect print quality or reduce engine life.
Page 115
Slide the media guides to pro- vide more space between them. Load the paper face down in the tray. ! " Do not load paper above the line. Up to 100 sheets (80 g/m paper can be loaded into the tray at one time. Loading Media [22 lb]) of plain...
See also “PAPER SIZE” on page 39. ! " When printing from Tray 1 with the corresponding Paper Source setting selected in the printer driver (Manual Feed), it is not neces- sary to change the configuration menu setting. Other Media...
Pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Push up the top cover. Loading Media...
Page 118
Push down the left and right release levers M2 to the position. Close the top cover. Loading Media...
Page 119
Close the right side cover. Open Tray 1. Slide the media guides to pro- vide more space between them. Loading Media...
Page 120
Load the envelopes in the tray face down with the flaps toward the outside of the tray. ! " Before loading enve- lopes, press them down to make sure that all air is removed, and make sure that the flaps are com- pletely open and pressed flat;...
See also “PAPER TYPE” on page 41. ! " When printing from Tray 1 with the corresponding Paper Source setting selected in the printer driver (Manual Feed), it is not neces- sary to change the configuration menu setting. Loading Label Sheets/Postcards/Thick Stock/Glossy Stock and Transparencies Open Tray 1.
Page 122
See also “PAPER TYPE” on page 41. ! " When printing from Tray 1 with the corresponding Paper Source setting selected in the printer driver (Manual Feed), it is not neces- sary to change the configuration menu setting. in the...
Paper up to 1200 mm long can be loaded into the bypass tray and printed one at a time. ! " If the optional banner tray is installed, up to 10 sheets can be printed continuously. For details, refer to “Banner Tray” on page 229. Open Tray 1.
Page 124
See also “CUSTOM SIZE” on page 40. ! " When printing from Tray 1 with the corresponding Paper Source setting selected in the printer driver (Manual Feed), it is not neces- sary to change the configuration menu setting. Loading Media...
Loading Media Pull out Tray 2. Press down the media pressure plate to lock it into place. Note Do not touch the media feed roller’s surface. This could lower image quality. Loading Media...
Page 126
Slide the media guides to pro- vide more space between them. ! " To load media of a non-standard size, first load the media and then adjust the media guides to the size of the loaded media. For media exceeding A3 size, adjust the guides as shown in the illustration.
Page 127
Do not load above the M mark. Up to 250 sheets (80 g/m paper can be loaded into the tray at one time. A maximum of 50 sheets of thick paper, label sheets, letterhead pages, postcards, overhead pro- jector transparencies or glossy paper can be loaded.
Pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Open the top cover. Loading Media...
Page 129
Push down the left and right release levers M2 to the position. Close the top cover. Loading Media...
Page 130
Close the right side cover. Note Since a media misfeed or decreased print quality may occur, be sure to return the levers on the fuser unit to the setting for plain paper before printing on media other than envelopes. Loading Media...
Loading Plain Paper Pull out Tray 3/4/5. Slide the media guides to pro- vide more space between them. Loading Media...
Page 132
Load the paper face up in the tray. ! " Do not load above the M mark. Up to 500 sheets (80 g/m paper can be loaded into the tray at one time. Slide the media guides against the edges of the paper. [22 lb]) of plain Loading Media...
Page 133
Close Tray 3 (4/5). Select TRAY3 TRAY4 TRAY5 /PAPER TYPE in the configura- tion menu, and then select the setting for the type of paper that is loaded. See also “PAPER TYPE” on page 43. Loading Media...
Duplexing envelopes, labels, postcards, glossy stock or transparencies is not supported. How do I autoduplex? You should verify that the duplex option is physically installed on the printer to successfully duplex the job. Check your application to determine how to set your margins for duplex printing.
Page 135
In addition, if “N-up” has been set to “Booklet”, autoduplex printing is per- formed. The following Order settings are available when “Booklet” is selected. Load plain paper or thick paper into the tray. From the printer driver, specify double-sided printing (Layout tab in Win- dows). Click OK. ! "...
All printed media is output to the face-down output tray on top of the printer. This tray has a capacity of approximately 350 sheets (A4/Letter) of 80 g/m (22 lb) paper. ! " If the media is stacked too high in the output tray, your printer may experience media misfeeds, excessive media curl, or static buildup.
How do I store media? Keep media on a flat, level surface in its original wrapper until it is time to load it. Media that has been stored for a long time out of its packaging may dry up too much and cause misfeeding. If media has been removed from its wrapper, place it in its original pack- aging and store in a cool, dark place on a level surface.
Handle the toner cartridges carefully to avoid spilling toner inside the printer or on yourself. ! " Install only new toner cartridges in your printer. If a used toner car- tridge is installed, the indicator message will not clear and the supplies status in the Status Monitor will not be updated.
Page 141
When replacing a toner cartridge, refer to the following table. For optimum print quality and performance, use only approved KONICA MINOLTA toner cartridges for your specific printer type, as listed in the table below. You can find your printer type and the toner cartridge part numbers on the consum- ables reorder label inside the front cover your printer.
Check the message window to see which color of toner is empty. Remove the air filter from the printer, and then slide the new filter into the printer until it snaps into place. ! " It is necessary to replace...
Page 143
Open the printer’s front cover. Pull up the locking tab of the empty toner cartridge to unlock it. Pull out the toner cartridge as far as possible, and then pull it up to remove it. Note Dispose of the used toner cartridge according to your local regulations.
Page 144
Shake the cartridge to distribute the toner. Align the toner cartridge with the slots in the machine, and then insert the cartridge until the lock- ing tab locks into place. Close the front cover. ! " If the toner cartridge is not fully inserted, the front cover cannot be closed.
Page 145
! " The printer must complete a 75-second calibration cycle after the toner cartridge has been replaced. If you open the front cover before the message READY appears, the printer stops and repeats the calibration cycle. Replacing Consumables...
When replacing a imaging unit, refer to the following table. For optimum print quality and performance, use only approved KONICA MINOLTA imaging units for your specific printer type, as listed in the table below. You can find your printer type and the imaging unit part numbers on the consumables reorder label inside the front cover your printer.
Page 147
Open the printer’s front cover. Press down the area marked “Push” on the imaging unit to be replaced, and then slide the unit all the way out of the printer. ! " Dispose of the used imaging unit according to your local regula- tions.
Page 148
In order to prevent toner from spilling, leave the imaging unit in the bag until step 5 is being performed. Hold the imaging unit with both hands, and then shake it twice as shown in the illustration. ! " Do not grab the bottom of the bag;...
Page 149
Remove the cover on the end of the imaging unit. While supporting the imaging unit from the bottom, insert it into the printer. At this time, make sure that the imaging unit is the same color as the imaging unit compartment.
Page 150
! " If the imaging unit is not fully inserted, the front cofer cannot be closed. ! " The printer must com- plete a 75-second cali- bration cycle after the toner cartridge has been replaced. If you open the front cover before the...
Open the printer’s front cover. Remove the dust filter, and then insert the new dust filter included with the waste toner bottle. Push the waste toner release lever. Replacing Consumables appears in the message window. The printer WASTE TONER...
Page 152
Dispose of the waste toner bottle. Note Dispose of the used waste toner bottle according to your local regulations. Do not burn the waste toner bottle. Prepare a new waste toner bottle. Slide the waste toner bottle all the way into the printer. Replacing Consumables...
Replacing the Backup Battery If the backup battery is dead, the printer’s date and time cannot be retained. Follow the procedure described below to replace the backup battery. ! " Only CR2032 3V Lithium coin battery can be used.
Page 154
Using a coin, remove the screw. Then, remove the left cover. Remove the backup battery. Replacing Consumables...
Page 155
When inserting the new backup battery, be sure that the + side faces upside. Attach the left cover. Reconnect all interface cables. Reconnect the power cord, and turn on the printer. DATE on the and use TIME time. Replacing Consumables...
Never use sharp or rough implements, such as wire or plastic cleaning pads. Always close the printer’s covers gently. Never subject the printer to vibra- tion. Do not cover the printer immediately after using it. Turn it off and wait until it cools down. Maintaining the Printer...
Page 159
Do not leave the printer’s covers open for any length of time, especially in well-lit places; light may damage the imaging units. Do not open the printer during printing. Do not tap media stacks on the printer. Do not lubricate or disassemble the printer.
Page 160
Make sure any parts removed during cleaning are replaced before you plug in the printer. If the printer is not to be used for two weeks or more (not turned on), lower the left and right M2 release levers to the position for envelopes.
Page 161
! " Before using the printer again, be sure to return the levers to the position for normal printing. If media other than enve- lopes are printed without the levers returned to their normal positions, decreased print quality may result.
Cleaning the Printer CAUTION Be sure to turn off the printer and unplug the power cord before cleaning. Exterior Control Panel Ventilation Grill Printer Exterior Cleaning the Printer...
The accumulation of paper dust and other debris on the media rollers can cause media-feeding problems. Cleaning the Media Feed Rollers (Manual Feed Tray) Open Tray 1. Clean the media feed rollers by wiping them with a soft, dry cloth. Close the tray. Cleaning the Printer...
Tray 3/4/5. ! " Before opening the right side cover of Tray 3/4/5, fold up Tray 1. Clean the media transfer rollers by wiping them with a soft, dry cloth. Close the right side cover of Tray 3/4/5. Cleaning the Printer...
This printer is constructed with four laser lenses. Clean all lenses as described below. The laser lens cleaning tool should be attached to the inside of the front cover. Open the printer’s front cover and remove the cleaning tool from the machine's front cover.
Page 168
Close the front cover. Cleaning the Printer...
Solving other problems Solving problems with printing quality Status, error, and service messages Printing a Configuration Page Print a configuration page to verify the printer is printing correctly, or to check the printer configuration. Press Key (once) Until Display Reads...
Media matches the printer specifications. Media is flat, especially on the leading edge. The printer is on a hard, flat, level surface. You store media in a dry location away from moisture and humidity. You remove transparencies from the output tray immediately after printing to avoid static buildup.
Understanding the printer’s media path will help you locate media misfeeds. 1 Toner cartridge 2 Transfer belt unit 3 Imaging unit 4 Laser 5 Tray 2 6 Tray 3 (optional) 7 Tray 4 (optional) 8 Tray 5 (optional) 9 Fuser unit...
To avoid damage, always remove misfed media gently, without tearing it. Any piece of media left in the printer, whether large or small, can obstruct the media path and cause further misfeeds. Do not reload media that has misfed. Note The image is not fixed on the media before the fusing process.
Media Misfeed Message PAPER JAM TRAY2 PAPER JAM TRAY3 PAPER JAM TRAY4 PAPER JAM TRAY5 PAPER JAM DUPLEX1 PAPER JAM DUPLEX2 PAPER JAM FUSER/EXIT PAPER JAM TRAY1 PAPER JAM SECOND TRANS PAPER JAM VERTICAL TRANS ! " If the message for media misfeeds in the transfer roller section of the right side covers for Tray 3 and/or Tray 4 and/or Tray 5.
Pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Carefully pull out the misfed media. Clearing Media Misfeeds...
Page 176
CAUTION The area around the fuser unit is extremely hot. Touching anything other than the indicated levers and dials may result in burns. If you get burned, immediately cool the skin under cold water, and then seek professional medical attention. Note Decreased print quality may result if the surface of the image...
Page 177
Close the right side cover. Pull out Tray 2, and then remove all media from the tray. Fan the media you removed and then align it well. ! " If transparencies are loaded, do not fan them; otherwise, static electricity may be produced, resulting in another media misfeed. Clearing Media Misfeeds...
Page 178
Load the media face up in Tray 2. ! " Make sure that the media is flat. ! " Do not load media above the M mark. ! " Slide the media guides against the edges of the media. Close Tray 2. Clearing Media Misfeeds...
Open the right side cover of Tray 3 (4/5). ! " Before opening the right side cover of Tray 3 (4/5), fold up Tray 1. Carefully pull out the misfed media. Close the right side cover of Tray 3 (4/5). Clearing Media Misfeeds...
Page 180
Pull out Tray 3 (4/5), and then remove all media from the tray. Fan the media you removed and then align it well. Load the media face up in Tray 3 (4/5). ! " Make sure that the media is flat. ! "...
Pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Push up the top cover. Carefully pull out the misfed media. Clearing Media Misfeeds...
Page 183
CAUTION The area around the fuser unit is extremely hot. Touching anything other than the indicated levers and dials may result in burns. If you get burned, immediately cool the skin under cold water, and then seek professional medical attention. Note Decreased print quality may result if the surface of the image...
Page 184
Push up the M2 release levers, and then pull inside cover M3 toward you to open it. ! " When pushing up the M2 release levers, push up both at the same time. ! " The M2 release levers will automatically return to their correct orig- inal positions when you close the top cover.
Page 185
After closing the top cover, close the right side cover. ! " Be sure to close the top cover before closing the right side cover. Close the right side cover. Clearing Media Misfeeds...
and Transfer Roller Remove all media from Tray 1. If the misfed media cannot be removed, pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Clearing Media Misfeeds...
Page 187
Carefully pull out the misfed media. CAUTION The area around the fuser unit is extremely hot. Touching anything other than the indicated levers and dials may result in burns. If you get burned, immediately cool the skin under cold water, and then seek professional medical attention.
Page 188
Note Decreased print quality may result if the surface of the image transfer belt or the transfer roller is touched. Be careful not to touch the surface of the image transfer belt or transfer roller. Close the right side cover. Clearing Media Misfeeds...
Recheck the media path and make sure that you have removed all of the misfed media. Use KONICA MINOLTA-approved media. See “Media Specifications” on page 88. Only plain paper, 60–90 g/m lb) and thick paper, 91–256 g/m 68.1 lb) can be autoduplexed.
Page 190
Load the envelopes in Tray 1 so the flaps are facing up. If the flaps are on the long edge, load the envelopes with the flaps toward the right of the printer. Solving Problems with Media Misfeeds...
Page 191
Remove the transparencies and load them in the tray one sheet at a time. Do not fan transparencies before load- ing them. Use KONICA MINOLTA-approved media. See “Media Specifications” on page Clean the media supply roller. For more details, refer to “Media Roll-...
There is a media misfeed. Solution Turn off the printer, confirm that the power cord is correctly plugged into the outlet, and then turn on the printer. Plug another electrical appliance into the outlet and see whether it operates properly.
Page 193
( DEFAULT MENU menu) Wait. No action needed. Add more memory. Install a correct KONICA MINOLTA toner cartridge approved for your spe- cific printer. INCOR- Check the toner cartridges. The image will not print if one or more cartridges are empty.
Page 194
Print the overlay file using a magicolor 7450 driver. Turn off the printer, confirm that the power cord is correctly plugged into the outlet, and then turn on the printer. Contact Technical Support with the error information.
Page 195
For N-up on multiple copies, choose Collate only in the Windows driver’s Paper Tab. Do not set collation in the application. Place the printer on a flat, hard, level surface. Remove the tray that you are printing from and reinsert it completely into the printer.
Page 196
Administrator password has a 6-char- acter minimum and a 16-character maximum. For details of the Page- Scope Web Connection administrator password, refer to the magicolor 7450 Reference Guide on the Documenta- tion CD-ROM. Remove the moist media and replace it with new, dry media.
Solving Problems with Printing Quality Solution Remove the imaging units and check for damage. If it is damaged, replace it. Select the proper setting in the printer driver to switch from transparencies to plain paper. Adjust the humidity for media storage.
Page 198
When printing envelopes, labels, post- cards, thick stock, or transparencies, specify the appropriate media type in the printer driver. Remove the imaging units and check them for damage. If one is damaged, replace it. Remove the imaging units and check them for damage.
Page 199
Solution Remove the toner cartridges and check them for damage. If one is dam- aged, replace it. Place the printer on a flat, hard, level surface. Adjust the humidity in the media stor- age area. Remove the moist media and replace it with new, dry media.
Page 200
Symptom Cause There are One or more of the toner imaging units may be smudges or defective or installed residual incorrectly. images. There are The media transfer toner roller is dirty. smudges on the back side of the page The media path is (whether or dirty with toner.
Page 201
Remove the imaging unit with the color causing the abnormal image. Replace it with a new imaging unit. Place the printer on a flat, hard, level surface. Print several sheets and the excess toner should disappear. Remove the imaging units and check them for damage.
Page 202
If the problem is not resolved, even after all of the above have been per- formed, contact Technical Support with the error information. For contact information, refer to the magicolor 7450 General Information Guide. Solution Remove the imaging units and check them for damage.
Status, error, and service messages are displayed in the control panel mes- sage window. They provide information about your printer and help you locate many problems. When the condition associated with a displayed message has changed, the message is cleared from the window.
END OF LIFE NEAR FULL ILLEGAL INSTALLATION INCORRECT means... The printer is being restarted. The printer is warming up. means... The fuser unit has Contact Technical Sup- reached the end of its port with the error infor- life. mation. Printing does not stop immediately when this message appears.
Page 205
(AM, EU, AP or GC). See page 127. The X toner cartridge Install a is an unapproved KONICA MINOLTA toner type. cartridge of the appropri- ate type (AM, EU, AP or GC). See page 127. The memory card is Delete resources (fonts, nearly full.
Page 206
This message... PAPER EMPTY TRAY X I-UNIT END I-UNIT LOW means... Tray X (Tray 1, 2, 3, 4, Load media into the or 5) is empty. specified tray. (Appears when DEFAULT MENU/ ENABLE WARN- ING/PAPER EMPTY TRAY X is set to Tray X (Tray 2, 3, 4 or Correctly install the 5) is not correctly...
Page 207
This message... I-UNIT LIFE TONER EMPTY TONER LOW Status, Error, and Service Messages means... do this... Replace the imaging imaging unit unit. has reached the end of its life. If If CONTINUE was set, IMAGING UNIT instead of the Operator LIFE on the Call message “I-UNIT...
Page 208
The media size Use media of a size that cannot be detected can be detected by the automatically. printer. Otherwise, adjust the media guides in the tray to a position where the media size can be recognized. The waste toner bot- Prepare a new waste tle is nearly full.
If desired, hard disk is not install a hard disk. installed. Tray 1 was specified Load the correct media with the printer driver into Tray 1. as Manual Feed for printing, but Tray 1 is empty. The Paper Source in...
Page 210
PAPER/ when PAPER SOURCE/ TRAY CHAINING is set.) The media size/type Load the correct media set in the printer size and type. driver is different from the size/type of media loaded (Appears PAPER/ when PAPER SOURCE/ TRAY CHAINING is set.)
This message... PAPER JAM DUPLEX1 PAPER JAM DUPLEX2 PAPER JAM FUSER/EXIT PAPER JAM SECOND TRANS PAPER JAM TRAY1 PAPER JAM TRAYX PAPER JAM VERTICAL TRANS I-UNIT END REPLACE I-UNIT LIFE REPLACE Status, Error, and Service Messages means... do this... Media has misfed in Press the Down key to the duplex option.
Page 212
The X (Tray 1, 2, 3, 4 Load the correct media or 5) was specified into the specified tray. with the printer driver for printing, but Tray X is empty. This mes- sage appears when PAPER/PAPER SOURCE/TRAY...
Page 213
REPLACE BOTTLE Status, Error, and Service Messages means... do this... The media type set in Load the correct media the printer driver is type into the specified different from the type tray. of media loaded. The waste toner Install a new waste toner bottle is full.
These messages indicate a more serious error that can only be corrected by a customer service engineer. If one of these messages appears, turn the printer off, then turn it on again. If the problem persists, contact your local vendor or authorized service provider.
Note Use of accessories not manufactured or supported by KONICA MINOLTA will void your warranty. ! " This chapter provides information about the following accessories. Dual In-Line Memory Module (DIMM) Duplex Option Lower Feeder Unit (Tray 3/4/5) Hard Disk CompactFlash...
Turn off all power switches first. If an antistatic wrist strap is provided in your printer option kit, attach one end of it to your wrist and the other end to the bare metal chassis on the back of your printer. Never attach the wrist strap to any piece of equipment with an electrical current present.
Dual in-line memory module (or DIMM) is compact circuit board with sur- face-mount memory chips. The printer, which has two memory slots, has a 256 MB memory module already installed in one of the slots. By using both slots, the memory can be expanded to a maximum of 1024 MB (512 MB + 512 MB).
Page 219
Declare the additional RAM in the Windows printer driver (Properties/Con- figure tab). Print a configuration page ( that the total amount of the RAM installed in your printer is listed. Dual In-Line Memory Module (DIMM) PRINT/CONFIGURATION PG ) and verify...
Installing a Hard Disk Note It’s very important to protect the printer controller board and any associated circuit boards from electrostatic damage. Before performing this procedure, review the antistatic caution on page 203. In addition, always handle circuit boards by the edges only.
Page 221
Attach the left-side cover and tighten the screws. Reconnect all interface cables. Reconnect the power cord, and turn on the printer. Declare the hard disk in the Windows printer driver (Properties/Configure tab). Hard Disk...
Installing the CompactFlash card Note If the installed CompactFlash card was used with a device other than this printer, such as a computer or digital camera, the card is automatically formatted and all of its data is deleted. Note It is very important to protect the printer controller board and any associated circuit boards from electrostatic damage.
Page 223
Using a coin, remove the screw, and then lift up the left-side cover to remove it. Fully insert the CompactFlash card into the appropriate slot. When the CompactFlash card is correctly inserted, the button on the right side of the slot (circled in the illustration) slightly pops out.
Page 224
Reconnect the power cord, and turn on the printer. Declare the CompactFlash card in the Windows printer driver (Properties/ Configure tab). CompactFlash...
Duplex (2-sided) printing can be performed automatically with the duplex option and enough memory installed. See “Duplexing” on page 120. Kit Contents 1—Duplex option 2—Connector cover Installing the Duplex Option Turn off the printer. Remove the two covers on the right side. Duplex Option...
Page 226
Pull the lever, and then open the right side cover. ! " Before opening the right side cover, open Tray 1. Inside the right-side cover, press the tab on the cover shown in the illustration, and then remove the cover. Close the right side cover.
Page 227
Insert the two tabs on the duplex option into the mounting holes in the printer to install the duplex option. ! " Support the duplex option with your hands until it is securely mounted onto the machine.
Page 228
While pressing on the inside the cover of the duplex option, secure the duplex option with the two screws. ! " Use a coin to install the screws. Close the duplex cover. Insert the connector on the duplex option into the connector on the machine.
Page 229
Attach the connector cover to the machine. Duplex Option...
Note When setting up the printer and lower feeder unit at the same time, attach the lower feeder unit before setting up the printer. If consumables are first loaded into the printer, it may become heavy, making it difficult to perform the procedure.
Page 231
Turn off the printer and discon- nect the power cord and inter- face cables. Remove the lower-right cover of the printer, as shown in the illus- tration. Remove the cover by inserting your finger into the hole at the front of the cover, then pulling off the cover as shown.
Page 232
Attach the upper cover to the sec- ond and subsequent lower feeder units. ! " If only one lower feeder unit was installed, do not install the upper cover. If multiple lower feeder units are to be installed, stack them together.
Page 233
If two or three lower feeder units are to be installed, stack the lower feeder units and secure them together before installing them to the printer. ! " When placing the printer on the optional tray unit, align the front and back of the printer and the unit. Lower Feeder Unit 59 kg...
Page 234
WARNING! Lifting the printer in an awkward position or transporting it in a poorly balanced position could result in personal injuly. When transporting the printer, assign an adequate number of persons to the job and ensure that each person can take a good position of not being excessively loaded.
Page 235
Install the two securing brackets at the front of the printer. Close the trays. Lower Feeder Unit...
Page 236
Remove the mounting tape on the relay harness of the lower feeder unit, and then remove the cover over the relay harness connection slot on the printer. If multiple lower feeder units have been installed, remove the cover over the relay harness...
Page 237
Connect the relay harness to the slot. If multiple lower feeder units have been installed, connect the relay harness of the bottom unit to the relay harness connection slot of the lower feeder unit, and then install the cover at its origi- nal position.
Page 238
Declare Tray 3/4/5 in the Windows printer driver (Properties/Configure tab). Lower Feeder Unit...
Caster Base By installing the caster base, the printer can more easily be set up at different locations. Note When using the caster base, attach the bottom lower feeder unit to the caster base before attaching the lower feeder unit to the printer.
Use the screws to attach the three ground fittings to the caster base. Screw the two adjusters onto the caster base. Use the screws to attach the three fixed legs to the caster base. Caster Base...
Page 241
Place the bottom optional lower feeder unit that is to be installed on the caster base. ! " For correct positioning, align the two M marks, which can be seen inside the hole in the lower feeder unit. Use the screws and linking plates to secure the lower feeder unit to the caster base.
Page 242
Be sure that the caster base is secured at all times except when the printer is being moved to a different location. ! " For details on attaching lower feeder units to the printer, See “Install- ing a Lower Feeder Unit” on page 216. Caster Base...
If the banner tray is installed, banner paper up to 1200 mm long can be loaded. Installing the Banner Tray Open Tray 1 (Manual Feed Tray). ! " Do not pull out the tray extension. If the tray extension is already pulled out, push it in.
Page 244
Make sure that the media guides are firmly pushed against the left and right sides of the banner paper. Begin printing. ! " Specify the same paper size as that specified with the custom size settings in the printer driver. Banner Tray...
Page 245
! " Remove each sheet of banner paper after it is fed out, otherwise the banner paper that is fed out may fall from the printer or cause a media misfeed in the printer. ! " After printing on banner paper, be sure to remove the banner tray and store it in a safe place.
EN 61000-3-3 China model GB 9254 class B, GB 17625.1 Australian model EN 55022 class B Desktop full color tandem laser beam printer Semiconductor laser beam scanning + Dry electron photography method 4 laser diode and polygon mirror Two-component HMT...
Page 249
First print Print speed Warm-up time Media sizes Technical Specifications Simplex Monochrome/Full color: 8.1/11.4 seconds for A4 (plain paper) Monochrome/Full color: 8.2/11.4 seconds for Letter (plain paper) Duplex Monochrome/Full color: 15.8/19.1 seconds for A4 (plain paper) Monochrome/Full color: 15.9/19.2 seconds for Letter (plain paper) Simplex Monochrome/Full color:...
Page 250
Paper/Media Input capacity Output capacity Operating temperature Operating humidity Power supply Power consumption Amperage Acoustic Noise External dimensions • Plain paper (64 to 90 g/m • Recycled paper (64 to 90 g/m bond) • Transparency • Transparency2 • Envelopes • Thick Stock 1 (91 to 150 g/m •...
Page 251
Weight Interface Standard memory Backup battery Technical Specifications Printer: approximately 50.5 kg (111.3 lb) Toner cartridge: Standard in-box cartridge = 0.3 kg (0.7 lb) (Y, M, C)/ 0.4 kg (0.9 lb) (K) Replacement cartridge (High-Capacity) = 0.5 kg (1.1 lb) (Y, M, C)/ 0.7 kg (1.6 lb) (K)
! " The values listed in the below tables indicate the number of pages for simplex printing using A4/Letter-size media with 5% coverage. The actual life may differ (be shorter) depending on the printing condi- tions (coverage, paper size, etc.), differences in the printing method, such as continuous printing or intermittent printing (when print jobs of one page are often printed), or the type of paper used, for example, thick paper.
Our Concern for Environmental Protection ® As an ENERGY STAR Partner, we have determined that this machine meets the ENERGY STAR Guidelines for energy efficiency. What is an ENERGY STAR product? An ENERGY STAR product has a special feature that allows it to automati- cally switch to a “low-power mode”...
Page 255
Index Accessories 202 DIMMs 204 Duplex option 211 Hard disk 206 Lower feeder unit 216 Antistatic protection 203 Banner Tray 229 Camera Direct 84 Caster Base 225 Configuration menu 32 Consumables Backup battery 139 Imaging unit 132 Toner cartridge 126 Index Waste toner bottle 137 Control panel 28...