Download
Share
Print this page
Watts AERCO Eurotherm 3508 Technical Application Manual
  1. Manuals
  2. Brands
  3. Watts Manuals
  4. Controller
  5. AERCO Eurotherm 3508
  6. Technical application manual

Watts AERCO Eurotherm 3508 Technical Application Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Technical Application Guide
Eurotherm 3508 Controller
Disclaimer
The information contained in this manual is subject to change without notice
from AERCO International, Inc. AERCO makes no warranty of any kind with
respect to this material, including, but not limited to, implied warranties of
merchantability and fitness for a particular application. AERCO International is
not liable for errors appearing in this manual, not for incidental or
consequential damages occurring in connection with the furnishing,
performance, or use of these materials.
Heating and Hot Water Solutions
AERCO International, Inc. • 100 Oritani Drive • Blauvelt, NY 10913
USA: T: (845) 580-8000 • Toll Free: (800) 526-0288 • AERCO.com
Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST
© 2022 AERCO
TAG-0101 • DRAFT

Advertisement

loading

Related Manuals for Watts AERCO Eurotherm 3508

Summary of Contents for Watts AERCO Eurotherm 3508

  • Page 1 Technical Application Guide Eurotherm 3508 Controller Disclaimer The information contained in this manual is subject to change without notice from AERCO International, Inc. AERCO makes no warranty of any kind with respect to this material, including, but not limited to, implied warranties of merchantability and fitness for a particular application.

  • Page 2: Operator Buttons

    Eurotherm 3508 Controller Guide Section 1: OPERATOR BUTTONS 1 OPERATOR BUTTONS Auto/Manual Page Scroll Lower Raise A/MAN Toggles the selected loop between Auto and Manual operation. This button Manual operation means that the controller output power is adjusted by the user. The input can be sensor is still connected and reading the PV but the control loop is open.
  • Page 3 Eurotherm 3508 Controller Guide Section 2: NORMAL OPERATION HOME DISPLAY 2 NORMAL OPERATION HOME DISPLAY Units When the button is Process Variable (PV1) pressed the Setpoint source is shown, e.g. SP1 Setpoint (SP1) Output/Valve Position & Bar Graph Indicator, e.g. TAG-0101 •...

  • Page 4: Beacon Display And Description

    Eurotherm 3508 Controller Guide Section 3: BEACON DISPLAY AND DESCRIPTION 3 BEACON DISPLAY AND DESCRIPTION In a single loop controller OP1 and OP2 operate channel 1 and 2 outputs respectively for the configured loop. Illuminates when manual mode active. If the HOME display is showing the dual loop overview, MAN illuminates if Loop 1 is in manual.
  • Page 5 Eurotherm 3508 Controller Guide Section 4: SELECTING AUTO/MANUAL OPERATION 4 SELECTING AUTO/MANUAL OPERATION TAG-0101 • DRAFT Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 5 of 10...

  • Page 6: Access Levels

    Eurotherm 3508 Controller Guide Section 5: ACCESS LEVELS 5 ACCESS LEVELS Parameters are available under different levels of security are Eurotherm 3508 Access Levels Level 1, Level 2, Level 3 and Configuration Level. Level Pass Code Level 1 has no security password since it contains a minimal Level 1 Default set of parameters generally sufficient to run the process on a...
  • Page 7 Eurotherm 3508 Controller Guide Section 6: SELECTING ACCESS LEVELS 6 SELECTING ACCESS LEVELS () 1. From any display press and hold the PAGE button. After a few seconds the display will enter the Access List & show: Goto Level 1. () NOTE: Press SCROLL button to scroll through the list of Access parameters.
  • Page 8 Eurotherm 3508 Controller Guide Section 7: FUNCTION BLOCK NAVIGATION DIAGRAM 7 FUNCTION BLOCK NAVIGATION DIAGRAM TAG-0101 • DRAFT Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 8 of 10...
  • Page 9 Eurotherm 3508 Controller Guide Section 8: CHANGING MODBUS ADDRESS 8 CHANGING MODBUS ADDRESS  1. From Access Level 3 press until the Digital Communications Function Block is displayed. ▲ ▼ until Comms Identity “H” is displayed. 2. Press  3. Press until the Address Parameter is displayed.
  • Page 10 Eurotherm 3508 Controller Guide Section 9: TRANSITION FROM LOCAL TO REMOTE SETPOINT CONTROL 9 TRANSITION FROM LOCAL TO REMOTE SETPOINT CONTROL  1. Press until the Control Loop 1 (Lp1) Function Block is displayed. ▲ ▼ 2. Press until Setpoint (SP) is displayed. ...