Download
Share
Print this page
Toro TX 1000 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Tools
  5. TX 1000
  6. Installation instructions manual

Toro TX 1000 Installation Instructions Manual

Wide track compact tool carrier
Hide thumbs Also See for TX 1000:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Wear Block Kit
TX 1000 Wide Track Compact Tool Carrier
Model No. 136-5821
This product contains a chemical or chemicals known to the State of California
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Read the Operator's
Manual.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
to cause cancer, birth defects, or reproductive harm.
136-5750
2. Tension block guide
Register at www.Toro.com.
WARNING
CALIFORNIA
Installation
1
Preparing the Machine
No Parts Required
Procedure
1. Park the machine on a level surface.
2. Remove any attachments from the machine.
3. Engage the parking brake.
4. Lower the loader arms so that they are
approximately 20 to 25 cm (8 to 10 inches)
above the frame.
5. Shut off the engine and remove the key.
6. Raise the machine off the ground until you
can access the inside of the track beneath
the machine. Support the machine using jack
decal136-5750
stands.
Note:
Refer to the Operator's Manual for your machine
to determine the weight.
WARNING
Mechanical or hydraulic jacks may fail to
support the machine and cause serious
injury.
Use jack stands when supporting the
machine.
Form No. 3414-689 Rev A
Installation Instructions
Use jack stands rated for your machine.
Original Instructions (EN)
All Rights Reserved *3414-689* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro TX 1000

Summary of Contents for Toro TX 1000

  • Page 1 Form No. 3414-689 Rev A Wear Block Kit TX 1000 Wide Track Compact Tool Carrier Model No. 136-5821 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
  • Page 2 Installing the Tensioning Removing the Tracks Decal No Parts Required Parts needed for this procedure: Procedure Decal Note: Complete the procedure for both tracks. 1. Remove the locking bolt and nut (Figure Procedure Install the tensioning decal on a clean, dry surface on the tension tube as shown in Figure 1 on both sides...
  • Page 3 4. Remove the outer front wheel (Figure Installing the Track Guides Parts needed for this procedure: Template Track Guide Button-head bolt Hex-socket-head bolt Thread-locking compound g217640 Figure 4 1. Nut 3. Outer front wheel Procedure 2. Washer (2) 4. Track Note: Complete the procedure for both track frames.
  • Page 4 g217544 Figure 9 g215024 Figure 7 1. Inner guide rod 1. Nut 3. Hex-socket-head bolt in front hole 2. Templates 4. Mark these holes. 4. Mark the locations of the other 2 holes using a 1/4-inch center drill bit (Figure Installing the Track Note: You may use a 1/4-inch drill bit if you do...

  • Page 5: Adjusting The Track Tension

    9. Align the closest notch in the tension screw to the locking-bolt hole and secure the screw with the locking bolt and nut (Figure Adjusting the Track Tension For Existing Tracks 1. Remove the locking bolt and nut (Figure No Parts Required 2.
  • Page 6 Notes:...
  • Page 7 Notes:...

This manual is also suitable for:

136-5821