1. Manuals
  2. Brands
  3. Toro Manuals
  4. Tools
  5. 41569
  6. Installation instructions manual

Toro 41569 Installation Instructions Manual

Kit, multi-pro 5600 sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Hose Reel Kit
Multi-Pro 5600 Sprayer
Model No. 41569
Installation
Note: Determine the left and right sides of the machine from the normal operating position.
Note: For an electrical schematic and flow diagram, refer to the Parts Catalog.
Note: You will need to purchase Teflon tape before installing this kit.
Description
Hose reel support
Flange-head bolt, 3/8 x 1 inch
Flange nut, 3/8 inch
Hose reel strap
Hose reel assembly
Flange nut, 5/16 inch
Flange-head bolt, 1/2 x 1/2 inch
Flange nut, 1/2 inch
Plastic hose clamp, large (1 inch)
Plastic hose clamp, small (1/2 inch)
Control box mounting bracket
Flange-head bolt, 5/16 x 3/4 inch
Flange nut, 5/16 inch
Ball valve assembly
Flange-head bolt, 1/4 x 3/4 inch
Flange nut, 1/4 inch
Short hose, 1/2 inch dia
Plastic barbed fitting, 1/2 inch
2002 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Qty.
Use
1
10
10
2
Assemble the frame.
1
1
1
1
1
1
1
2
4
6
1
Install the flow control box.
2
2
1
4
2
1
3
1
1
Form No. 3328-916
Installation Instructions
All Rights Reserved
Printed in the USA

Advertisement

Table of Contents
loading

Related Manuals for Toro 41569

Summary of Contents for Toro 41569

  • Page 1: Table Of Contents

    Flange-head bolt, 1/4 x 3/4 inch Flange nut, 1/4 inch Rubber trim piece Short hose, 1/2 inch dia Plastic barbed fitting, 1/2 inch 2002 by The Toro Company All Rights Reserved Printed in the USA 8111 Lyndale Avenue South Bloomington, MN 55420-1196...
  • Page 2 Description Qty. Pressure gauge Reducer fitting and nut Plastic fitting, small Control box cover Silver fitting, small Red tubing Toggle switch Install the switches, gauge, and cover Momentary switch Rear control box wire harness Fuse, 10 amp Switch wire cover Flange-head bolt, 1/4 x 3/4 inch Flange nut, 1/4 inch Knob...

  • Page 3: Flange-Head Bolt, 5/16 X 1 Inch

    Assembling the Frame 1. Install the hose reel support to the hydraulic reservoir mount (Fig. 2) using 2 flange-head bolts (3/8 x 1 inch) and 2 flange nuts (3/8 inch). Do not fully tighten the nuts to allow for adjustment later. m-6350 Figure 3 1.

  • Page 4: Control Box Support Bracket

    Note: Check the position of the right boom holder. It should be installed as far down in the mounting slots as possible. If it is not, loosen the mounting fasteners, slide it down, and tighten the fasteners. m–6398 3-5/8 inches (9.2 cm) Figure 5 1.

  • Page 5: Control Valve Assembly

    Tapping into the Machine Hoses 1. Remove the retainer securing the end of the boom supply hose connected to the tee located to the right of the boom supply valves and disconnect it (Fig. 9). 8 inches (20 cm) m–6375 Figure 10 1.

  • Page 6: S53 Tee Fitting

    9. Cut the by-pass hose half way between the boom valves and the tank (Fig. 12). m–6355 Figure 13 1. Control box mounting 3. Flange nut, 5/16 inch bracket 2. Flange-head bolt, 5/16 x 3/4 inch 2. Connect the end of the lever assembly on the small ball valve assembly to the control valve assembly (Fig.

  • Page 7: Rubber Trim Piece

    3. Connect the fitting you installed into the boom supply hose to the control valve assembly, securing it with the retainer you removed previously (Fig. 15). m–6384 Figure 16 1. Right side of the control 2. From agitation hose box mounting bracket 3.

  • Page 8: Pressure Gauge

    19. Connect a 1/2 inch hose to the open fitting on the 2. Install the black plastic fitting into the reducer fitting on control valve assembly (Fig. 18). the gauge (Fig. 19). 3. Install the pressure gauge into the bracket under the circular opening inside the control box cover, securing it with the nut packaged with it (Fig.
  • Page 9 6. Disconnect the connectors under the dash between the 7. Connect the T-end of the new rear control box harness manual control box and the spray harness (Fig. 21). between the manual control box harness and the spray harness (Fig. 21 and 22). 8.

  • Page 10: Switch Wire Cover

    10. Connect the middle lead with the spade connector to the 15. Install the switch wire cover over the switches and open lead on the fuse box under the driver’s seat around the wires (Fig. 27) and secure it with (Fig.

  • Page 11: Spray Gun

    Connecting the Spray Hose Caution 1. Wrap Teflon tape counterclockwise around the threads of the hose fitting on the long hose and install the fitting Hands, loose clothing, long hair, and jewelry could into the connecting tube on the reel (Fig. 29). get caught in the hose and reel while rewinding and cause injury.
  • Page 12 Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-1277 95-2213 1. Boom spray 2. Hand spray 87-0540 106-1278 1.

  • Page 13: Figure

    Operation Warning Fluid under pressure can penetrate skin and cause injury. Keep your body and hands away from nozzles that eject high pressure fluid. Do not aim the sprayer at any person or animal. Make sure all fluid hoses and lines are in good condition and all connections and fittings are tight before applying pressure to the system.
  • Page 14 Caution Hands, loose clothing, long hair, and jewelry could get caught in the hose and reel while rewinding and cause injury. Keep your hands clear of the reel and hose while it is rewinding. Do not wear loose clothing or jewelry and tie up long hair.

Table of Contents