2) F20 must use a power socket with reliable protective grounding; 3) F20 is heavy and should be placed on a firm and stable work surface to prevent accident ; 4) F20 should be kept away from children, and never allow...
5) No objects can be placed on the top of F20, and no liquids are allowed to enter the interior; 6) F20 works at a high temperature, so it needs good ventilation. Do not use it in a humid environment to avoid abnormal accidents;...
2.2 Hazardous areas The hazardous area of the F20 sintering furnace is shown in the table below: Dangerous area Hazard type Sides of furnace Burn hazard Lifting areas Crush hazard Furnace internal parts Electric shock hazard Operation and configuration 3.1.1 Operating Instructions Power Switch, switch to I to turn on the machine and start using.
3.1.2 Control Panel The F20 furnace is equipped with a large colorful touch screen, all operations can be easily controlled via it. The main user interface is divided into two parts: 1 . O p e rat i o n a rea ( i n c l u d i n g l i f t co n t ro l b u tto n , s i n te r i n g co n t ro l...
Page 8
Time display box: display the remaining sintering time in real time during sintering. Fault display box: 1) Click this box, the fault code table will pop up. 2) When the F20 sintering Settings box: Click this box to change password settings...
2) Fault display box: Click on the fault display box, and a fault code table will pop up. When the fault code pops up during the use of the F20 sintering furnace, fault cause can be found out from this fault code table, and the fault can be solved according...
Page 10
3) Setting box: Click the setting box to pop up the circuit calibration and setting password box. The circuit calibration module is only open to the technical support of UP3D TECH. A password is set for the customer to manage the defined sintering program, preventing others from tampering with the defined program.
Page 11
On the password input interface, click the Enter password box, and the numeric keyboard box will pop up. Put in factory password 66666 in keyboard, click OK to enter the password setting interface; On the password setting interface, click the Enter password box, and the numeric keyboard box will pop up.
Page 12
After re-entering the same new password, click OK to complete the password change. Note that you must remember the 6-digit new password after change. If you forget it, you can only restore it and reset it, which will ca use the loss of the customized sintering program.
Page 13
Click the specific program or the serial number on display box to enter the program parameter interface. Click the program confirmation box, it means that the program is selected, and it will automatically return to the main interface. When you need to customize and edit the sintering program, you need to click the modify parameter box, and then enter the password input interface.
Page 14
Click the Enter password box, and the numeric keyboard box will pop up. Put in the correct 6-digit password, if incorrect, a reminder box will pop up at the bottom of the password box.
Page 15
If the 6-digit password is correct, you can enter the program parameter interface where parameters can be edited. Click the program name box, an alphabetic keyboard box will pop up, click the CAPSLOCK box to switch between Chinese and English input, switch to Chinese to input Pinyin, and click the left and right switching buttons to turn pages.
Page 16
T h e w h i te b oxe s i n t h e pa ra m ete r s ett i n g a rea s o f h eat i n g , temperature, and temp. preser vation in the program parameter interface represent different definitions, and the range of parameter values that can be input i s a l s o di f fere n t .
Page 17
T h e d e f i n i t i o n o f e a c h b o x a n d t h e v a l u e r a n g e o f i n p u t parameter are shown in the following table: The first stage heating rate , valid value range: 5-20℃...
3.2 Configuration Instructions 1. Function configuration of F20 smart sintering furnace: Sintering program: 20 programs can be freely set by the user Easy to search when sintering. Number of Three layers of sintering tray can be placed at the same time,...
Page 19
2. Basic factor y configuration of sintering cur ve: (for reference only) Program code description Program code Description UPCERA ST single crown UPCERA ST short bridge UPCERA ST long bridge Xiangtong, less than 5 units Xiangtong, more than 5 units UPCERA color zirconia sngle crown UPCERA color zirconia short bridge UPCERA color zirconia long bridge...
UP3D TECH for solutions; Note: It is recommended to keep the package for future transportation; 4.2 Assembly Step 1: Place the main body of the F20 sintering furnace on the workbench surface specified in 1.2 Operation Precautions; Step 2: Insert the power cord into the main body of the sintering...