Corsair Hydro H150i PRO Quick Start Guide

Note: Most newer PC cases include a CPU cutout to allow access to the bottom of the motherboard. If your case does not include a cutout, you will need to remove your motherboard from the case before installation.

INTEL

Included Hardware

Highlighted parts for Intel installation only

1. x24 LONG FAN SCREWS
   
2. x4 LGA 115X / 1366 STANDOFF
   
3. x4 LGA 2011/2011-3/2066 STANDOFF
   
4. x2 AMD SCREW CLIP
   
5. x4 THUMBSCREWS
   
6. x12 RADIATOR SCREWS
   
7. x1 CORSAIR LINK USB CABLE (Included)
   
8. x3 ML120 PWM FANS
   
9. x24 WASHER
   
10. x1 INTEL BACKPLATE
    
11. x1 INTEL MOUNTING BRACKET (PRE-INSTALLED)
    
12. x1 AMD MOUNTING BRACKET
    

Note: The H150i PRO comes with Intel mounting bracket pre-installed on the pump for quick installation.

Installing the Intel Backplate

• For LGA 115X installation, slide the backplate pins inside (figure 1).
• For LGA 1366 installation, slide the backplate pins outside (figure 1).
  
  Figure 1
• Install the assembled backplate (figure 2).
  
  Figure 2
  Note: Intel LGA 2011 and LGA 2066 does not require backplate installation. Proceed to step 2.

Installing the Intel Standoff Screws

• Attach the provided Intel standoff.
• Use (B) for LGA 115X / 1366, or (C) for LGA 2011 / 2011-3 / 2066.
• Tighten all four screws until firmly secure.
  

Install the Fans and Radiator

Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.

Installing the Pump Unit

• Align the bracket and pump over the standoff screws as shown.
• Tighten the thumbs screws until all four corners are firmly secured.
  

Connect Power to the Fans and Pump

• Connect pump power cable to an available SATA power plug (figure 1).
  
  Figure 1
• Connect pump tach cable to the CPU_FAN header on your motherboard (figure 1).
• Connect each fan to the shrouded 4 pin connectors on the pump (figure 2).
  
  Figure 2

Connect Pump to USB Header

Using the included CORSAIR LINK USB cable, attach pump unit to a motherboard USB header.

AMD

Included Hardware

Highlighted parts for AMD installation only

1. x24 LONG FAN SCREWS
   
2. x4 LGA 115X / 1366 STANDOFF
   
3. x4 LGA 2011/2011-3/2066 STANDOFF
   
4. x2 AMD SCREW CLIP
   
5. x4 THUMBSCREWS
   
6. x12 RADIATOR SCREWS
   
7. x1 CORSAIR LINK USB CABLE (Included)
   
8. x3 ML120 PWM FANS
   
9. x24 WASHER
   
10. x1 INTEL BACKPLATE
    
11. x1 INTEL MOUNTING BRACKET (PRE-INSTALLED)
    
12. x1 AMD MOUNTING BRACKET
    

Installing the AMD Mounting Bracket

Note: It is important that the AMD retention bracket be evenly secured on all sides before installation!

• Remove the integrated Intel mounting bracket by turning the mounting bracket, and pulling away from the copper coldplate (figure 1).
  
  Figure 1
• Install the AMD bracket by aligning the twist lock, pushing in, turning the opposite direction, and allowing bracket to secure (figure 2).
  
  Figure 2

Install the Fans and Radiator

Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.

Prepare the Mounting Bracket

Insert the AMD screw clips and secure with the screws as shown. Do not tighten the thumb screws all the way.

Install the Pump Unit

Align the bracket with the Stock AMD mounting clips as shown. Tighten the thumb screws until secure.

Connect Power to the Fans and Pump

• Connect pump power cable to an available SATA power plug (figure 1).
  
  Figure 1
• Connect pump tach cable to the CPU_FAN header on your motherboard (figure 1).
• Connect each fan to the shrouded 4 pin connectors on the pump (figure 2).
  
  Figure 2

Connect Pump to USB Header

Using the included CORSAIR LINK USB cable, attach pump unit to a motherboard USB header.

FAQ

1. How do I know the direction of the air flow of the fan?
   An arrow located on the side of the fan indicates the direction of air flow.
2. Can I reuse the pre-applied thermal paste on the H150i PRO for a re-installation?
   Re-installation of the H150i PRO cooler will require you clean off the pre-applied thermal paste and apply an aftermarket paste.
3. Where can I purchase additional Radiator screws for push/pull Configuration?
   Additional screws can be purchased from www.corsair.com

Please visit: corsair.com to download a detailed user guide or to obtain technical support.

EMAIL: support@corsair.com
FACEBOOK: facebook.com/corsairmemory
BLOG: corsair.com/blog/
FORUM: forum.corsair.com
TWITTER: twitter.com/corsair
USA and CANADA: (510) 657-8747 | INTERNATIONAL: (888) 222-4346 | FAX: (510) 657-8748
47100 Bayside Parkway • Fremont • California • 94538 • USA

© 2017 CORSAIR Components, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks, and CORSAIR is a trademark in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.

Documents / Resources

References

• PC Components | Gaming Gear | CORSAIR
• http://corsair.com
• http://facebook.com/corsairmemory
• http://corsair.com/blog/
• Home - Corsair Community
• http://twitter.com/corsair

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Corsair Hydro H150i PRO Quick Start Guide