Download Print this page

Jenn-Air JGD8130AD User Manual page 7

Gas downdraft cooktop
Hide thumbs Also See for JGD8130AD:

Advertisement

Available languages

Available languages

S
B
EALED
URNER
C
(
)
ARTRIDGE
S
TO INSTALL SEALED BURNER
CARTRIDGE:
1. Be sure control knobs are turned OFF.
2. Clean
basin
of
any
accumulation. (See page 9 for cleaning
recommendations.)
3. With the back raised, position the burner
cartridge with the mixer tube openings
and ignitor rods toward the orifices
and terminal receptacle. Slide the
cartridge until the tubes and ignitors
start to engage, then lower the cartridge
so that it rests on the cooktop surface.
Gently slide forward to fully engage.
TO REMOVE SEALED BURNER
CARTRIDGE:
1. Control knobs should be in the OFF
position and the cooktop should be
cool.
2. Lift up the edge of the cartridge until
the bottom of the cartridge clears the
basin. (Lifting the cartridge too high
while still engaged could damage the
ignitor rods and mixer tubes.)
3. To disengage the cartridge, hold by the
sides and pull away from the terminal
receptacle and orifices. Lift out when
fully unplugged.
4. Do not stack cartridges where they
may fall or be damaged.
NOTE: Optional Sealed Burner
Cartridge, model JGA8100, can replace
the grill burner assembly.
G
I
RILL
NSTALLATION
The grill assembly consists of two grill
grates and a grill burner. Only install the
grill on the LEFT SIDE of your cooktop.
TO INSTALL GRILL:
grease
1. Before installing grill components, be
sure controls knobs are in the OFF
position.
2. Position the grill burner with mixer
tubes and ignitor rod toward the orifices
and terminal receptacle. Slide the
burner until the tubes and ignitor
engage, then lower the burner until it
rests on the mounting pins.
3. Place the grill grates on top of the
cooktop.
NOTE: Before using the grill for the
first time, heat the grill burner to remove
the protective shipping coating. Heat
the grill burner on Hi for 10 minutes
and use the vent system to remove any
additional smoke during cooling.
TO REMOVE GRILL:
1. Be sure control knobs are in the OFF
position and the grill components are
cool.
2. Remove grill grates.
3. Lift the burner up slightly. Slide the
burner away from the orifices and
terminal receptacle.
U
• Before the first use, wash grill grates in
• Preheat the grill on Hi for 5 minutes.
• Use nonmetallic spatulas or utensils to
• Excessive amounts of fat should be
• Allowing excessive amounts of grease
• Excessive flare-ups indicate that either
• Grease drippings will occasionally
• NEVER LEAVE GRILL UNATTENDED
6
G
SING THE
RILL
hot soapy water, rinse and dry. Then
"season" the surface by wiping on a
thin coating of cooking oil. Remove
excess oil by wiping with paper towel.
This procedure should be repeated
when either:
a) cleaning in the
dishwasher since the detergent may
remove seasoning or b) anytime a
sugar-based marinade (for example,
barbecue sauce) is going to be used.
Preheating improves the flavor and
appearance of meats and quickly sears
the meat to help retain the juices.
prevent damaging the nonstick grill grate
finish.
trimmed from meats. Only a normal
amount is necessary to produce the
smoke needed for that smoked,
"outdoor" flavor. Excessive fat can
create cleaning and flare-up problems.
or drippings to constantly flare-up voids
the warranty on the grill grates.
the grill interior needs to be cleaned or
that excessive amounts of fat are in the
meat or the meat was not properly
trimmed.
ignite to produce harmless puffs of
flame for a second or two. This is a
normal part of the cooking process.
DURING GRILL OPERATION.
Cont.

Hide quick links:

Advertisement

loading

This manual is also suitable for:

Jgd8130adwJgd8345adJgd8130adsJgd8345adbJgd8130Jgd8345