Advertisement
Table of Contents
CONVERTIBLE GAS GRILL
COOKTOP SERIES
JGD8130 & JGD8345
JENN-AIR
DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS
*Blower may be rotated for horizontal or verticaldirection by looseningnuts aroundblower inlet. Accessible insideventilation
chamber.
• NOTICE TO INSTALLER: Leave these instructions with the appliance.
• NOTICE TO CONSUMER: Retain these instructions for future reference.
REGULATOR
TIE DOWNBOLT
ON EACHEND
BOXCOVER
GREASE
BLOWER CANBE
CONTAINER
SWIVELED 90°
29" _1/
21" + 1116"
7 Q/16"
Min.
Cbarar_e
2.38cm
SELECTAPPROPRIATE
DUCTCUTOUT(SEE
DUCTINGINSTALLA-
TIONINSTRUCTIONS).
_EAS[
CONTA t NER
2 7/8 °_
_13
3/4"--,.*_.|t
13/115-_..
7.3
Cm
34.9
cm
30.0
cm
TtE DOWNBOLT
ONEACHEND
GREASE
BLOWER CANBE
CONTAINER
SWIVELED 90'=
APPUANCE PRF.SSURE
REGULATOR
SELECT APPROPRIATE
DUCTCUTOUT
DUCTING INSTALLA-
TIONINSTRUCTIONS).
43 114" +lt
21" _- 1/16"
79/16"
19.21cm
1 7_"
Min.
4.76cm
COH_AI_
INSTRUCTIONS TO INSTALLER
• Dimension "A"- Provide 2" rain. (5.08 cm) cabinet clearance to motor for cooling purpose,
• Note - Where possible, 6" (15.24 cm) is recommended for motor/blower service.
• Side Clearance - Grills installednear a side wall must allow a minimum clearance of 8".
• Access must be providedto remove and empty grease container(s),
8101P406-60
(o9-ol-oO)
/
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jenn-Air JGC9536ADB - 36" Gas Cooktop
Summary of Contents for Jenn-Air JGC9536ADB - 36" Gas Cooktop
- Page 1 CONVERTIBLE GAS GRILL COOKTOP SERIES JENN-AIR JGD8130 & JGD8345 DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS *Blower may be rotated for horizontal or verticaldirection by looseningnuts aroundblower inlet. Accessible insideventilation chamber. • NOTICE TO INSTALLER: Leave these instructions with the appliance. •...
- Page 2 Installing Cabinetry Over Your Jenn-Air Grill *A = 30" (76.2 cm) minimum verticat clearance between of local codes, with the latest edition of the National Electrical Code ANSI/NFPA No. 70 USA or current CSA cooking surface and construction above the appliance. STANDARD C22.1 Canadian Electrical Code part 1.
-
Page 3: Instructions To Installer
Instructions To Installer Nr Shutter Adjustment 1. Chamfer all exposed edges of decorative laminate to This appliance is shipped from the factory with air shutters prevent damage from chipping. adjusted for use with N=ural Gas. If further adjustment is necessary, or to reset for use with LP, adjust air shutters as 2, Radius corners of cutout and file to insure smooth follows: edges and prevent corner cracking. -
Page 4: Pressure Testing
PressureTesting Low Flame Adjustment (SeeIllustration " C") This appliance is shipped from the factory with low and The maximum gas supply pressure for the appliance mediumflame settingsadjusted for use with Natural Gas. If pressure regulator supplied on this appliance is 14" W.C. further adjustment is necessary, or to readjust for use with The test pressure for checking this appliance pressure LP, proceed as follows:... -
Page 5: Conversion To Lp Gas
Conversion To LP Gas This appliance is shippedfrom the factory equipped for use with Natural Gas. To convert it from Natural Gas for use with I_OPEN LP Gas, perform steps 1 through 4. WRENCH 1. Remove natural gas orifice hoods. Install color coded orifice hoods supplied, located in a pack attached to the outer plenum area of this appliance. - Page 6 TO CONVERTAPPLIANCEFOR USE WITH PROPANEGAS Natural Gas To Propane Gas (LP) Conversion Instructions ...,, F.LECTmCAL e, S .UST Authorized Service Contractor (or TURNEDOFF PRIOR.TOC0¢__:' other qualifiedagency) in accordancewith the _man_s:!nstructlons anda, codesand ='_uL_'n_, ,of _the , authority having ® u_o_ Failure to follow instructions could .,_ult_ serious "injury or property damage.
- Page 7 TO CONVERTAPPLIANCEFOR USE WITH NATURALGAS Models - JGD8130 & JGD8345 Series Propane Gas (LP) To Natural Gas Conversion Instructions Manifold - Natural Gas pressure required - 5" W.C. If this appliance has been converted for use with LP Gas, Incoming Natural Gas pressure required to appliance each of the following modifications must be performed to pressure regulator - 6"...
- Page 8 REQUIREDADJUSTMENTS AT TIME OF INSTALLATION The installation of this appliance must conform with local codes, or in the absence of local codes, with the latest edition of the National Fuel Gas CodeANSI Z223.1 USA or current CAN/CGA-B149 Installation Code. -'-']This range was manufactured for use with Natural Gas.
Need help?
Do you have a question about the JGC9536ADB - 36" Gas Cooktop and is the answer not in the manual?
Questions and answers