Operating Adjustments; The Control Panel - Blizzard Lighting COLORSTORM 252 Manual

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the COLORStorm™
252 are accessed by using the control panel on the front of the fi xture.
There are 4 control buttons below the LED display which allow you to
navigate through the various control panel menus.
<MODE>
Is used to initially access the control panel system, and also navigate
to the previous higher-level menu item.
<SETUP>
Confi rms selections and navigates secondary control panel options.
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the fi rst available option for the selected
menu function. To select a menu item, press <ENTER>.
Press the <MODE> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <SETUP> button to select the menu function
currently displayed, or to enable a menu option. To return to the previ-
ous option or menu without changing the value, press the
<MODE> button.
COLORStorm 252 Manual Rev. B
Page 9
Copyright (c) 2010 Blizzard Lighting, LLC
To set the unit in DMX Mode
To control the COLORStorm 252 in DMX mode, fi rst select from one of the three
DMX control modes (3 Channel Mode 1, 3 Channel Mode 2, or 9 Chnanel Mode.)
1.) Press the <MODE> Button until the display reads
2.) To select 3 Channel Mode 1, press the <SETUP> Button, then use the
<UP> or <DOWN> Buttons until the display reads
3.) To select 3 Channel Mode 2, press the <SETUP> Button, then use the
<UP> or <DOWN> Buttons until the display reads
4.) To select 9 Channel Mode, press the <SETUP> Button, then use the <UP>
or <DOWN> Buttons until the display reads
To set the DMX address:
1.) Press the <MODE> button until the display reads
2.) Press the <SETUP> button until the display reads
3.) Use the <UP> and <DOWN> buttons to set the appropriate DMX address.
To run one of 13 built-in programs:
1.) Press the <MODE> Button until the display reads
For all programs except PG00, PG05, PG06:
1.) Use the <UP> or <DOWN> Buttons to select the appropriate program.
2.) Press the <SETUP> Button until the display reads
3.) Use the <UP> or <DOWN> Buttons to select the appropriate chase speed.
4.) Press the <SETUP> Button until the display reads
5.) Use the <UP> or <DOWN> Buttons to select the appropriate fl ash speed.
For PG00 (Static Color Selection):
1.) Press the <SETUP> Button until the display reads
2.) Use the <UP> or <DOWN> Buttons to select the appropriate static color.
For PG05 (Flash Color Selection):
1.) Press the <SETUP> Button until the display reads
2.) Use the <UP> or <DOWN> Buttons to select the appropriate fl ash color.
To step through all built-in programs:
1.) Press the <MODE> button until the display reads
To step through all built-in programs in Sound Active Mode:
1.) Press the <MODE> button until the display reads
2.) Use the <UP> or <DOWN> Buttons to adjust sound sensitivity between 1
and 31.
To set additional units as slaves while in Program/Sound Ac-
tive/Auto Mode:
1.) Press the <MODE> button until the display reads
COLORStorm 252 Manual Rev. B
Addr
.
03Ch
.
P3Ch
.
09Ch
.
Addr
.
d001
.
PG00 PG12
to .
SP99
.
FS.00.
C-.-1.
C-.-1.
AU70
.
SO.31
.
SLA-
Page 10
Copyright (c) 2010 Blizzard Lighting, LLC