Advertisement
r_ Preparing the remote control
When you use the remote
control
for the first time, pull out
the insulation
sheet.
If the range or effectiveness
of the remote
control
decreases,
replace
the battery.
To replace
the
battery
in the remote
control
Lithium coin battery__...__
(product
number: CR2025)
-'_-__
+/'_'_
Insert the battery
into the remote
control
by matching
the
polarities
(+ and -) correctly.
NOTES
• Store the batteryin
a place where children
cannot reach. If
a child accidentallyswallows
the battery, consult a doctor
immediately.
• To prevent the batteryfrom
overheating,
cracking,
or
starting
a fire:
Do not recharge, short, disassemble
or heat the battery,
or
dispose of it in a fire.
Do not leave the battery with other metallic
materials.
Wrap the battery
with tape and insulate
when throwing
a way or saving it.
Do not poke the battery with tweezers or similar
tools.
• Dispose of the batteryin
the proper
manner, according
to
federal, state, and local regulations.
CAUTION:
Danger
of explosion
if battery
is incorrectly
replaced.
Replace only with the same or equivalent
type.
For USA-California
Only
This product
contains
a CR Coin Cell Lithium
Battery
which
contains Perchlorate
material--special
handling
may apply.
See www.dtsc.ca.qov/hazardou
swaste/perchlorate
Connecting the FM antenna
i
FM antenna
(supplied)
Rear of the unit
Extend the FM antenna
when connecting
so that you can
obtain
the best reception.
NOTES
• Make sure the antenna
conductors
do not touch any other
terminals,
connecting
cords or the power cord. Also, keep
the antennas
away from metallic parts of the main unit,
connecting
cords, and the AC power cord. Otherwise,
it
could cause poor reception.
• Ifyou want to get a better reception,
disconnect
the supplied
FM antenna,
and connect to an outdoor
FM antenna
(not
supplied)
using a 75 _ wire with coaxial type connector
(IEC
or DIN45325).
Installing the unit
Install the unit on a flat and level surface
to ensure the best
sound quality.
• The sound may be affected
depending
on the location
in which
you install it. To avoid such issues, change
the
location
and orientation
of the unit.
• For cathode-ray
tube television
(CRT):
If you install the unit near the TV, color distortion
may
occur. To prevent
this, turn off the TV's main power
or unplug
it before
installing
the unit. Wait at least 30
minutes
before
turning
on the TV's main power
again.
If the TV is still affected,
move the unit further
away.
Installing
on the wall
You can install the unit on the wall.
(not supplied
A: Minimum
6- 7 mm
(1/4" - 5/16")
B: Maximum
8.5 mm (3/8")
C: Maximum
6 mm (1/4")
D: o 4 mm (screw diameter)
(Dia. 3/16")
E: Minimum
15mm(5/8")
CAUTION
• The unit weighs approximately
3.4 kg (7.4 Ibs). Sufficient
care must be taken when installing
it on the wall to prevent
any accidents
caused by its falling
off..
• Use screws, which are compatible
with the strength
and
material
of the pillar or wall to prevent the unit from falling
off.
• Do not install the unit onto a plywood
or plasterboard
wall;
otherwise,
it will fall and sustain damage.
• When installing
the uniton
the wall;
Be sure to have it installed on the wall by qualified
personnel
Care must be taken when selecting
a location
for
installation
on the wall. Injury to personnel
or damage
to
eq uipmen t may result if the installed
unit interferes with
daily activities.
AC adaptor
should not be hanging/placed
above any
other items. Place the AC adaptor
on the fiat floor only.
Recommended
mounting
surface: Wooden studs. If the
mount is to be installed
on any surface other than wooden
studs, use suitable
hardware
(which is commercially
available).
Connecting
the
TV remote
pass
through
cable
If you install the unit near the TV, the unit may block
the remote
control
signal of the TV, and it may not be
transmitted
to the TV unit. Connect
the TV remote
pass
through
cable (supplied)
to the unit for smooth
signal
transmission.
As illustrated
below,
connect
the TV remote
pass through
cable to the IR OUT terminal.
Move
the cable to the remote
sensor of your TV as closely as possible.
CAUTION
• Even if you connect the TV remote pass through
cable to the
unit, some TVs may not receive the remote control signal of
the TV. Because some TVs use different
carrier frequency
for
the remote control.
Rear of the unit
TV remote
pass
through
cable
(supplied)
\
Move it to the
', ofrem°teyou
rTvSens°r
/
i as closely as
' possible, then
/; stick it in any
the unit
• _,[_o_
is a trademark
of SRS Labs, Inc.
• StudioSound
HD technology
is incorporated
under
license from SRS Labs, Inc.
• SURROUND: StudioSound
HD by SRS Labs. SRS
StudioSound
HD
TM
provides
an immersive
and
engaging
surround
sound experience,
while
maintaining
steady volume
and delivering
rich bass
and clear dialog.
• DRC: TruVolume
by SRS Labs. TruVolume
TM
(designated
as DRC) maintains
a steady volume
for an enjoyable
viewing
experience.
Advertisement
