JVC TH-BC1 Instructions

ENGLISH
W
arnings, Cautions and Others /
CAUTION
The button in any position does not disconnect the mains line.
Disconnect the mains plug to shut the power off completely (the STANDBY
lamp goes off). The MAINS plug or an appliance coupler is used as the
HOME THEATER SOUND SYSTEM
disconnect device, the disconnect device shall remain readily operable.
• When the System is on standby, the STANDBY lamp lights red.
TH-BC1
• When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION
La touche , dans n'importe quelle position, ne déconnecte pas le
système du secteur. Déconnectez la fiche de secteur pour mettre l'appareil
complètement hors tension (le témoin STANDBY s'éteint). La fiche secteur
ou un coupleur est utilisé comme dispositif de déconnexion de l'appareil, et
l'appareil déconnecté doit être prêt à être utilisé.
• Quand le système est en attente, le témoin STANDBY est allumé en rouge.
Thank you for purchasing a JVC product. • Quand le système est sous tension, le témoin STANDBY s'éteint.
Before operation, please read the instructions carefully. L'alimentation peut être télécommandée.
For customer use:
CAUTION
Enter below the Model No. and Serial No. which are located either on the rear,
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
bottom or side of the cabinet. Retain this information for future reference.
ATTENTION
Model No.
Les piles ne doivent en aucun cas être exposées à une chaleur excessive
(lumière du soleil, feu, etc.).
Serial No.
CAUTION
INSTRUCTIONS
GVT0326-002A[J]
To reduce the risk of electrical shocks, fire, etc.:
1210WMKMDWJMM
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
EN
© 2010 Victor Company of Japan, Limited ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de
For U.S.A.
l'appareil.
2. Ne pas exposer l'appareil à la pluie ni à l'humidité.
This device compiles with RSS-210 of Industry Canada Rules. Operation
is subject to the following two conditions: (1) this device may not cause
The lightning flash with arrowhead symbol, within an
interference, and (2) this device must accept any interference, including
equilateral triangle, is intended to alert the user to the presence
interference that may cause undesired operation of the device.
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a
Cet appareil est conforme au réglement CNR-210 de l'industrie du Canada.
risk of electric shock to persons.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes:
The exclamation point within an equilateral triangle is intended
(1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit étre
to alert the user to the presence of important operating
prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est
and maintenance (servicing) instructions in the literature
susceptible de compromettre le fonctionnement du dispositif.
accompanying the appliance.
Pour les Etats-Unis For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO
NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-
CAUSING EQUIPMENT STANDARD ENTITLED "DIGITAL APPARATUS," ICES-003 OF
THE DEPARTMENT OF COMMUNICATIONS.
Pour le Canada
Le symbole de l'éclair à l'intérieur d'un triangle équilatéral est CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS
destiné à alerter l'utilisateur sur la présence d'une "tension RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE
dangereuse" non isolée dans le boîtier du produit. Cette tension B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR; "APPAREILS
est suffisante pour provoquer l'électrocution de personnes. NUMERIQUES", NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
Le point d'exclamation à l'intérieur d'un triangle
équilatéral est destiné à alerter l'utilisateur sur la présence
d'opérations d'entretien importantes au sujet desquelles des
renseignements se trouvent dans le manuel d'instructions.
I
ntroduction
Do not block the vents
Auto power save function
Blocking the vents may damage the System.
When no operation is done in certain situations for 29 minutes, the unit turns
Care of the cabinet
off automatically. This function is on at the initial setting. For details, refer to
• Stains on the System should be wiped off with a soft cloth. If the System is
"Operations."
heavily stained, wipe it with a cloth soaked in water diluted neutral detergent
and wrung well, then wipe clean with a dry cloth.
In this manual, the remote control buttons are used for explaining the
• Since the System may deteriorate in quality, become damaged or get its paint
operations unless mentioned otherwise. However, if the System has the same
peeled off, be careful about the following:
or similar button names, they can also be used for the operations.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinners, benzines or other organic solvents including
disinfectants.
Notes on handling
– DO NOT apply any volatile substances such as insecticides to it.
Important cautions – DO NOT allow any rubber or plastic to remain in contact with it for a long time.
• Do not place anything on top of the System. Doing so may cause the System to
Installation of the System
• Select a place which is level, dry, and neither too hot nor too cold; between fall, causing malfunctioning and/or injury.
•
5°C and 35°C (41°F and 95°F). The manufacturer accepts absolutely no liability for any accidents or damage
• resulting from inadequate assembly or mounting, insufficient strength of
Leave sufficient distance between the System and the TV.
attachment, misuse or abuse, or natural disasters.
• Do not use the System in a location near heat sources, or in a place subject to
If water gets inside the System
direct sunlight, excessive dust, or vibration.
Turn the System off and disconnect the power cord from the wall outlet,
• Install the System in a location with adequate ventilation to prevent internal
then call the store where you purchased this System. Using the System in this
heat buildup.
condition may cause a fire or electrical shock.
Power cord
• Do not handle the power cord with wet hands.
• A small amount of power is always consumed while the power cord is
Supplied accessories
connected to the wall outlet.
Check to make sure you have all of the supplied accessories.
• Do not pull on the cord to unplug the power cord. When unplugging the
power cord, always grasp and pull the plug so as not to damage the cord. If anything is missing, contact your dealer immediately.
•
To prevent malfunctions of the System Remote control RM-STHBC1J (× 1)
• • AC adaptor (AA-R1904) (× 1)
There are no user-serviceable parts inside. If anything goes wrong, unplug the
• AC power cord (× 1)
power cord and consult your dealer.
• Lithium coin battery CR2025 (× 1)
• Do not insert any metallic objects or liquids into the System.
– The battery has been installed in the remote control when shipped from
Safety precautions
the factory.
Avoid moisture, water, and dust
• Core filter (× 1)
Do not place the System in moist or dusty places.
• TV remote pass through cable (× 1)
Avoid high temperatures
• Double-sided adhesive tape (× 1)
Do not expose the System to direct sunlight and do not place it near any heating
• FM antenna (× 1)
devices.
When you are away
When away on holiday or for other reasons for an extended period of time,
disconnect the power cord from the wall outlet.
M
ises en garde, précautions et indications diverses
This device complies with Part 15 of the FCC Rules. Operation is subject to the
CAUTION: Proper Ventilation
following two conditions: (1) This device may not cause harmful interference,
To avoid risk of electric shock and fire, and to prevent damage, locate the
and (2) this device must accept any interference received, including
apparatus as follows:
interference that may cause undesired operation.
1. Front: No obstructions and open spacing.
Changes or modifications not expressly approved by the manufacturer for
2. Sides/Top/Back: No obstructions should be placed in the areas
compliance could void the user's authority to operate the equipment.
indicated by the dimensions in the illustration.
3. Bottom: Place on the level surface. Maintain an adequate air path for
Cet appareil est conforme à la partie 15 des règles de la FCC (Federal
ventilation by placing on a stand with a height of 10 cm (3-15/16") or more.
Communications Commission). Le fonctionnement est sujet aux deux
ATTENTION: Ventilation Correcte
conditions suivantes: (1) Cet appareil ne peut pas causer d'interférences
Pour éviter tout risque de choc électrique et d'incendie, placez l'appareil en
nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris
respectant ce qui suit:
des interférences qui peuvent causer un mauvais fonctionnement.
1. Avant: Rien ne doit gêner le dégagement.
Tout changement ou modification non expressément approuvés par le fabricant
2. Flancs/Dessus/Arrière: Aucun obstacle ne doit être placé dans les zones
pour conformité peut annuler l'autorité de l'utilisateur d'utiliser l'appareil.
indiquées par les dimensions dans l'illustration.
3. Dessous: Poser l'appareil sur une surface plate. Laissez suffisamment
For U.S.A.
d'espace pour que la ventilation puisse s'effectuer correctement en
Caution: Changes or modifications not expressly approved by party responsible
plaçant l'appareil sur un socle d'une hauteur de 10 cm ou plus.
for compliance could void the user's authority to operate the equipment.
Front / Face Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
15 cm (5-15/16")
in a residential installation. This equipment generates, uses and can radiate
15 cm
15 cm (5-15/16")
radio frequency energy and, if not installed and used in accordance with
(5-15/16")
10 cm (3-15/16")
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
CAUTION
installation. If this equipment does cause harmful interference to radio or
• Do not block the ventilation openings or holes. (If the ventilation openings or holes
television reception, which can be determined by turning the equipment off
are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
and on, the user is encouraged to try to correct the interference by one or more
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
of the following measures:
• When discarding batteries, environmental problems must be considered and local
– Reorient or relocate the receiving antenna.
rules or laws governing the disposal of these batteries must be followed strictly.
– Increase the separation between the equipment and receiver.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that
– Connect the equipment into an outlet on a circuit different from that to
no objects filled with liquids, such as vases, shall be placed on the apparatus.
which the receiver is connected.
ATTENTION – Consult the dealer or an experienced radio/TV technician for help.
• Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les
Pour les Etats-Unis
trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut
Attention: Les changements ou les modifications qui ne sont pas
ne pas être évacuée correctement de l'appareil.)
explicitement approuvés par la partie responsable de l'observance pourraient
• Ne placez aucune source de flamme nue, telle qu'une bougie, sur l'appareil.
mettre fin au droit de l'utilisateur d'utiliser le matériel.
• Lors de la mise au rebut des piles, veuillez prendre en considération les
Remarque: Cet appareil a été testé et il s'est avéré conforme aux limites
problèmes de l'environnement et suivre strictement les règles et les lois
applicables à un appareil numérique de classe B, en vertu de la Partie 15
locales sur la mise au rebut des piles.
des Règles de la FCC. Ces limites sont conçues de manière à assurer une
• N'exposez pas cet appareil à la pluie, à l'humidité, à un égouttement ou à des
protection raisonnable contre les interférences nuisibles dans une installation
éclaboussures et ne placez pas des objets remplis de liquide, tels qu'un vase,
résidentielle. Cet appareil produit, utilise et peut émettre une énergie de haute
sur l'appareil.
fréquence et, s'il n'est pas installé et utilisé en conformité avec les instructions,
il peut causer des interférences nuisibles aux communications radio. Il n'y a,
For U.S.A.
toutefois, aucune garantie que des interférences ne se produiront pas dans une
WARNING installation particulière. Si cet appareil cause effectivement des interférences
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO nuisibles à la réception de la radio ou de la télévision, ce qu'on peut établir
RAIN OR MOISTURE. en mettant l'appareil en marche et à l'arrêt, nous encourageons l'utilisateur à
tenter de corriger l'interférence par une ou plusieurs des mesures suivantes:
Pour les Etats-Unis
– réorienter ou déplacer l'antenne de réception;
AVERTISSEMENT
– accroître la séparation entre l'appareil et le récepteur;
POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS
– brancher l'appareil dans une prise ou un circuit autre que celui auquel le
EXPOSER CE APPAREIL À LA PLUIE OU À L'HUMIDITÉ.
récepteur est branché;
– consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir
de l'aide.
[European Union only]
[Union européenne seulement]
S T
pecifications roubleshooting
Output power 60 W (30 W per channel-measure at If you have a problem with this System, check this list for a possible solution
1 kHz Optical Digital In at full scale before calling for service.
sinewave), RMS at 4 Ω at 1 kHz, with
POWER
10% total harmonic distortion
Power does not come on.
Audio section
=
The power cord is not inserted securely. Plug it in securely.
Analog Input ANALOG: 1 Vrms/50 kΩ
The unit turns off suddenly.
Digital Input* DIGITAL 1 (OPTICAL) :
=
Auto power save function is on. Refer to "Activating/deactivating APS (Auto
–21 dBm to –15 dBm (660 nm ±30 nm)
Power Save)" in "Basic operation."
DIGITAL 2 (COAXIAL):
REMOTE CONTROL
0.5 Vp-p/75 Ω
The remote control does not work.
Speaker section
=
Pull out the insulation sheet.
Type: Bass-Reflex Type
=
Sunlight is shining directly on the remote sensor. Hide the remote sensor
Speaker: Woofer: 8 cm (3-3/16") cone × 4
from direct sunlight.
Tweeter: 2.5 cm (1") balance dome × 2
=
The path between the remote control and the remote sensor on the front
Power Handling Capacity: 30 W
panel is blocked.
Impedance: 4 Ω
=
Point the remote control at the remote sensor on the front panel.
Frequency Range: 82 Hz to 25 kHz
=
Signals cannot reach the remote sensor. Move closer to the unit.
Sound Pressure Level: 88 dB/W•m
=
The battery is exhausted. Replace the battery.
General
The remote control of the TV does not work.
Power Source (DC IN): DC19 V 3.37 A
=
If you install the unit near the TV, connect the TV remote pass through cable.
AC adaptor (AA-R1904): Input: AC 100 – 240 V , 50/60 Hz,
FM tuner
1.5 A – 0.9 A
Hard to listen to broadcasts because of noise.
Output: DC19 V 3.37 A
=
Electrostatic discharge from your body may cause noise. If this happens, turn
Power Consumption (in Standby mode): 0.50 W or less
off and on the unit again.
Dimensions (W × H × D): 900 mm ×98 mm × 107 mm
External components
(35-7/16" × 3-7/8" × 4-3/16")
Mass: 3.3 kg (7.3 lbs) No sound can be heard when DIGITAL 1 or DIGITAL 2 is selected as a
source.
=
Check the output setting of the connected digital components. Set the
Tuner
output setting as the PCM signal is outputted.
FM tuning range: 87.5 MHz – 108.0 MHz
Sound is turned off temporarily.
=
Press MUTING or VOLUME +/– to adjust the volume.
* Corresponding to Linear PCM only (with sampling frequency
— 32 kHz, 44.1 kHz, 48 kHz)
Designs & specifications are subject to change without notice.
• is a trademark of SRS Labs, Inc.
• StudioSound HD technology is incorporated under license from SRS Labs,
Inc.
• SURROUND: StudioSound HD by SRS Labs. SRS StudioSound HD™ provides
an immersive and engaging surround sound experience, while maintaining
steady volume and delivering rich bass and clear dialog.
• DRC: TruVolume by SRS Labs. TruVolume™ (designated as DRC) maintains
a steady volume for an enjoyable viewing experience.
G
etting started
DO NOT connect the power cord until all other connections have been made.
Preparing the remote control Installing the unit
When you use the remote control for the first time, pull out the insulation sheet. Install the unit on a flat and level surface to ensure the best sound quality.
If the range or effectiveness of the remote control decreases, replace the battery. • The sound may be affected depending on the location in which you install it.
To avoid such issues, change the location and orientation of the unit.
To replace the battery in the remote control
• For cathode-ray tube television (CRT):
Insert the battery into the remote control by matching the polarities (+ and –)
– The speakers of this unit are not magnetically shieled. If the unit has been
correctly.
installed near the TV, keep the unit away from the TV. Otherwise, color
Lithium coin battery distortion may occur on the TV.
(product number: CR2025)
CAUTION
NOTES
•
Do not drag or push the unit on the floor or table. Otherwise, the foot spacers at
• Store the battery in a place where
the bottom may peel off or drop from the unit.
children cannot reach. If a child
Installing on the wall
accidentally swallows the battery, consult
a doctor immediately. You can install the unit on the wall.
• To prevent the battery from overheating,
cracking, or starting a fire:
– Do not recharge, short, disassemble or heat the battery, or dispose of it in a
fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing away or saving it.
–
Do not poke the battery with tweezers or similar tools.
• Dispose of the battery in the proper manner, according to federal, state, and
local regulations.
CAUTION:
Wall
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
For USA-California Only
A: 6 mm – 7 mm (1/4" – 5/16")
This product contains a CR Coin Cell Lithium Battery which contains
B: Maximum 8.5 mm (3/8")
Perchlorate material—special handling may apply.
C: Maximum 6 mm (1/4")
Screw
See www.dtsc.ca.gov/hazardouswaste/perchlorate
D: φ 4 mm (screw diameter)
(not supplied)
E: Minimum 15 mm (5/8")
Connecting the FM antenna
CAUTION
FM antenna (supplied)
• The unit weighs approximately 3.3 kg (7.3 lbs). Sufficient care must be taken
when installing it on the wall to prevent any accidents caused by its falling off.
•
Use screws, which are compatible with the strength and material of the pillar or
wall to prevent the unit from falling off.
• Do not install the unit onto a plywood or plasterboard wall; otherwise, it will fall
and sustain damage.
• When installing the unit on the wall;
– Be sure to have it installed on the wall by qualified personnel.
– Care must be taken when selecting a location for installation on the wall.
Rear of the unit
Injury to personnel or damage to equipment may result if the installed unit
interferes with daily activities.
– AC adaptor should not be hanging/placed above any other items. Place the AC
Extend the FM antenna when connecting so that you can obtain the best adaptor on the flat floor only.
reception. – Recommended mounting surface: Wooden studs. If the mount is to be
NOTES
installed on any surface other than wooden studs, use suitable hardware
•
Make sure the antenna conductors do not touch any other terminals, connecting (which is commercially available).
cords or the power cord. Also, keep the antennas away from metallic parts of the
main unit, connecting cords, and the AC power cord. Otherwise, it could cause
poor reception.
• If you want to get a better reception, disconnect the supplied FM antenna, and
connect to an outdoor FM antenna (not supplied) using a 75 Ω wire with coaxial
type connector (IEC or DIN45325).
O
perations
Buttons and lamps on the front panel
1 2
3 4
Basic operation
Turning on/off the power Adjusting the volume
Press . Press VOLUME +/–.
NOTE CAUTION
• A small amount of power is consumed even when the power is turned off • Set the volume to the minimum level before starting any source. If the volume
(standby mode). During standby mode, the STANDBY indicator lamp on the front is set to a high level, the sudden blast of sound may damage your hearing and
panel lights up. Unplug the power cord from the AC outlet to turn the power off blow out the speakers.
completely.
• You can also turn on the power by pressing one of the input buttons (DIGITAL 1,
Turning off the sound temporarily
DIGITAL 2 or ANALOG) or FM.
Press MUTING.
• To restore the sound, press the button again or adjust the volume.
Activating/deactivating APS (Auto Power Save)
The System automatically turns off to save the power.
Changing the display brightness
Press and hold APS.
Press DIMMER.
Each time you press and hold the button, the indicator changes as follows:
APS ON (on) |\ APS OFF (off) Each time you press the button, the display brightness changes as follows:
DIM OFF (normal) \ DIM 1 (darker) \ DIM 2 (darkest)
• The System automatically turns off to save the power when one of the
following situations continues for 29 minutes:
For all sources: Making sound clearer
– The volume is set to 0
You can enjoy sounds recorded at low level—Dynamic Range Compression
–
Muting is activated (DRC).
For DIGITAL 1/DIGITAL 2:
Press DRC.
– When the optical cord or coaxial cord is not connected, or there is no signal.
Each time you press the button, the indicator and effect change as follows:
When one of the situations above occurs...
DRC OFF (off) |\ DRC ON (on)
The APS indicator is shown for 2 seconds every 1 minute and starts flashing 30
seconds before the System turns off.
Selecting the input source
Press one of the input buttons: DIGITAL 1 (for the optical
connection), DIGITAL 2 (for the coaxial connection), ANALOG FM.
or
FM
DIGITAL 1, DIGITAL 2, ANALOG or appears on the display.
Connecting the TV remote pass through cable
Connecting external components
If you install the unit near the TV, the unit may block the remote control signal
of the TV, and it may not be transmitted to the TV unit. Connect the TV remote You can connect an analog component to the ANALOG IN terminal and digital
pass through cable (supplied) to the unit for smooth signal transmission. components to the (OPTICAL) DIGITAL IN 1 and (COAXIAL) DIGITAL IN 2
As illustrated below, connect the TV remote pass through cable to the IR OUT terminals.
terminal. Move the cable to the remote sensor of your TV as closely as possible. You can also connect a subwoofer to the SUBWOOFER PRE-OUT terminal.
CAUTION
• Even if you connect the TV remote pass through cable to the unit, some TVs may
not receive the remote control signal of the TV, because some TVs use different
carrier frequency for the remote control.
Rear of the unit
Rear of the unit
Move it to the
remote sensor of
your TV as closely as
possible, then stick it
in any rear position
TV remote pass
of the unit
through cable
(supplied)
Red
Back
Double-sided
adhesive tape
(supplied)
(Dia. 3/16")
Using the core filter
To reduce interference, be sure to attach the provided core filters to the power
cord and the external component cord.
Run the cable through the core filter, and wind it firmly once inside. Close the DVD Player, etc.
core filter until it clicks shut. (not supplied)
To the terminal of the unit
DC power cord
Connecting the power cord
Connect the supplied AC adaptor to the DC IN jack on the unit. Then connect the
supplied AC power cord to the AC adaptor, and plug it in a wall outlet.
CAUTION
CAUTION
• Do not damage the cord by applying expressive force when winding.
• Disconnect the power cord before cleaning or moving the unit.
• To avoid the risk of fire and to prevent damage,
– Do not use any AC adaptors other than the one supplied.
– Do not use the supplied AC adaptor for other equipment.
1
• STANDBY indicator lamp lights up while the power is turned off.
2 FM/INPUT button
Press the button repeatedly to select the input source (DIGITAL 1,
DIGITAL 2, ANALOG and FM).
3 SURROUND button and SURROUND indicator lamps
5
• The indicator lamp lights up if a surround mode is on.
4 VOLUME +/– buttons
Adjusts the volume within the range of 0(VOL MIN) to 40(VOL MAX).
7
5 Remote sensor
Receives the signal from the remote control.
6 Display
Shows the volume level, the FM station's frequency that the unit is
receiving, the current source and the settings.
7 DRC indicator lamp
• DRC indicator lamp lights up if DRC is on.
6
Adjusting the sound level Listening to FM radio
You can adjust the bass and treble sound level within the range of –3 to +3.
Selecting the station
1
1
Press BASS/TREBLE repeatedly to select the sound you want to Press FM.
adjust. 2
Press UP or DOWN to select the station.
– BASS: Adjusts the bass sound level.
Press and hold 4 or ¢ for 2 seconds, then release it to change the
•
– TREBLE: Adjusts the treble sound level.
2 frequency automatically until a station of sufficient signal strength is tuned in.
Press UP or DOWN to adjust the level.
Presetting stations
NOTE
You can preset up to 30 stations.
• The change in the bass and treble sound level of the speakers differ depending
on the incoming signal of the input source. Auto preset
Press and hold A.PRESET for 2 seconds
Using the surround mode
Stations are presetted automatically.
Manual preset
You can listen to a more realistic sound than stereo sound using surround.
• If you want to preset stations manually, press MEMORY while tuning into a
Press SURROUND.
station you want to preset. Then press UP/DOWN to select a preset number.
Each time you press the button, the indicator and effect change as follows:
Store the station by pressing MEMORY.
SURR OFF (off) |\ SURR ON (on)
Improving the FM reception
When an FM stereo (FM) broadcast is hard to receive or noisy, select the
monoural reception (MONO) mode.
Press FM MODE.
• To restore stereo reception, press FM MODE again.
* Stereo reception is only available, if there is enough signal strength.
Subwoofer
(not supplied)
RCA pin plug cord
(not supplied)
White
Digital optical cord
RCA pin plug cord
(not supplied)
(not supplied)
Digital coaxial
cord (not
supplied)
TV, etc. (not supplied)
(power) button and STANDBY indicator lamp