Page 1 HERA51 Mobile POS Android 8.1, Oreo Version 1.06...
Page 2 The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement. CIPHERLAB logo is a registered trademark of CIPHERLAB CO., LTD.. All other brands, products and services, and trademark names are the property of their registered owners. The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement.
Page 3: Important Notices
IMPORTANT NOTICES FOR USA FCC ID: 2ASPU-HERA51 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 4: Sim Cards Using Information For Verizon And At&T Cellular Service
You can use any of your already activated SIM cards that have service on the HERA51. Please note the HERA51 uses MicroSIM cards. In the event that you have a NanoSIM card, you’ll need to utilize a SIM card adapter to convert them into MicroSIM in order to fit the device.
Page 5: For Product With Laser
Important Notices FOR PRODUCT WITH LASER  This laser component emits FDA / IEC Class 2 laser light at  the exit port. Do NOT STARE INTO BEAM DIRECTLY.  Do not aim the beam at the eyes.  Any adjustments or performance excluding those specified herein may result in hazardous laser light exposure.
Page 6: Important Safety Instructions And Warning For Li-Ion/Polymer Battery
GENERAL GUIDELINE AND WARNING  Use specific Lithium Polymer/Li-ion charger from CipherLab only. Failure to do so may cause fire, which may result in personal injury and property damage.  Never charge batteries unattended. When charging Lithium Polymer/Li-ion batteries, you should always remain in constant observation to monitor the charging process and react to potential problems that may occur.
Page 7: Charging Process
During discharge and handling of batteries, do not exceed 45 . STORAGE & TRANSPORTATION  CipherLab battery is charged in manufacturing to around 30% of its full capacity. It is a good capacity for long-term storage & transportation.  Battery should NOT be stored in full-charged or full-discharge state; otherwise it will damage battery permanently.
Page 8: To Use, Handle, And Dispose Battery
HERA51 Mobile POS TO USE, HANDLE, AND DISPOSE BATTERY  For Li-ion / Li-polymer battery, it is normal to balloon, expand, or swell after one year or 500 cycles (full charge-discharge cycles). Although we guarantee it will NOT cause any damage, it can’t be used again and must be disposed at once, therefore we strongly recommend to...
Page 9: Safety Precautions
 Do not use any pointed or sharp objects against the screen surface.  Do not use the styluses which are not supplied or approved by CIPHERLAB CO., LTD., to prevent possible scratches to the touch screen.  Water residue on the touch screen may cause abnormal behaviors or the fall of its sensitivity levels.
Page 10: Battery
1) Please do not use your device while continuously connected with a power supply or cradle for charging. If you need to use your HERA51 Mobile POS with a power supply or cradle continuously connected, be sure to turn on “Balance...
Page 11: Scanner
Important Notices SCANNER  Scan a 1D barcode 1) Open ReaderConfig and tap Scan Test on the menu bar. 2) Aim the scanning window at the barcode to read. Move the device, having the barcode located in the center of the scanning area. 3) Press any of the two side triggers.
Page 12: Care & Maintenance
HERA51 Mobile POS CARE & MAINTENANCE  Damage may be done to the mobile POS if it is exposed to extreme temperatures or soaked in water.  When the body of the mobile POS gets dirty, use a clean, wet cloth to wipe off dust and debris.
Page 13: E-Label
Important Notices E-LABEL - 13 -...
Page 14: Release Notes
Update Section 3.4 “Enterprise Settings”. Update Section 3.6 “OS Update”. Update Section 3.8.3 “Welcome Wizard”. Add “Cipherlab Proprietary Settings” to Section 4.2.3 “Wi-Fi Preferences”. Remove Chapter 6 “Using Reader Configuration Utility”. (Please refer to “ReaderConfig User Guide for Android”) 1.05...
Page 15: Table Of Contents
HERA51 Mobile POS CONTENTS IMPORTANT NOTICES........................- 3 - For USA ............................- 3 - SIM Cards Using Information for Verizon and AT&T Cellular Service ........- 4 - For Product with Laser ........................- 5 - Environment ..........................- 5 - Specific Absorption Rate (SAR) information ................
Page 16 1.2.1. Charge Mobile POS ....................32 1.2.2. Wired Data Transmission ..................36 1.2.3 Using Wireless Networks ..................37 USING THE HERA51 MOBILE POS ....................38 2.1. Battery ........................39 2.1.1. Battery Status Indicators..................40 2.1.2. Monitor Battery Level .................... 42 2.1.3.
Page 17 CONTENTS BASIC OPERATION .......................... 99 3.1. Home Screen ....................... 100 3.1.1. Customize Home Screen ..................100 3.2. Status Bar ......................103 3.2.1. Icons on Status Bar ..................... 103 3.2.2. Open Quick Settings Menu ................. 105 3.2.3. Open Notifications Drawer .................. 108 3.3.
Page 18 HERA51 Mobile POS 4.3. Use Bluetooth ...................... 155 4.3.1. Bluetooth Profiles ....................155 4.3.2. Turn On Bluetooth ....................156 4.3.3. Change Bluetooth Name ..................158 4.3.4. Pair Bluetooth Devices ..................159 4.3.5. Unpair Bluetooth Device ..................160 4.4. Use Near Field Communications ................ 161 4.4.1.
Page 19: Introduction
Introduction INTRODUCTION The HERA51 Mobile POS, powered by Android 8.1 Oreo, is light-weight, easy to use, providing powerful and handy tools for the purpose of delivering flexibility in customization. Specifically designed to work as an industrial PDA, it provides rich options of data collection, voice and data communication, long-lasting working hours, and so on.
Page 20: Features
HERA51 Mobile POS FEATURES  Android 8.1 Oreo operating system with a powerful Qcta-core 1.8GHz processor  16GB (64GB by request) eMMC flash memory to store OS and software programs  2GB (4GB by request) LPDDR3 SDRAM to store and run programs, as well as store program data ...
Page 21: Accessories
Charging cradle RELATED DOCUMENTATION Log in to GoBetween to access related documentation about the HERA51 Mobile POS from the CipherLab Central Service (CCS) platform. Download the GoBetween desktop or mobile device application, or launch the GoBetween Lite web application from the following site:...
Page 22: Quick Start
HERA51 Mobile POS Chapter 1 QUICK START This chapter helps you get ready for starting using the mobile POS. IN THIS CHAPTER 1.1 Overview ..................23 1.2 Charging & Communication ............32...
Page 23: Overview
Quick Start 1.1. OVERVIEW Description Description Phone Receiver Status LEDs Light Sensor & Proximity Sensor Touch Screen Microphone Charging & Commnuication Port Loudspeaker Power Button Side Trigger Key Camera Flash Camera Battery (with Cover) Hand Strap Hole Card Reader Volume Keys Battery Latch Scan Window Magnetic Strip Card Reader Slot...
Page 24: Installing/ Removing Battery
HERA51 Mobile POS 1.1.1. INSTALLING/ REMOVING BATTERY For shipping and storage purposes, the mobile POS and the main battery are saved in separate packages. Note: Any improper handling may reduce the battery life. INSTALL MAIN BATTERY To install the main battery, please: 2.
Page 25 CipherLab approved 3.8V 4000mAh/3.75V 5300mAh (Standard/Extended) Battery Pack rechargeable Li-ion CipherLab proprietary Approx. 4 hours (4000mAh) / 6 hours (5300mAh) via adapter at 25 Charging Time For the first time charging the main battery, please charge it for at least 8 to 12 hours.
Page 26: Installing Sim Card, Sam Card And Memory Card
1.1.2. INSTALLING SIM CARD, SAM CARD AND MEMORY CARD The HERA51 mobile POS is equipped with either one SIM card slot, two SAM card slots and one memory card slot, or two SIM card slots, one SAM card slot, and one memory card slot.
Page 27 Quick Start 3) After the chamber is revealed, insert SIM cards, the SAM card and the microSD card into their respective sockets. Close and push back the hinged cover till a click sounds. To Install the Cards: 1) Slide the hinged cover back. 2) Swing the top to open.
Page 28 HERA51 Mobile POS REMOVE CARDS 1) Remove the battery. 2) Remove the inner lid. 3) Unlock the card hinge cover and remove the card. 4) Mount the inner lid and the battery.
Page 29: Power On/Off Mobile Pos
Quick Start 1.1.3. POWER ON/OFF MOBILE POS POWER ON To power on the mobile POS, press and hold the power button located on the upper right side of the device. The mobile POS will turn on and show Home Screen after splash screen.
Page 30: Homescreen Selection
HERA51 Mobile POS 1.1.4. HOMESCREEN SELECTION Upon the first time you launch the system, a Select Home app window will pop up to request your immediate choice of home screen. By selecting “AppLock”, you will directly enter AppLock application (please refer to AppLock User Guide for detailed instructions on AppLock settings) to start configuring the interface provided to normal users of this device;...
Page 31: Using Hardware Buttons
Quick Start 1.1.5. USING HARDWARE BUTTONS On the bottom of the mobile POS are three hardware buttons that deliver the following functions: Button Function Description Returns to the previous screen or closes the active Back button window or keyboard. Home button Displays the Home screen.
Page 32: Charging & Communication
HERA51 Mobile POS 1.2. CHARGING & COMMUNICATION 1.2.1. CHARGE MOBILE POS The main battery may not be charged to full for shipment. When you first receive the kit package, you will need to charge the main battery to full before using the mobile POS. You may use the Snap-on Charging Cable or Charging Cradle along with a power adapter to charge the mobile POS.
Page 33 Quick Start OPERATION ON BATTERY POWER When 802.11a/b/g/n/ac, GSM/GPRS/EDGE/WCDMA/HSPA/HSPA+/LTE CAT 6, Bluetooth v4.1 & v2.1+EDR and GPS are all enabled on battery power, the main battery level will drop down substantially. Prolonged use of the display and continued scanning of barcodes will also affect battery level.
Page 34 HERA51 Mobile POS While the device battery is being charged, the LED indicators on mobile POS will indicate charging status. LED Indicator Status Description Charging in progress Red, solid Charging error Red, blink Charging Status Charging completes Green, solid The cable is not correctly connected...
Page 35 2) Connect the adapter to the Cradle, and plug the other end into an electrical outlet. The status of the mobile POS charging is shown on the device itself; while the LED indicator on HERA51 Charging Cradle shows the status of battery charging as below: Cradle LED Indicator...
Page 36: Wired Data Transmission
HERA51 Mobile POS 1.2.2. WIRED DATA TRANSMISSION Use the Snap-on cable to connect the mobile POS to your PC for data transmission. 1) Connect your device to the computer with the supplied Snap-on cable. 2) Swipe down from the status bar to reveal Notifications Drawer.
Page 37: Using Wireless Networks
Quick Start 1.2.3 USING WIRELESS NETWORKS The mobile POS supports widely applied wireless technologies including Bluetooth v4.1 & v2.1+EDR, 802.11 a/b/g/n/ac, and is able to send/receive data in real time in an efficient way. Select GSM/GPRS/EDGE/WCDMA/HSPA/HSPA+/LTE CAT 6 modules embedded for a total wireless solution for data and voice communication.
Page 38: Using The Hera51 Mobile Pos
HERA51 Mobile POS Chapter 2 USING THE HERA51 MOBILE POS This chapter walks you through the fundamental usage and features of this device. IN THIS CHAPTER 2.1 Battery ..................39 2.2 Memory ..................53 2.3 Touch Screen ................64 2.4 Notifications .................. 70 2.5 Date and Time ................
Page 39: Battery
Using the HERA51 Mobile POS 2.1. BATTERY  Main Battery The mobile POS is powered by a rechargeable 3.8V / 4000 mAh Li-ion battery pack. It takes approximately 4 hours to charge it to full from the power adaptor (for the first time charging the main battery, please charge it for at least 8 to 12 hours).
Page 40: Battery Status Indicators
HERA51 Mobile POS 2.1.1. BATTERY STATUS INDICATORS The main battery pack is the only power source for the mobile POS to work. Therefore, when the main battery level goes low, you need to replace the battery pack with a charged one or charge it as soon as possible.
Page 41 Using the HERA51 Mobile POS Note: When the mobile POS is fully charged and battery level reaches 100%, the battery icon will change from to indicate charging is completed. Warning: (1) Once the battery level drops below 15%, the low battery notification will be displayed on the screen.
Page 42: Monitor Battery Level
HERA51 Mobile POS 2.1.2. MONITOR BATTERY LEVEL MAIN BATTERY LEVEL The main battery is the only source that feeds the mobile POS to work. It also supplies the backup battery on the main board in order to retain the data stored in DRAM. When main battery level gets low, recharge it or replace it as soon as possible.
Page 43 Using the HERA51 Mobile POS On Battery screen, simply switch on “Battery saver” or tap on it to enter “Battery saver” page to switch it on and set choose when to have this mode automatically activated. Also, you can swipe down from the status bar to reveal Quick Settings Panel or Quick Settings...
Page 44 HERA51 Mobile POS BATTERY OPTIMIZATION With Battery optimization enabled for the applications, you can make sure they stay inactive when your device is idle or when they have not been used for days and then select “Battery optimization” 1) On Battery screen, tap More 2) On the dropdown list, select “All apps”, all the applications will be optimized by this function by...
Page 45 Battery. LOW SUB BATTERY ALERT When the main battery’s power is drained out, HERA51 Mobile POS will automatically suspend by backup battery’s power for 30 minutes. When backup battery’s power is low, the “Low Sub Battery” notification will remind you to connect the device with an external power source to charge it immediately.
Page 46: Replace Main Battery
BATTERY SWAP HERA51 Mobile POS's backup battery supplies system power during battery swap. When the battery (with cover) is removed, the system will enter suspend mode and not wake up until battery cover is put back and the power button is pressed.
Page 47 DO NOT replace the main battery when backup battery’s power is low. Please connect HERA51 Mobile POS with the external power source to charge it till the “Low Sub Battery” notification icon disappears from the status bar. Once the “Low Sub Battery”...
Page 48: Power Management
HERA51 Mobile POS 2.1.4. POWER MANAGEMENT For any portable device, power management is a critical issue especially when you are on the road. Below are some tips to help you save battery power. Warning: Using backlight, wireless connectivity, and peripheral devices on battery power will substantially reduce battery power.
Page 49 Using the HERA51 Mobile POS ENTER AIRPLANE MODE You can enable Airplane mode to have all the wireless radios (including call functions, data connections such as Bluetooth, Wi-Fi and 3G/4G) on your mobile POS turned off, which will considerably reduce the power consumption of your battery.
Page 50: Battery Precautions
HERA51 Mobile POS with a power supply or cradle, be sure to turn on “Balance Mode”. BATTERY MODE SELECTION If you need to use HERA51 Mobile POS while charging, or if the device needs to be connected with the power supply for charging all the time, it is suggested that enabling “Balance Mode” for battery life.
Page 51 Using the HERA51 Mobile POS 3) Tap to select “Balance Mode” or “Performance Mode”. Mode Description Balance between working hour and Balance Mode battery life. Better & extra 10% to 20% working hour Performance Mode performance, but might affect battery life.
Page 52 HERA51 Mobile POS BATTERY TEMPERATURE ANOMALY High ambient temperature or keeping using HERA51 Mobile POS while charging might results in battery temperature rises. HERA51 Mobile POS will automatically suspend charging battery or shut down for safety purpose. Once the battery temperature cools down to normal temperature, battery charging could be proceeded again.
Page 53: Memory
When choosing an SD card for best compatibility and performance with HERA51, please make sure of the capacity you need. For the use of SDXC card, please use a new card and make sure it has not been used in other host devices (computers, cameras, or readers).
Page 54: Check Memory Usage
HERA51 Mobile POS 2.2.1. CHECK MEMORY USAGE The memory manager can offer a glance of how the device is using its RAM. ENABLE DEVELOPER OPTION To check the memory usage, you have to enable “Developer Option” : 1) Go to...
Page 55 Using the HERA51 Mobile POS CHECK MEMORY USAGE App Drawer (All Apps) | Settings | Developer Option | Memory to enter memory manager screen. On the main screen, it tells you not only the used and free memory space of the RAM, but how your pattern of usage has impacted the device’s overall performance.
Page 56: Manage Storage Space
HERA51 Mobile POS 2.2.2. MANAGE STORAGE SPACE To your Android device, the SD card can serve as an extension of your device’s internal storage (which comes as 16 GB of flash memory to store the OS, applications and files) other than a portable storage place.
Page 57 Using the HERA51 Mobile POS SET UP SD CARD AS PORTABLE STORAGE Using SD card as a portable device allows you to treat it as a USB disk, by swapping it between your Android device and the computer to easily transfer files. This is quite handy when there is a need to offload files that are taking up too much storage space.
Page 58 HERA51 Mobile POS To start: 1) Insert the SD card. A notification icon indicating that an SD card is detected will be shown in the status bar; swipe down from the status bar and tap on “SET UP”. 2) Tap “Use as portable storage” and then “NEXT”.
Page 59 Using the HERA51 Mobile POS TRANSFER PHOTOS & MEDIA BETWEEN THE DEVICE & PC To transfer photos and media between this device and PC when the mounted SD card is set as portable storage, please: 1) Connect your mobile POS with PC with supplied USB cable.
Page 60 HERA51 Mobile POS CONVERT THE SD CARD TO INTERNAL STORAGE You can always convert the SD Card from portable storage to internal storage. On Storage screen, tap the SD card. Before you start, make a backup of the files on this disk if you would like to keep them.
Page 61 Using the HERA51 Mobile POS SET UP SD CARD AS INTERNAL STORAGE Using SD card as internal storage allows you to extend your existing device storage and to store huge applications. This SD card will be reformatted and encrypted with a file format that is not readable by another device.
Page 62 HERA51 Mobile POS To start: 1) Insert the SD card. A notification will pop up indicating that an SD card is detected tap “SET UP”. 2) Tap “Use as internal storage” and then “NEXT”. 3) Tap “ERASE & FORMAT” to format this card.
Page 63 Using the HERA51 Mobile POS CONVERT THE SD CARD TO PORTABLE STORAGE You can always convert the SD Card from internal storage to portable storage. 1) On Storage & USB, tap the SD card. Before you start, make a backup of the files on this disk if you would like to keep them.
Page 64: Touch Screen
HERA51 Mobile POS 2.3. TOUCH SCREEN The mobile POS comes with a 4.7” transmissive LCD with 1280 by 720 pixels resolution (HD). The LED backlight of the screen, which helps ease reading under dim environments, can be controlled manually and automatically.
Page 65: Screen Rotation
Using the HERA51 Mobile POS 2.3.2. SCREEN ROTATION By default, the device automatically rotates the screen to when you turn the device sideways. To switch this function on or off: 1) Go to App Drawer (All Apps) | Settings | Display 2) Tap Advanced for more display settungs, and switch on or off Auto-rotate screen.
Page 66 HERA51 Mobile POS REMOVE AUTO-RITATE FROM QUICK SETTINGS MENU & DISPLAY SETTINGS ou can remove the Auto-rotate switch icon on Quick Settings menu to minimize the possibility of accidentally turning on the auto-rotation function: 1) Use two fingers to swipe down from the top of the screen to open Quick Settings menu.
Page 67 Using the HERA51 Mobile POS Go to App Drawer (All Apps) | Settings | Accessibility and switch off Auto-rotate screen. By doing so, the auto-rotation option will be hidden in Settings | Display Note: Auto-rotation is not supported for certain applications. Without enabling “Allow Home Screen...
Page 68: Screen Timeout Settings
HERA51 Mobile POS 2.3.3. SCREEN TIMEOUT SETTINGS Go to App Drawer (All Apps) | Settings | Display | Advanced | Sleep. Select the time lapse for screen timeout.
Page 69: Text Size & Display Size
Using the HERA51 Mobile POS 2.3.4. TEXT SIZE & DISPLAY SIZE To change text size, please go to App Drawer (All Apps) | Settings | Display Advanced | Font size Tap the small A icon or the large A icon to select the font size between Small, Default, Large and Largest.
Page 70: Notifications
HERA51 Mobile POS 2.4. NOTIFICATIONS 2.4.1. STATUS LED Two LED indicators located above the touch screen provide information about charging status, scanner light beam, and scanner "Good Read" during data collection Indicator Status Description Green, solid Charging complete Red, solid...
Page 71: Audio
Using the HERA51 Mobile POS 2.4.2. AUDIO The speaker is used to play sounds for events, or play audio files. In addition, it can be programmed for status feedback. In noisy environments, you may consider connecting a headset instead. The mobile POS also supports using Bluetooth headsets.
Page 72 HERA51 Mobile POS SOUND SETTINGS Go to App Drawer (All Apps) | Settings | Sound for more sound settings “Ring volume” is not adjustable when “Do not disturb” mode is on. DISABLE UNWANTED NOTIFICATIONS WITH “DO NOT DISTURB” You can temporarily disable specific notifications (vibration or sound) using “Do Not Disturb” in Quick Settings menu.
Page 73 Using the HERA51 Mobile POS Total Silence Alarm Only Priority Only Alarm Reminders Adjustable (Default:ON) Events Adjustable (Default:ON) Adjustable Incoming Calls (Default:From Contacts Only) Messages Adjustable (Default:OFF) Music, Video, Game or Media In-Call Tap “MORE SETTINGS” to enter “Do Not Disturb preferences” page for detailed settings:...
Page 74: Date And Time
HERA51 Mobile POS 2.5. DATE AND TIME By default, the mobile POS automatically synchronizes the date and time to the WWAN network (if connected). To set the date and time manually: 1) Tap App Drawer (All Apps) | Settings | System | Date &...
Page 75 Using the HERA51 Mobile POS 4) Tap Set date to select the correct month, date and year. Tap OK to save 5) Tap Set time to set the correct time. Tap OK to save 6) Tap Select time zone to select the correct time zone from the list 7) Tap “Use 24-hour format”...
Page 76: Language & Keyboard Input
HERA51 Mobile POS 2.6. LANGUAGE & KEYBOARD INPUT App Drawer (All Apps) | Settings | System | Language & input to change the system language, default keyboard type, and configure keyboard input and speech settings. 2.6.1. CHANGE DISPLAY LANGUAGE To change display language: 1) On Language &...
Page 77 Using the HERA51 Mobile POS 2) Press and hold your desired system language to change its sorting order to the 1st by dragging. Once it is released, the new language setting will immediately be applied. DELETE LANGUAGE in the upper right corner and tap “Remove” option; select the language to delete. Please...
Page 78: On-Screen Keyboard
HERA51 Mobile POS 2.6.2. ON-SCREEN KEYBOARD Tap a text input field to automatically open an on-screen keyboard. The virtual keyboard will vary depending on the data type (text or numbers) this field requires. SELECT & CHANGE KEYBOARD (INPUT METHOD) On Language & input screen, select Virtual Keyboard to manage the installed keyboards by...
Page 79 Using the HERA51 Mobile POS The default keyboard “Gboard” supports multilingual typing. To have more options of key layouts, for example, Japanese, you can 1) On Language & input screen, tap on Virtual Keyboard, select Gboard, and then Languages 2) On Languages screen, tap on “ADD KEYBOARD”...
Page 80 HERA51 Mobile POS 3) Swipe or input the keyword to search for your desired language, and tap on it to select the keypad layouts 4) Return to Languages screen, and Your Keyboard language and layouts now lists more languages below...
Page 81 Using the HERA51 Mobile POS CHANGE KEYBOARD (INPUT METHOD) to open “Change Keyboard” menu and Expand your Gboard and long press space key or select your desired input language Simply tap to cycle through the options:...
Page 82 HERA51 Mobile POS If there’s any other keyboards installed by you, please long press space key or of Gboard till “Change Keyboard” menu appears and select the keyboard you need. Or swipe down from the status bar to open Notifications Drawer and tap “Change Keyboard” notification to change it.
Page 83 Using the HERA51 Mobile POS By taping on the settings buttons, you can: Button Description Figure To enter Gboard setting page for further settings. To show the emoji keyboard. to return to the text keyboard. To adjust the keyboard layout to meet your need.
Page 84 HERA51 Mobile POS EDIT KEYBOARD LANGUAGE (INPUT METHOD) The keyboard language you enabled in Gboard can be edited from Language & input Virtual keyboard | Gboard | Languages , and on Languages screen, you can add/delete keyboard languages, and change the keyboard language sorting order.
Page 85 Using the HERA51 Mobile POS To change the keyboard language sorting order, keep pressing the language, drag it upward or downward to change its sorted position, and then release to have it placed. Return to the previous screen, and tap on any text input field to expand Gboard to reveal “Change Keyboard” menu by button or tapping “Change Keyboard”...
Page 86 HERA51 Mobile POS To delete keyboard language, simply tick the check box of the language(s) to be removed, and tap on the delete icon at the upper-right corner. Please note that you should keep at least one keyboard language. Step 2: Tap on delete icon.
Page 87 Using the HERA51 Mobile POS ENTER NUMBERS AND SYMBOLS The appearance of the switch button to numeric or symbol keyboard may vary; the example below demonstrates how to use the switch key to access your desired numeric or symbol keyboards from the default Gboard keyboard.
Page 88 HERA51 Mobile POS ENTER UPPERCASE LETTERS Tap the shift key once to switch it to be , and tap a character key to enter an uppercase letter. The letters will return to lower case once an uppercase letter is entered.
Page 89: Sound And Volume
Using the HERA51 Mobile POS 2.7. SOUND AND VOLUME Use the volume buttons on the left side of the mobile POS to adjust system and ringer volume.
Page 90: Button Assignment
HERA51 Mobile POS 2.8. BUTTON ASSIGNMENT App Drawer (All Apps) | Settings | System | Button Assignment assign specific functions to the following programmable keys: Volume Up Volume Down Right Scan (side key) Soft Home Soft Back Soft App Switch Soft Search After redefining the programmable keys, the changes will immediately take effect.
Page 91 Using the HERA51 Mobile POS ASSIGN KEYCODE Tap the key you would like to assign. A screen opens showing a list of available keycodes or applications. On the Keycodes tab page, scroll down to view the entire list of keycodes, and tap a...
Page 92 HERA51 Mobile POS ASSIGN APPLICATION Tap the key you would like to assign. Tap the Apps tab page to open a list of available applications. Scroll down to view the entire list of applications, and tap an application to apply.
Page 93 Using the HERA51 Mobile POS ASSIGN INTENT You can make use of the intent (the specific intent string should be input beforehand in the configuration xml file on your device) to assign a hardware key to launch a specific application.
Page 94 HERA51 Mobile POS To share this exported file with other devices, please make sure the filename is not renamed. Tap the file name till the “Action” menu appears, and select “Send” and then select a file-sharing method from “Send with” menu.
Page 95 Using the HERA51 Mobile POS To import the configuration file to be used in Programming keys, make sure the file is saved in the root folder of the device’s internal storage with the file name keys_config.txt. On the Button and then “Import”. The new setting will be immediately Assignment screen, tap on More applied to the keys.
Page 96: Data Capture
HERA51 Mobile POS 2.9. DATA CAPTURE 2.9.1. BARCODE READER A selection of scan engines is available for delivering flexibility to meet different requirements. Depending on the scan engine integrated, the mobile POS is capable of scanning barcodes of a number of symbologies that are enabled by default while running the ReaderConfig application. If you need to scan barcodes that are encoded in a different symbology, enable the symbology first.
Page 97: Card Reader
Using the HERA51 Mobile POS 2.9.3. CARD READER HERA51 Mobile POS equiped with a card reader which is applicable for chip card, magnetic stripe card, and proximity card. FOR PROXIMITY CARD FOR CHIP CARD...
Page 98 HERA51 Mobile POS FOR MAGNETIC STRIPE CARD LED STATUS AND AUDIBLE BEEPER DURING TRANSACTIONS AND OPERATION Device Status 4 LED’s Audible Beeper Run Mode Left LED Flash 300ms on/5s off All 4 LESd flash Once Contactless Read Successful 1 longer beep...
Page 99: Basic Operation
Chapter 3 BASIC OPERATION This chapter describes the basic skills to work with the HERA51 Mobile POS, for instance, on how to operate the home screen, check system statuses and manage notifications. The add-on utilities for applications regarding data collection, processing, and transmission are introduced in the following chapters.
Page 100: Home Screen
HERA51 Mobile POS 3.1. HOME SCREEN When the mobile POS is fully charged, press the Power key for three seconds to turn on the mobile POS. A locked screen will appear. Slide the lock button upward to unlock the screen.
Page 101 Basic Operation ARRANGE THE SHORTCUTS AND WIDGETS ON HOME SCREEN To move or remove a shortcut/widget, on the home screen you would like to customize, tap and hold it to enter layout edit mode, an option “X Remove” will appear on top of the screen, to which you can drag the unwanted shortcut/widget to remove it.
Page 102 HERA51 Mobile POS CHANGE HOME SCREEN WALLPAPER 1) Tap and hold any empty spot on the home screen. 2) Tap Wallpapers in the menu that appears, and select the app you would like to use. 3) Select an image to apply as the wallpaper.
Page 103: Status Bar
Basic Operation 3.2. STATUS BAR The left side of the status bar shows notification icons, and the right side of the status bar shows status icons. 3.2.1. ICONS ON STATUS BAR STATUS ICONS Icon Description Bluetooth is on. The device has been connected to a Bluetooth device. The device is currently connected to a Wi-Fi network and performing data transmission.
Page 104 HERA51 Mobile POS NOTIFICATION ICONS Icon Description USB debugging mode is enabled on this device The device is performing data synchronization. There is an upcoming event. The device is downloading data. The device is uploading data. An open Wi-Fi network is available.
Page 105: Open Quick Settings Menu
Basic Operation 3.2.2. OPEN QUICK SETTINGS MENU The status icons are related to essential settings regarding the device’s remaining power, Bluetooth status or Wi-Fi connectivity status. The status bar offers a quick access for you to easily make adjustments of the settings. To open Quick Settings menu, use you two fingers, swipe from the Quick top to the bottom of the screen.
Page 106 HERA51 Mobile POS EDIT QUICK SETTINGS MENU To customize Quick Settings Menu, please: 1) Click “EDIT” icon to get into Edit page. 2) Remove: To remove certain item, please tap on and hold the icon to be removed, and drag it to the light gray area and then release it.
Page 107 Basic Operation To reset Quick Settings Menu, please 1) Tap to enter Edit page icon in the upper-right corner, and tap “Reset” 2) Tap More...
Page 108: Open Notifications Drawer
HERA51 Mobile POS 3.2.3. OPEN NOTIFICATIONS DRAWER The notifications icons on status bar inform you of the new events such as incoming calls, messages or USB connection. CHECK OUT NOTIFICATION To check out details of the events, swipe down from the...
Page 109 Basic Operation SNOOZE NOTIFICATION To temporarily dismiss the notification, you may snooze the notification by sliding it to the right or the left slightly and slowly till the reschedule icon and the settings icon show up. Tap on the reschedule icon to set the reminder while tapping on the settings icon more settings.
Page 110 HERA51 Mobile POS CLEAR NOTIFICATION To dismiss a single notification, simply swipe the notification right or left. You can also dismiss all notifications at a time by tapping “CLEAR ALL”. Ongoing notifications and notifications that require subsequent activity to be cleared will remain on the list.
Page 111: Manage Applications
Name Description An application which give the brief introduction about A-Demo CipherLab’s applications. Users can launch those apps by tapping “START” on the app’s introduction page. Airlock Browser is a modern, feature rich, highly configurable Airlock Browser web browser that allows mobile workers to be more productive.
Page 112 HERA51 Mobile POS Icon Name Description A one-to-one video call application developed by Google. An application to control whether the status bar could be Enterprise Settings pulled down or not. Browses and manages files on the local storage and storage File Manager card.
Page 113 Basic Operation Icon Name Description Settings Opens settings to configure the mobile POS. A simple and easy application which transform your device Signature Capture into a signature pad for user to draw the signature. An application for quickly open or close virtual keyboard by SIP Controller tapping on the floating button.
Page 114: Current Applications
HERA51 Mobile POS 3.3.2. CURRENT APPLICATIONS Tap the Recent Apps button . The screen will show a list of recently used applications. On this screen, you can: SWITCH BETWEEN APPLICATIONS Swipe up or down to cycle through the listed applications; tap on your desired one to open it on the screen.
Page 115: Enterprise Settings
Basic Operation 3.4. ENTERPRISE SETTINGS The app “Enterprise Settings” is for setting whether the status bar could be pulled down or not. “Enterprise Settings”. Please go to App Drawer (All Apps) and tap on LOCK QUICK SETTINGS By tapping on the switch of “Lock quick settings”, you can enable or disable the status bar on the top of the screen.
Page 116 HERA51 Mobile POS DOZE MODE “Doze Mode” is enabled by default. Please refer to https://developer.android.com/training/monitoring-device-state/doze-standby for details. VERSION The version information about Enterprise Settings is listed right below “Doze Mode”.
Page 117: Suspend & Lock
SUSPEND HERA51 Press the power button to immediately suspend the mobile POS. The mobile POS will also automatically get into suspend when the time interval set in...
Page 118: Lock Device
HERA51 Mobile POS 3.5.2. LOCK DEVICE Setting a screen lock allows you to protect your personal data on this device while the device is not at your hand. With various types of screen lock available and Smart Lock, you can not only enjoy the benefits of this function but also great convenience.
Page 119 Basic Operation By selecting a pattern, PIN, or Password method, you can access advanced settings and Smart Lock to customize personal lock settings. SCREEN LOCK SETTINGS Except of setting “None” for screen lock, you can tap on the settings icon next to “Screen lock”...
Page 120 HERA51 Mobile POS Item Description None Disable screen lock. Switch to make the unlock pattern you are drawing to be visable or Make pattern visable invisable. This function only works when setting pattern as screenlock. Tap to set the time interval to automatically lock the screen after Automatically lock screen timeout.
Page 121: Os Update
App Drawer (All Apps) | Settings | System | About phone | System updates 2) A dialog pops up asking you to input the password for system update. Please contact with support@cipherlab.com.tw for the password. Enter the password and tap OK...
Page 122: Sd Card Update
AUTOMATIC UPDATE The automatic update feature of HERA51 mobile POS is off by default, and you can change the setting by ADC (Android Deployment Configurator) to turn it on.
Page 123: Back Up Your Data
Basic Operation 3.7. BACK UP YOUR DATA With Backup, you can have your personal data (Apps & apps data, call history, contacts, and SMS) and certain system settings under your Google account backed up (over network connection) on the cloud. This allows you to easily restore the settings on this device after a Factory Reset (refer to Reset to Factory Default To start:...
Page 124 HERA51 Mobile POS To restore the backed up personal data of a Google Account, just add that account to the device Note: To back up your photos and videos, tap App Drawer (All Apps) Photos and log in your Google account to sync the files on your device with Google Photo Library.
Page 125: Reset To Factory Default
When setting your HERA51 Mobile POS by ADC (Android Deployment Configurator), the settings will automatically backup to “enterprise partition” of your HERA51 Mobile POS, and the settings saved in enterprise partition will not be erased by proceeding “Erase all data (factory reset)”. To erase all the settings, please select “Erase all data (factory reset with...
Page 126 HERA51 Mobile POS Confirm the action by tapping on the buttons and input the verification code (Please contact with support@cipherlab.com.tw to obtain your verification code). Finally, tap OK to perform a factory reset.
Page 127: Erase All Data (Factory Reset With Enterprise)
(factory reset with enterprise) Confirm the action by tapping on the buttons and input the verification code (Please contact with support@cipherlab.com.tw to obtain your verification code), and tap OK to perform a factory reset Please note that “Erase all data (factory reset with enterprise)” will erase all the data including...
Page 128: Welcome Wizard
HERA51 Mobile POS 3.8.3. WELCOME WIZARD As the mobile POS boots up for the first time after the reset, the Welcome wizard will run you through setting up the environment as well as restoring apps and data. During setup, you can tap “SKIP”...
Page 129 Basic Operation Step 3 Step 4 Insert your SIM to connect to Select a Wi-Fi network to log in or tap on “SKIP” to the next step. mobile network, or tap on If logged in a Wi-Fi network, you will be further asked to sign in your “SKIP”...
Page 130 HERA51 Mobile POS Step 7 Step 8 Choose Google services that you want to be It takes few seconds to complete. enabled, and tap “ACCEPT” to proceed. Once the initial setup is completed, the Home app screen shows up. Apps and settings will be...
Page 131: Wireless Radios
Wireless Radios Chapter 4 WIRELESS RADIOS With the Wi-Fi module integrated on the mobile POS, you can configure and connect to network wirelessly. IN THIS CHAPTER 4.1 Use Wireless Wide Area Network ..........132 4.2 Use Wireless Local Area Network (Wi-Fi) ........144 4.3 Use Bluetooth ................
Page 132: Use Wireless Wide Area Network
HERA51 Mobile POS 4.1. USE WIRELESS WIDE AREA NETWORK The mobile POS will be automatically configured to connect to your wireless service provider’s network when you insert a SIM card and turn on data connection for the first time. EDIT ACCESS POINT NAME You may need to change the access point name according to the information obtained from your mobile carrier.
Page 133: Share Wwan Data
Wireless Radios 4.1.1. SHARE WWAN DATA The WWAN connection on the mobile POS can be shared to other devices. You may share internet connection with a computer or device through USB or Bluetooth tethering, or share with a maximum of eight devices by turning the mobile POS into a Wi-Fi hotspot. BLUETOOTH TETHERING To share data connection through Bluetooth tethering: 1) Pair the mobile POS with the device of interest...
Page 134 HERA51 Mobile POS USB TETHERING To share data connection through USB tethering: 1) Connect the mobile POS with PC by the supplied snap-on cable 2) Go to App Drawer (All Apps) | Settings | Network & Internet | Hotspot &...
Page 135 Wireless Radios WI-FI HOTSPOT To share data connection in the form of a Wi-Fi hotspot: 1) Go to App Drawer (All Apps) | Settings | Network & Internet | Hotspot & tethering 2) Tap the Wi-Fi hotspot switch to enable data sharing through Wi-Fi.
Page 136 HERA51 Mobile POS DATA USAGE Data usage is the amount of data uploaded or downloaded on the mobile POS. Managing the data usage amount within a certain period of time is a recommended task, as an excess amount of data usage might incur additional fees from your service provider.
Page 137 Wireless Radios SET DATA USAGE LIMIT To set the data usage limit, please: 1) Go to App Drawer (All Apps) | Settings | Network & Internet | Data usage . On the Data usage page, scroll to “Mobile” and tap “Billing cycle”. Or tap “Mobile data usage”...
Page 138 HERA51 Mobile POS 2) Enable Set mobile data limit. 3) Tap “Data limit”, and input your required limit in “Set data usage limit” window, and tap “SET”. If a limit is set, when the data usage amount reaches the limit, mobile data connection will be...
Page 139 Wireless Radios ENABLE DATA USAGE DURING ROAMING 1) Go to App Drawer (All Apps) Settings Network & Internet | Mobile Network Or go to App Drawer (All Apps) | Settings | Network & Internet | Data usage , and on the action bar and then “Mobile network”. on the Data usage page, tap More...
Page 140 HERA51 Mobile POS 2) Enable “Roaming”, and a dialog box appears confirming whether you would like to enable data roaming. Tap OK to confirm RESTRICT BACKGROUND DATA 1) Go to App Drawer (All Apps) | Settings | Network & Internet | Data usage 2) Tap “Data saver”...
Page 141 Wireless Radios Once “Data saver” is on, an status icon will be shown in the status bar as well as in the Quick Setting menu: Note: The Mobile POS conserves data usage by restricting background mobile data. Certain applications and services will be disabled unless the mobile POS is connected to a Wi-Fi network.
Page 142: Data Connection Settings
HERA51 Mobile POS 4.1.2. DATA CONNECTION SETTINGS TURN ON/OFF DATA CONNECTION To manually turn on/off mobile data connection: 1) Go to App Drawer (All Apps) | Settings | Network & Internet | Data usage 2) Scroll to “Mobile” and tap on “Mobile data” to switch it on/off.
Page 143: Sim Card Settings
Wireless Radios 4.1.3. SIM CARD SETTINGS LOCK SIM CARD To lock the SIM card: 1) Go to App Drawer (All Apps) | Settings | Security & Location 2) Scroll down and tap on “SIM card lock” 3) Tap “Lock SIM card” to switch it on 4) Enter the PIN to enable SIM card lock.
Page 144: Use Wireless Local Area Network (Wi-Fi)
HERA51 Mobile POS 4.2. USE WIRELESS LOCAL AREA NETWORK (WI-FI) 4.2.1. CONNECT TO WI-FI NETWORK To power on Wi-Fi: 1) Swipe down from the top of the screen to open Quick Settings Menu 2) Tap Wi-Fi  to scan for available networks. Select a network to connect...
Page 145 Wireless Radios Select a network to connect. If the network is an open one, the mobile POS will attempt to connect to it directly. When connected, the status will change to show “Connected”. If the network is a secured one, the mobile POS prompts a dialog to enter the password for the connection...
Page 146: Manually Add Wi-Fi Network
HERA51 Mobile POS 4.2.2. MANUALLY ADD WI-FI NETWORK If the network you would like to connect to does not broadcast its SSID, or if the network is out of range, you may add it manually. 1) Go to App Drawer (All Apps) | Settings | Network &...
Page 147 Wireless Radios Note: Certificates may be installed under: App Drawer (All Apps) | Settings | Network & Internet | Wi-Fi | Wi-Fi preferences | Advanced | Install certificates. The mobile POS supports the following certificate file extensions: File Extension Type Standard Certificate Key Stored Description...
Page 148: Wi-Fi Preferences
HERA51 Mobile POS 4.2.3. WI-FI PREFERENCES Wi-Fi Preferences is devided into 2 parts: “Cipherlab Proprietary Setting” and “Advanced”. To access advanced Wi-Fi settings: 1) Go to App Drawer (All Apps) Settings | Network & Internet | Wi-Fi 2) Scroll down to the bottom of the “Wi-Fi...
Page 149 Wireless Radios The available settings are as below: Item Description Open network notification Notify when an open network is available. Installs certificates recently downloaded or Install certificates placed on the internal storage. The selected network scorers will label the the Network rating provider quality of the open Wi-Fi networks you are connecting to between very fast and slow.
Page 150 Select the Wi-Fi channel(s) to narrow down Channel Selection frequency band of the 2.4GHz (802.11b/g/n) or 5 GHz (802.11a/n). Enable TCPDUMP Logger Retrieve TCP packet log. Restore all the settings in “Cipherlab Reset to Default Propruetary” to default.
Page 151 Wireless Radios To configure “Enable Fast Transition”, “Enable WLAN Blacklist”, “Wi-Fi Connection Timeout”, “Captive Portal Detection”, and “Channel Selection”, Wi-Fi must be turned off. Turn on Wi-Fi again to apply the setting(s) once the configuration is done.
Page 152: Configure Proxy Server
HERA51 Mobile POS 4.2.4. CONFIGURE PROXY SERVER A proxy server acts as an intermediary between an endpoint device and another server from which the device is requesting a service. To change the proxy settings for a connection: 1) Long press on a network in the available Wi-Fi hotspot list, and then tap on “Modify network”...
Page 153: Connect With Wi-Fi Protected Setup (Wps)
Wireless Radios 4.2.6. CONNECT WITH WI-FI PROTECTED SETUP (WPS) Wi-Fi Protected Setup (WPS) allows easy establishment of a secure wireless network. The mobile POS supports WPS Push Button configuration. Go to App Drawer (All Apps) | Settings | Network & Internet | Wi-Fi | Wi-Fi preferences...
Page 154: Modify Wi-Fi Network
HERA51 Mobile POS 4.2.7. MODIFY WI-FI NETWORK To change the settings for a connected network: 1) Tap and hold a connected network in the Wi-Fi hotspot list 2) Tap Modify network in the pop-up menu 3) In the dialog box that opens, modify the network settings, and tap Save 4.2.8.
Page 155: Use Bluetooth
Wireless Radios 4.3. USE BLUETOOTH You can configure Bluetooth settings and manage Bluetooth services provided on remote devices. 4.3.1. BLUETOOTH PROFILES Bluetooth Profiles Supported Generic Access Profile (GAP) For device discovery and authentication. Service Discovery Access Profile (SDAP) Discovers services on remote devices. Headset Profile (HSP) Describes how a Bluetooth enabled headset should...
Page 156: Turn On Bluetooth
HERA51 Mobile POS 4.3.2. TURN ON BLUETOOTH By default, Bluetooth is turned off, to turn it on:  Via Quick Settings Panel 1) Swipe down from the top of the screen to open Quick Settings Panel. Tap on Bluetooth icon to turn it on or off.
Page 157 Wireless Radios  Via Settings page 1) Go to App Drawer (All Apps) | Settings | Connected devices | Bluetooth 2) Tap the switch to turn on this function while enabling the Bluetooth visibility of this device simply switch Bluetooth on/off in App Drawer (All Apps) | Settings | Connected...
Page 158: Change Bluetooth Name
HERA51 Mobile POS 4.3.3. CHANGE BLUETOOTH NAME To change the Bluetooth name of this Mobile POS: 1) Go to App Drawer (All Apps) | Settings | Connected devices | Bluetooth 2) Turn Bluetooth on and tap on “Device name” 3) On the pop-up dialog “Rename this device”, type a new name in the field and tap RENAME...
Page 159: Pair Bluetooth Devices
Wireless Radios 4.3.4. PAIR BLUETOOTH DEVICES 1) Go to App Drawer (All Apps) | Settings | Connected devices | Bluetooth 2) Switch Bluetooth to On and tap “Pair new device” to scan for available Bluetooth devices nearby. Scroll through the list and tap the device you would like to pair 3) The Bluetooth pairing request window opens.
Page 160: Unpair Bluetooth Device
HERA51 Mobile POS 4.3.5. UNPAIR BLUETOOTH DEVICE To unpair a paired device: 1) In the Paired Devices list, tap the settings button next to the paired device. 2) On the Paired device screen, tap FORGET.
Page 161: Use Near Field Communications
Wireless Radios 4.4. USE NEAR FIELD COMMUNICATIONS Near field communications (NFC) uses close proximity (4 cm or less) to establish radio communication through electromagnetic fields. With NFC enabled, the mobile POS can collect information from NFC tags, exchange information with other NFC supported devices, and even change information on the NFC tag if authorized.
Page 162: Pair With Nfc Enabled Bluetooth Devices
HERA51 Mobile POS 4.4.1. PAIR WITH NFC ENABLED BLUETOOTH DEVICES 1) On the device you would like to pair with, make sure NFC is enabled and Bluetooth discovery is enabled. 2) Hold the mobile POS without covering the antenna area at the lower end of the battery.
Page 163: Using The Phone
Chapter 5 USING THE PHONE The HERA51 Mobile POS allows making phone calls and connecting to the network over Wideband Code Division Multiple Access (WCDMA). Insert the SIM card before turning on the power. Refer to Installing SIM Card, SAM Card and Memory Card.
Page 164: Sim Card Management
HERA51 Mobile POS 5.1. SIM CARD MANAGEMENT The default setting for celluar networks is “Automatically select network”. To manually select the cellular network, please Go to App Drawer (All Apps) | Settings | Network & Internet | Mobile Network 1) Disable “Automatically select network”, and tap on “Network”. Available networks will be...
Page 165 Using the PHONE EMERGENCY CALLS Depending on your service provider, the mobile POS might support making emergency phone call when the SIM card is locked, or even when no SIM card is inserted. Emergency phone numbers will vary by country.
Page 166: Phone Application
HERA51 Mobile POS 5.2. PHONE APPLICATION 5.2.1. PHONE INTERFACE When a SIM card is installed on the mobile POS, a signal icon appears on the status bar. The filled part of the signal icon indicates the strength of the connection.
Page 167 Using the PHONE tab page, it displays your favorite contacts & your frequent calls: frequent calls favorite contacts To add a favorite contact, please tap the contact in tab page and tap the star mark to add. and select “Clear frequents”. To clear the frequent calls, please tap...
Page 168: Place Call
HERA51 Mobile POS 5.2.2. PLACE CALL to expand the dial pad, and enter the phone number in the dial pad and tap initiate the call. If you need to frequently make calls to an interactive voice system, you may tap...
Page 169: During A Call
Using the PHONE 5.2.3. DURING A CALL When a call is connected, the phone keypad features the following buttons: Button Description Mute: Mutes the call. Keypad: Opens the keypad. Speaker: Turns on the speaker. Add call: Adds another person to the call. Hold: Places the call on hold.
Page 170 HERA51 Mobile POS PLACE CALL USING CONTACTS To make a call using contacts: 1) In the phone application page, tap 2) Tap a contact to initiate a call.
Page 171: Receive Incoming Call
Using the PHONE 5.2.4. RECEIVE INCOMING CALL When a call is incoming on the mobile POS, tap to pick it up. Incoming calls will be logged in the Phone application; in the case of a missed call, a notification will be displayed. See Check Miss Calls To mute the ringtone of an incoming call, press the volume down button 5.2.5.
Page 172: Call History
HERA51 Mobile POS 5.2.6. CALL HISTORY 1) On the Phone application page, tap the History button to open a list of history calls. Or you can tap the settings button and then Call History. Button Description Connected calls. Missed calls.
Page 173: Call Settings
Using the PHONE 5.2.7. CALL SETTINGS and select “Settings” to enter the settings page: Tap each setting for more setting options.
Page 174: Make Multi-Party Calls
HERA51 Mobile POS 5.2.8. MAKE MULTI-PARTY CALLS To make multi-party conference calls: 1) On the Phone application page, enter the first number to call and tap to initiate the call. After the call has begun, tap and then Add call to add another member. The first call will be put on hold.
Page 175: Audio Modes
Using the PHONE 5.3. AUDIO MODES The mobile POS offers three different audio modes for phone calls: HANDSET MODE This is the default audio mode which uses the receiver above the touchscreen for audio output during calls. SPEAKER MODE This mode uses the built-in speaker for audio output during calls. HEADSET MODE Connect a Bluetooth headset the mobile POS for audio output during calls.
Page 176: In-Call Volume
HERA51 Mobile POS 5.4. IN-CALL VOLUME Use the volume buttons to adjust the ringer volume and system sound level. When in the middle of a call, use the volume buttons to adjust in-call conversation volume.
Page 177: Specifications
Specifications SPECIFICATIONS PLATFORM, PROCESSOR & MEMORY Operating System & CPU OS Version Android 8.1 Oreo with GMS Certified Qcta-core 1.8GHz Memory 16GB (64GB by request) 2GB (4GB by request) Expansion Slot One Micro SD card slot (up to 32GB for SDHC; up to 64GB for SDXC)
Page 178: Communication & Data Capture
HERA51 Mobile POS COMMUNICATION & DATA CAPTURE Communication USB Client USB 2.0 OTG WPAN Bluetooth Class II, v4.1 and v2.1+EDR (2402~2480 MHz: 3.3dBm) WLAN 802.11 b/g/n and 802.11 a/ac/n networking (2412~2472 MHz: 18.34dBm 5180~5240MHz: 21.06dBm, 5260~5320MHz: 21.46dBm, 5500~5700MHz: 21.90dBm, 5745~5825MHz: 14.30dBm (USA only) ) Operations in the 5.15-5.35GHz band are retricted to indoor usage only.
Page 179 Specifications Data & Image Capture Digital Camera Autofocus 13 megapixels with user-controllable LED flash Barcode Reader 2D Imager HF RFID Reader HF RFID 13.56 MHz (-18.18 dBuA/m at 10m) frequency which supports ISO14443A, ISO14443B, ISO15693, Felica Supports NFC (Peer-to-Peer, Card Reader, Card Emulation)
Page 180: Electrical Characteristics
HERA51 Mobile POS ELECTRICAL CHARACTERISTICS Batteries Main Battery Pack Replaceable and rechargeable 3.8V 4000mAh/3.75V 5300mAh Li-ion battery, full charging 4.35V 4 hours @25 (4000mAh) Minimum charging time: 6 hours @25 (5300mAh) For the first time charging the main battery, please charge it for at least 8 to 12 hours.
Page 181: Physical Characteristics
Specifications PHYSICAL CHARACTERISTICS Color Touch Screen Display Display 4.7” LCD, Corning Gorilla Glass 3, touch supports bare/wet/gloved finger and stylus inputs Resolution HD (720x 1280 pixels) Notifications Status LED A Ttri-color (white, green, & red) LED indicators signaling charging and data capturing status Audio Integrated with one speaker playing sounds for events Vibrator...
Page 182: Environmental Characteristics
Multiple drops onto concrete at 1.2 m (3.9 ft.) on all six sides Multiple drops onto concrete at 1.5 m (4.9 ft.) on all six sides for HERA51 Mobile POS with rubber boot Electrostatic Discharge ±12 kV air discharge, ±8 kV contact discharge...
Page 183: Programming Support
Specifications PROGRAMMING SUPPORT Development Environment & Tools JAVA Environment Android studio Software Development Kit: JAR Environment: Visual Studio Software Development Kit: DLL (Xamarin Library) Software & Utilities Software Package Reader Config Software Trigger Mobile Deployment Suite for Android App Lock Xamarin Binding HF RFID Configuration Signature Capture...
Page 184: Open Source License
HERA51 Mobile POS APPENDIX I OPEN SOURCE LICENSE The Reader Config involves the Android-serialport-api project of Apache License Version 2.0, January 2004. http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
Page 185 Appendix I "Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below). "Derivative Works"...
Page 186 HERA51 Mobile POS 4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions: a. You must give any other recipients of the Work or Derivative Works a copy of this License;...
Page 187 Appendix I 7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.

CipherLab HERA51 Reference Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for CipherLab HERA51

Summary of Contents for CipherLab HERA51

Table of Contents