Subscribe to Our Youtube Channel
Related Manuals for EHRET Voletronic io
Summary of Contents for EHRET Voletronic io
- Page 1 Voletronic io Motorisation for window shutters installation and operating instructions installation specialist personnel Valid from 03.2021 E 641.4...
-
Page 2: Notes
Voletronic io window shutter therefore always to be retained until the prod- drive. insufficient knowledge at the time of uct is disposed of. -
Page 3: Table Of Contents
Contents notes ..........2 explanation of signs and symbols . -
Page 4: Explanation Of Signs And Symbols
important notes Explanation of signs and symbols Safety notes Warning notes Only qualified specialist personnel may carry out installation and commission- ing! DaNgEr WarNINg Designates an immediately pending dan- ger that could lead to death or severe in- Incorrect installation could lead to se- juries if the respective precautionary vere injuries and/or damage to prop-... - Page 5 Make sure that the shutters are locked be- be observed, as otherwise damage to the fore any wind load occurs. motor could occur. eHret GmbH assumes the shutters may not be operated at wind no liability for damage resulting from incor- speeds from 62 km/h (stormy wind).
-
Page 6: Ec Declaration Of Conformity
GmbH aluminium shutters Bahnhofstrasse 14 - 18 D - 77972 Mahlberg declares that the product: EHrEt window shutter drive VOLEtrONIC io to which this guideline refers, is in conformance with the stipulations of Machinery Directive 2006/42/EC 2014/53/EC radio equipment / r&tte... -
Page 7: Installation Faqs
(e.g. VDe 0100). How is the VOLEtrONIC io window shutter • I t is recommended that no more than five drive mounted? drives are secured simultaneously by a single line safety switch. -
Page 8: Disposal
important notes Disposal Important Important Disposal Disposal • T he following information must be strictly Dispose of all machine parts in accordance adhered to in order to prevent any environ- with the applicable legal conditions in or- mental damage. even if the machine is dis- der to prevent the possibility of any harm posed of by certified experts, the operator to human health or the environment. -
Page 9: Product Description
(situo io pure ii) or Handheld transmitter Nominal torque 4 nm per motor, nina io (bidirectional touch display control). peak torque 50 nm • T he Voletronic io folding shutter drives Speed 1,5 rpm. are checked and delivered fully charged. Power consumption max. -
Page 10: Scope Of Delivery
1 product description Scope of delivery VOLEtrONIC io accessories per sash Motorisation for window shutters 1× (1L/1R, 2L/2R); 2× (2, 3L/3R, 4) M3 × 6 mm Variante a Header installation Washer Ø10.5 mm A2 S2 Hexagon screw M10 × 20 cover cap, hexagon, WaF17 Guide rail Variant B carriage arm reveal installation (on the side) 2× Ø 4,8 1×... - Page 11 1 product description Coupling with multiple-section sashes tools required* 2l/2r, 3l/3r, 4 *not included in the scope of delivery Masonry drill Guide lug Drill Ø 4.2 mm Guide rod pivot bearing 2× rivets N1 Operation torx tX 20+25 6440 wall transmit- situo io pure ii 6643 nina io hand- ter smoove 1 o/c io hand-held transmit-...
-
Page 12: Installation Instructions
2 installation instructions 2 Installation instructions Preparation NOtES Before mounting the drive, make sure that each sash of the folding shutter can be moved freely over the entire swivel range. the folding shutter must not jam or rub against its immediate sur- roundings (frame, masonry, etc.). -
Page 13: Mounting The Installation Profile And Fastening The Drive Modules
2 installation instructions Mounting the installation profile and fastening the drive modules WARNING Danger of injury/property damage caused by unsuitable fastening materials select the fastening material in accordance with the load capacity of the installation sub- strates! NOtES • T he selection of the fastening method is de- pendent on the substrate and is therefore exclusively your own responsibility. - Page 14 2 installation instructions Variant a Header installation position the installation profile with shutters insert the electromechanical module into the closed (dimension X + 5 mm) and align it frame on the side where the power supply horizontally. enters. ...
- Page 15 2 installation instructions Variant B Reveal installation position the installation profile with lateral insert the electromechanical module into the fastening brackets (dimension X + 5 mm) and frame on the side where the power supply align it vertically and horizontally with a spirit enters.
- Page 16 2 installation instructions Variant C At the bottom above the windowsill position the installation profile with lateral insert the electromechanical module into the fastening brackets at the bottom above the frame on the side where the power supply windowsill (dimension X + 5 mm) and align enters.
-
Page 17: Cable Routing And Wiring
230 V 50 Hz switch on the voltage supply. the Voletronic io folding shutter drive con- firms by means of an audible signal. if this is not the case, check the electrical connection again. switch off the power supply again after... -
Page 18: Attaching The Cover
Half open Hold the cover parallel and clip it firmly in place. VOLETRONIC io attach adhesive buffers. b) at an angle of more than 90°outside the open end position. Angle of more than 90°... -
Page 19: Attaching Guide Rails To The Sash
2 installation instructions attaching guide rails to the sash thread the sash arm into the guide rail and NOtES plug the end pieces into the guide rail observe the edge clearance of the guide rails with rabbet or surface-mounted installation. sash arm For models with protruding slats, use the 6220 supports for end pieces of window shutter drive... -
Page 20: Commissioning
2 installation instructions COMMISSIONINg actIvate radIo wall transmItter NOtE CautION in order to carry out commissioning success- Do not press against the sensitive side of the fully, the following commissioning work steps wireless wall transmitter with the flat of the must be carried out consecutively and coher- hand because otherwise unintended com- ently. - Page 21 2 installation instructions check dIrectIon of rotatIon and self-learnIng process prIorIty of the sashes NOtES NOtES the leading sash is the sash with the cover the teach-in phase allows the configuration of strip. the drive according to its installation environ- ment.
- Page 22 2 installation instructions a1) user confirmation B) negative feedback from the drive the drive has detected an inappropriate setting if the steps of the self-learning process have during the self-learning process. run without errors (no obstacles or unexpect- ed stops): three beeps sound and the drive locks.
- Page 23 2 installation instructions connectIng the radIo wall verIfIcatIon of proper transmItter to the drIve functIonIng CautION Opening procedure Do not press against the sensitive side of the Briefly press the open button on the io- wireless wall transmitter with the flat of the radio transmitter.
-
Page 24: Cutting The Coupling Rod To Size And Mounting It
2 installation instructions Cutting the coupling rod to size and mounting it For multiple-section sashes (2L/2R, 3L/3R, 4) close the double shutter and mark the centre NOtES observe the edge clearance of the guide lug of rotation of guide lug B. afterwards, open with rabbet or surface-mounted installation! the double shutter and measure the distance from a to B. -
Page 25: Crimped Metal Ribbon
Hook the guide rod in the guide lug, slide the against shifting in place as follows after the pivot bearing on and lock in place with the installation of the Voletronic io window 3 locking set screws in the pivot bearing. shutter drive! -
Page 26: Operation
The sash opens and stops automatically, once position can be stored in the memory of the it reaches the stops. Voletronic io shutter drive. that position press the button. must not correspond to either the open or the The window shutter closes completely. -
Page 27: Detecting Obstacles And Freeze Protection
press the button. the automatic obstacle recognition protects The folding shutter moves into the preferred the Voletronic io against damage and pre- position. vents accidents. if a sash encounters an obstacle when opening or closing, the folding shutter is automatically stopped and moves in the opposite direction until it is fully opened or closed. -
Page 28: Activate The New Setting Mode
3 operation activate the new setting mode reverse sash priority NOtES NOtES Using an io radio transmitter, some parame- this step is required if the arrangement of the ters, such as sash priority, direction of rotation, sashes is reversed. closing force, buzzer function, can be adjusted the leading sash is the sash with the cover subsequently in the reset mode. -
Page 29: Setting The Closing Force
NOtES NOtES this step is necessary if the direction of rota- the Voletronic io drive is set ex works to tion of the drive does not correspond with the closing force level 2. pressed buttons on the io radio transmitter. -
Page 30: Buzzer Function
Buzzer function NOtES NOtES eHret recommends activating the buzzer returning to the pre-configured mode deletes function in order to signal shutter movements the changes to the leaf priority, the direction of rotation, the closing force setting, all radio (e.g. -
Page 31: Radio Transmitter "Io Pure
“io Pure” Option switch on the power supply again. NOtES as an option, the Voletronic io folding the sash with cover strip performs an open/ shutter drive can also be controlled by means close movement. of a io pure wireless hand-held transmitter. -
Page 32: Maintenance
Danger of explosion when using incorrect battery types in the event of using a battery not recommend- ed by eHret, the liability and warranty obliga- tions of eHret do not apply. only use the battery recommended by eHret, part no. 6406 Emergency battery (op- tional), 9.6 V / 1600 mAh. - Page 33 4 Maintenance insert the battery by placing it in the 5 fas- tening hooks provided on the circuit board housing. Make sure that the battery is firmly fitted in place. connect the battery to the circuit board.
-
Page 34: Restore Factory Settings
• A ll these parameters of the drive are reset to must be used. the values set by ehret in the delivery state. to restore the initial configuration, press and open the sashes halfway. hold the -key on the keypad of the drive for 15 sec. -
Page 35: Operator Interface Of The Drive
4 Maintenance Operator interface of the drive When the parameter code flashes on the NOtES keypad display, press the or keys Keypad and display select the parameter. • T he keypad on the drive module allows you to set a number of adjustment parameters for the drive. -
Page 36: List Of Setting Parameters
4 Maintenance List of setting parameters Parameter Display Description Parameter Display Values allows the direction of rotation of the drive to be changed. standard direction changing the direction When changing this parameter, a of rotation of the drive. self-learning process of the end opposite direction positions must be started. - Page 37 4 Maintenance Parameter Display Description Parameter Display Values there is no back-up battery on the product. With / Without battery the backup battery has been detected. Battery not present or damaged or charge level insufficient for drive operation. emergency battery Battery charge low.
-
Page 38: Troubleshooting
4 Maintenance troubleshooting problem possible causes solutions the drive emits audible if the emergency battery is installed, the Make sure that the product is connected signals when moving. audible signals indicate an interruption in the to the power supply. power supply. -
Page 39: Error Codes On The User Interface Of The Drive
4 Maintenance problem possible causes solutions the drive emits an audible the free movement of the folding shutter is Make sure that the folding shutter can signal and stops in a middle obstructed (obstacle, jammed, movement of move freely. position. - Page 40 Fax + 49 (0) 78 22 /439 - 116 www.ehret.com © 02.2022 eHret GmbH | e 641.4 | Diese technische Unterlage enthält urheberrechtlich geschützte informationen. alle rechte sind vor behalten. Änderungen in dieser Unterlage sowie technische Änderungen behalten wir uns vor. Diese Unterlage wurde mit beson- derer sorgfalt erstellt.
Need help?
Do you have a question about the Voletronic io and is the answer not in the manual?
Questions and answers