Using External Components; Connecting The Video Signal Cables; Connecting The Ieee1394 Cable; Composite And Component Connections - JVC GY-HD110U Instructions Manual

USING EXTERNAL COMPONENTS

Connecting the Video Signal Cables

Clamp filter IEEE1394 switch
IEEE 1394
HDV
DV
Wind once
Composite cable
IEEE 1394
HDV
DV
Component cable
C H A N G E 1 3 9 4 S W I T C H
Displaying Alarms
• CHANGE 1394 SWITCH
Displayed when the setting for the input/output video format
from the IEEE1394 connector and the setting for the
IEEE1394 switch are different.
Set the IEEE1394 switch so it matches the video format.
56

Connecting the IEEE1394 Cable

To reduce the emission of unwanted radio waves, be sure to
attach the provided clamp filter as shown in the figure on the left.
• Attach the clamp filter as close to the camcorder as possi-
ble, as shown in the figure.
• Set the IEEE1394 switch on the left panel of the cam-
corder.
DV : DV format
HDV : HDV format
CAUTION
When connecting the IEEE1394 cable from/to Camcorder,
VCR and other IEEE1394 device, make sure the following
instructions, otherwise the IEEE1394 circuit device may be
destroyed.
• Turn the power of both devices OFF and connect the
IEEE1394 cable.
• Do not insert incorrectly (in reverse) the IEEE1394 cable
end to IEEE1394 port of both devices.
• Do not connect the IEEE1394 cable under the condition
of static electricity.
• Turn the power of both devices OFF when changing the
IEEE1394 switch from/to HDV/DV.

Composite and Component Connections

The video signals output from the video signal output connec-
tors on this camcorder (VIDEO/Y, P , P ) are as described
B R
below, depending on the settings for the OUTPUT TERMI-
NAL item on the VIDEO FORMAT menu screen.
AUTO : Automatically switches to a composite or
component signal, depending on which
cable is connected to the video signal
output terminal and outputs the signal.
COMPOSITE : Outputs a composite signal regardless of
which cable is connected to the video sig-
nal output connector.
COMPONENT : Outputs a component signal regardless
of which cable is connected to the video
signal output connector.
Output signal when AUTO is set
Connector (G: Unconnected F: Connected) Output
Signal
VIDEO/Y P P
B R
F F F
COMPONENT
F G F
COMPOSITE
F F G
COMPONENT
F G G COMPOSITE
None of the above OFF
In addition, you can use the PB TAPE item to set whether to
automatically detect the video format of the playback tape or
only play back a particular format when playing back a tape.
X See page 65.
CAUTION
• Be careful not to apply excess force to the video signal
output terminal when connecting or disconnecting the
cable. This will cause poor contact or failure.
• To use the automatic signal-switching function while the
RCA-BNC conversion connector is in use, unplug the
entire connector from the video output terminal.

Dubbing with AV Devices

1.
Composite cable
or
Component cable
IEEE 1394
Signal flow
HDV
DV
Recording unit
LINE
OUTPUT
connector
Signal flow
1.
Audio cable
Clamp filter
4.
VIDEO FORMAT menu screen
5.
AUDIO menu screen
USING EXTERNAL COMPONENTS
By connecting the video signal output terminal and the LINE
OUTPUT terminal on this camcorder to an AV device, analog
signal dubbing is possible.
1.
Connect the cables.
Use the provided cable for the audio cable.
To reduce the emission of unwanted radio waves, be sure
to attach the provided clamp filter as shown in the figure
on the left.
• Attach the clamp filter as close to the camcorder as
possible, as shown in the figure.
2.
Turn both devices on.
3.
Set the camcorder to VTR mode.
Press the CAM/VTR button. The VTR indicator lights.
4.
Set the video output.
Set the VIDEO FORMAT menu screen. X See page 64.
• HDV PB OUTPUT item:
Set the video format to be output from the video output
terminal during tape playback.
• PB TAPE item:
Select whether to automatically detect the playback tape
video format or play back only a particular format.
Normally, use the "AUTO" setting.
• OUTPUT TERMINAL item:
Set either component or composite output.
Normally, use the "AUTO" setting.
5.
Set the audio output. X See page 55.
Set the AUDIO/MIC menu screen. X See page 72.
• AUDIO MONITOR item:
Set stereo audio or mixed audio.
• PB AUDIO CH [DV] item:
Set the audio channel to be output.
• Set the MONITOR SELECT switch.
6.
Insert the videocassettes.
GY-HD110 : Insert the recorded videocassette.
Recording unit : Insert the videocassette to be
dubbed to.
7.
Press the PLAY/STILL button on the GY-HD110 to start
playback.
8.
Start recording on the recording unit.
For details, see the instructions to the unit used for
recording.
9.
When dubbing is completed.
Stop recording on the recording unit, and then press the
STOP button on the GY-HD110 to stop playback.
57