Audio Input Signal Selection; Selecting The Ch-2 Channel Input Connector; Selecting The Audio Signal Input; Adjusting Audio During Recording - JVC GY-HD110U Instructions Manual

SETTING AND ADJUSTMENTS BEFORE SHOOTING

Audio Input Signal Selection

CH-2 INPUT switch
AUDIO INPUT
switch
Monitor
speaker
MONITOR SELECT FULL AUTO switch
switch
MONITOR
volume
CH-1/CH-2
CH-1 audio input
AUDIO SELECT switch
level volume
CH-2 audio input level
volume
STATUS 1 screen
Audio level
Indicator level (reference)
48
The GY-HD110 is provided with the INPUT1 connector and
the INPUT2 connector for audio input.
Select the audio from the INPUT1 connector or the INPUT2
connector using the CH-2 INPUT switch for the audio to be
recorded in CH-2.
Selecting the CH-2 channel input con-
nector
Select using the CH-2 INPUT switch.
INPUT1 : Inputs the audio from the INPUT1 connector
into CH-2.
INPUT2 : Inputs the audio from the INPUT2 connector
into CH-2.
MEMO
The audio from the INPUT1 connector is also input into CH-
1 regardless of the setting.

Selecting the audio signal input

Select the sound to be input to the INPUT1 or INPUT2 con-
nector using the AUDIO INPUT switch.
The setting is made for each of INPUT1 or INPUT2 connec-
tor.
LINE : Set to this position when connected to audio
equipment, etc.
The reference input level is +4 dBs.
MIC : Set to this position when using a dynamic micro-
phone.
MIC+48V : Set to this position when a microphone (phan-
tom microphone) requiring +48 V DC power sup-
ply is connected.
CAUTION
When connecting a component that does not require +48 V
power supply, make sure that the switch is not set to
MIC+48V before the component is connected.
MEMO
You can select the normal input level for MIC and MIC+48V
in the INPUT1, 2 MIC REF. item on the AUDIO/MIC [1/2]
menu screen.

Adjusting Audio during Recording

For each audio channel, use the CH-1/CH-2 AUDIO SELECT
switch to select whether the audio level adjustment should be
set to AUTO mode or MANUAL mode.
Adjusting the audio input level control
The audio input level can be adjusted manually when the GY-
HD110 is in the record, record-standby or stop mode.
1.
Set the CH-1/CH-2 AUDIO SELECT switch of the channel
whose audio level that you want to adjust manually to
MANUAL.
2.
Rotate the audio input level control corresponding to the
audio input level to be adjusted.
• Adjust so that the peak level does not exceed the –3 dB
point when a loud sound is input.
SETTING AND ADJUSTMENTS BEFORE SHOOTING
CAUTION
• When the AUDIO INPUT switch is set to MIC, be sure to
check that the microphone is connected to the INPUT1/2
connector. If the microphone is not connected, increasing
the audio level could cause noise from the input connec-
tor to be recorded on the tape. When the microphone is
not connected to the INPUT1/2 connector, set the AUDIO
INPUT switch to "LINE" or turn down the audio level con-
trol.
• In the FULL AUTO mode, the audio level volume cannot
be adjusted with the audio level controls on the CH-1 and
CH-2.
MEMO
The reference level for audio recorded on the tape can be
set with the AUDIO REF. LEVEL item on the AUDIO/MIC
menu screen. (–20 dB or –12 dB) The level will change for
both CH-1 and CH-2.

Monitoring Audio during Recording

The audio input during recording, in record-pause or stop
mode can be monitored through the monitoring speaker or
earphone.
• Select the audio channel to be monitored using the MONI-
TOR SELECT switch.
CH-1
BOTH
CH-2
• The MONITOR volume control adjusts the monitoring vol-
ume.
• The loudspeaker or earphone outputs an alarm tone in the
case of an abnormal condition occurring in the unit.
An alarm tone is also output when the tape end is reached
or when the battery is running down.
* Do not increase the audio monitoring volume exces-
sively; otherwise howling with the camera microphone
may occur.
MEMO
PHONES jack
• When connecting a stereotype earphone, make the fol-
lowing settings to output stereo sound.
1Set the MONITOR SELECT switch to BOTH.
2Set the AUDIO MONITOR item on the AUDIO/MIC [2/2]
menu screen to STEREO.
• When AUDIO MONITOR item on the AUDIO/MIC [2/2]
menu screen is set to "STEREO", only the audio of CH-1
is output from the monitoring speaker.
• The volume of the alarm tone is set with the ALARM VR
LEVEL item on the OTHERS [1/2] menu screen. (OFF/
LOW/MIDDLE/HIGH)
: The sound input to the CH-1 channel is output.
: The sound input to the CH-1 and CH-2 channels
is output mixed.
: The sound input to the CH-2 channel is output.
49