Advertisement
Quick Links
AS-1100 Compact Smart Fuse Box
NOTE: Do not install and/or operate this product unless you have read and understand all the safety information and instructions contained in this
manual.
IMPORTANT!
This manual provides all the necessary information for your product to be properly and safely installed.
Please read all instructions before installation, and make sure you follow them carefully during the instal-
lation process. Failure to follow these instructions may result in DAMAGE to the product or vehicle,
and/or SERIOUS INJURY to you and your passengers!
Product Code
Approval
Working Temperature
Input Voltage
Input I/O
Output Voltage
Output I/O
Dimension
DIAGRAM
Ground
Default Button
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
Pl ea s e s ee " Re-Map
for TRI.+ / TRI.-"
Installation Manual:
AS-1100
R10
-30°C~+70°C
12-24 VDC
Panel x2
Power x1
same as input voltage
10 amp at 12VDC / 5 amp at 24VDC x3
10 amp at 12VDC / 5 amp at 24VDC (Shared) x 3
0.2 amp x5
Positive / Negative Common Trigger at 0.2 amp (2 slot) x1
ID-11RS (Controller): 100mm x 60mm x 18.5mm
FS-14P (Fuse Box): 148mm x 92mm x 25mm
AS-1100
25A
Fuse
Amp
I/O
10A
SW1
10A
SW2
10A
SW3
SW4
10A Combi ned
SW5
SW6
0.2A
SW7
0.2A
SW8
0.2A
SW9
0.2A
SW10
0.2A
SW11
0.2A
TRI.+
Nega ti ve
TRI.-
L1 - L10
Vehicle
Ignition
Second Control Panel
- 1 -
AS-1100-RB
Advertisement
Related Manuals for Abrams AS-1100
Summary of Contents for Abrams AS-1100
- Page 1 Installation Manual: AS-1100 Compact Smart Fuse Box NOTE: Do not install and/or operate this product unless you have read and understand all the safety information and instructions contained in this manual. IMPORTANT! This manual provides all the necessary information for your product to be properly and safely installed.
-
Page 2: Reset To Default
Reset to Default - Press C1 and C11 together for 10 seconds to reset all configuration to default factory setting. The Red LED backlights on all the buttons will flash 5 times to indicate the device has been reset. Momentary Switch Programming Function To set button as momentary switch - Push C1 and C2 together for 5 seconds to ender Momentary Switch Programming... - Page 3 Reverse EU Siren Interlock Function Programming To interlock buttons between primary and secondary button. - the secondary button will now activate when primary button is enabled. Function - the primary button will be disabled when secondary button is disabled. - the user may still disable the primary button on its own command. - Push C1 and C4 together for 5 seconds to enter Siren Interlock Programming mode.
- Page 4 Input Command for I/O SW11 To enable the accessibility or activation of certain button base on the receival of input signal from I/O SW11 Push C1 and C6 together for 5 seconds to enter the programming mode. LED L5 and L6 will be solid to indicate you are in the programming mode.
- Page 5 To sync configuration from one controller to another - After you had finalized the configuration on your controller, you may sync your configuration to another controller via ”AS-1100-RB" or "ID-CEM" device to shorten the setup time. - Connect the configurated handheld controller (Master) to and a non-configurated handheld controller (Slave) via "AS-1100-RB"...
-
Page 6: Led Indicators
***Advance Feature***: Output Connection Re-map Function To re-map the position of the I/O to the buttons - Press C5 and C6 together for 5 seconds to enter I/O Connection Re-map Programming mode for connecting: SW1-SW11 and TRI+/-. LED L2, L4, L7 and L9 will be solid to indicate you are now in the programming mode for Output Connection Re-map.