Related Manuals for Advantech VEGA-1100
Summary of Contents for Advantech VEGA-1100
- Page 1 User Manual VEGA-1100 HDMI 2.0 Over IP Multi-cast Transceiver System with Bi- directional IR, RS-232, Audio Extender/Extractor, USB 2.0, & Video Wall Support...
- Page 2 No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
- Page 3 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
- Page 4 Document Feedback To assist us with improving this manual, we welcome all comments and constructive criticism. Please send all such feedback in writing to support@advantech.com. Packing List Before system installation, check that the items listed below are included and in good condition.
- Page 5 In accordance with the IEC 704-1:1982 specifications, the sound pressure level at the operator’s position does not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to IEC 704-1 standards. Advantech disclaims all responsibility for the accuracy of any statements contained herein. VEGA-1100 User Manual...
- Page 6 Do not touch any components on the CPU card or other cards while the PC is powered on. Disconnect the power before making any configuration changes. A sudden rush of power after connecting a jumper or installing a card may damage sensitive electronic components. VEGA-1100 User Manual...
-
Page 7: Table Of Contents
HDMI Pin Definition................. 11 Figure 3.1 Type A (Receptacle) HDMI........11 Chapter Operation Approach ......13 Software Control via Ethernet Port............14 4.1.1 System Requirements..............14 4.1.2 Start the Software Control Program..........14 4.1.3 Control Interface ................. 14 VEGA-1100 User Manual... - Page 8 VEGA-1100 User Manual viii...
- Page 9 Chapter Introduction...
-
Page 10: Chapter 1 Introduction
Introduction The Advantech VEGA-1100 HDMI 2.0 over IP multicast transceiver system — with bi-directional IR, RS-232, audio extender/extractor, USB 2.0, and video wall support — is designed to boost video/audio transmission distances. Illustratively, it increases transmission distances to up to 100 m (330 ft) over copper and/or 300 m (990 ft) (OM3)/400 m (1320 ft) (OM4) over fiber in ultra-HD 4K2K@60 (4:4:4) format. -
Page 11: Specifications
Wall-mounting case with screws Power supply Power consumption 12.5 Watt [max] Operation temperature 0 ~ 40 °C (32 ~ 104 °F) Storage temperature -20 ~ 60 °C (-4 ~ 140 °F) Relative humidity 20 ~ 90% RH [no condensation] VEGA-1100 User Manual... - Page 12 VEGA-1100 User Manual...
-
Page 13: Chapter 2 Connection Diagram
Chapter Connection Diagram... -
Page 14: Connection Diagram
Connection Diagram VEGA-1100 User Manual... -
Page 15: Panel Description
DIP Switch Position Description ON [↓] OFF [↑] Reserved ON [↓] ON [↓] Reserved PIN#1 PIN#2 OFF [↑] ON [↓] Reserved OFF [↑] OFF [↑] Reserved ON [↓] Select transmission over SFP PIN#3 OFF [↑] Select transmission over copper VEGA-1100 User Manual... - Page 16 Stereo IN: Connect to analog stereo audio source. Indicator LED: HDMI out signal LED. Indicator LED: HDMI in signal LED. HDMI OUT: Connect to a HDMI display with a HDMI male-male cable. HDMI IN: Connect to a HDMI source with a HDMI male-male cable. VEGA-1100 User Manual...
-
Page 17: Chapter 3 Ir Pass-Through
Chapter IR Pass-through... -
Page 18: Ir Pass-Through
IR Receiver If necessary, users can buy replacement IR extension cables that are compatible with the definition of the IR sockets for the extender. However, IR cables longer than 2 m (6 ft) may not work. VEGA-1100 User Manual... -
Page 19: Hdmi Pin Definition
Pin 15 Pin 6 TMDS Data1– Pin 16 Pin 7 TMDS Data0+ Pin 17 DDC/CEC Ground Pin 8 TMDS Data0 Shield Pin 18 +5V Power Pin 9 TMDS Data0– Pin 19 Hot Plug Detect Pin 10 TMDS Clock+ VEGA-1100 User Manual... - Page 20 VEGA-1100 User Manual...
-
Page 21: Chapter 4 Operation Approach
Chapter Operation Approach... -
Page 22: Software Control Via Ethernet Port
Type – VID – PID (15-over Copper/16-over Fiber) b. Output Device ID (derived from the device MAC address) c. IP address d. Input Device ID e. Firmware version Users can click the button to edit the device name. VEGA-1100 User Manual... - Page 23 “Fastswitch” can choose from three preset resolutions. Users can also click “Start” or “Stop” to start the video and stop the video. In addition, if you want to disconnect the input and output of the device, click “Leave”. * The "Fastswitch" mode does not support HDR. VEGA-1100 User Manual...
- Page 24 HDMI and I2S. Then click “Start” or “Stop” to start the audio or stop the audio. After completing the audio mode settings, drag the input device to output device to do input/output mapping. Users can also click “Leave” to disconnect the input and output of the device. VEGA-1100 User Manual...
- Page 25 "Local". If it is connected to a mouse or keyboard, select "Remote". After com- pleting the settings, power cycle the device, and drag the input device to the output device to do input/output mapping. After this, users can use the mouse or keyboard to control the computer via USB routing. VEGA-1100 User Manual...
- Page 26 * Please save the firmware file (.bin) & software in the same folder. – Device Mode Transmitter: set the device as the transmitter Receiver: set the device as the receiver Transceiver: set the device as the transceiver VEGA-1100 User Manual...
- Page 27 Hex Codes and send IR commands to the device via infrared routing. Select “Sent to all device” to send IR commands to all devices at once. * Please search for keywords related to Infrared Hex Code online for more com- mands. Multiview VEGA-1100 User Manual...
- Page 28 1920x1080@30 inputs). Users can adjust the FPS of the screen in the Sur- face on the right. Rename Select device and enter the New ID. Then click "Apply" to apply the device name. If you want to reset the ID, please select device and click the “Reset”. VEGA-1100 User Manual...
- Page 29 VEGA-1100 User Manual...
- Page 30 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2022...