Clarion VRX 815 VRX815 VRX815 Owners & Installation Manual page 37

Touch the [EDIT] key to show VSE adjusting dis-
play, in which the properties of currently selected
pattern can be adjusted.
By pressing the [BAND] button in BASIC pat-
tern selecting display or USER pattern selec-
tion/memory display you can switch between the
two patterns, BASIC and USER.
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
Setting and storing VSE Properties/
Memory into USER Pattern
1. Repeat the steps 1 and 2 of the previous pro-
cedure (Calling VSE BASIC Pattern/USER
pattern) to show BASIC pattern selecting dis-
play or USER pattern selection/memory dis-
play.
2. Touch the [EDIT] key to show the VSE adjust-
ing display.
3. Select an item to be adjusted by touching
[ITEM] key in the VSE adjusting display.
The VSE adjustment contents are as follows:
"CAR LENGTH"
Compensates for the length of the car's inte-
rior (longitudinal direction).
"CAR WIDTH"
Compensates for the width of the car's interior
(lateral direction).
"DIFFUSE"
Compensates for special impression.
4. Touch the [w] or [z] key to make the adjust-
ment.
The adjustment range is to 1 to 10 for each
time.
5. After making adjustments to a desired pattern
by repeating the steps 3 and 4, touch the [RTN]
key to change over to the BASIC/USER pat-
tern selection/memory display.
6. Press and hold one of [DIRECT] button for 2
seconds or longer to store the adjusted VSE
pattern to the USER memory.
7. To set a title of the stored USER pattern, touch
the [TITLE] key to change into the [TITLE IN-
PUT] key.
For title inputting method, refer to the section
"Entering titles".
8. Press the [A-M] button to change into the
STANDARD display.
Professional mode/P.EQ opera-
tions
P.EQ effect ON/OFF
The factory default setting is "ON".
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [P.EQ ON/OFF] key to select "on"
and "off".
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
4. After the setting, press the [A-M] button again
or touch the [RTN] key to return to the STAN-
DARD display.
Note:
• If the P.EQ effect is set to OFF, the adjustment made
in "P.EQ operations" is not reflected in the music
source.
Calling P.EQ BASIC Pattern/USER
Pattern
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [z] key to select "P.EQ BASIC" and
"P.EQ USER" mode.
Touch the [P.EQ BASIC] and [P.EQ USER] key
to show BASIC pattern selecting display or
USER pattern selection/memory display.
3. In the pattern selecting display, touch the one
of pattern key to call corresponding P.EQ pat-
tern. In this display, pressing the No. button in
corresponding to the [DIRECT] key can also
call the P.EQ pattern.
After selecting the P.EQ Pattern, touch the
[MEMO] key to copy the select pattern to the
USER pattern.
Touch the [EDIT] key to show P.EQ adjusting
display, in which the properties of currently se-
lected pattern can be adjusted.
By pressing the [BAND] button in BASIC pat-
tern selecting display or USER pattern selec-
tion/memory display you can switch between the
two patterns, BASIC and USER.
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
DSP operations
41
VRX815