Download Print this page
Clarion VRX815 Service Manual
Clarion VRX815 Service Manual

Clarion VRX815 Service Manual

Am/fm cd player/cd changer controller with 7" lc display

Advertisement

SPECIFICATIONS

FM tuner section
Frequency range:
87.9MHz to 107.9MHz(VRX815)
87.50MHz to 108.0MHz(VRX815P)
Usable sensitivity:
11dBf
50dB quieting sensitivity:
Alternate channel selectivity: 70dB
Stereo separation:
35dB(1kHz)
Frequency response:
30Hz to 15kHz(
AM tuner section
Frequency range:
530kHz to 1710kHz(VRX815)
531kHz to 1629kHz(VRX815P)
Usable sensitivity:
25
CD player section
System:
Compact disc digital audio system
Frequency response:
17Hz to 20kHz(
Signal to noise ratio:
98dB(1kHz)IHF-A
Dynamic range:
95dB(1kHz)
Distortion:
0.02
Audio amplifier section
Rated power output:
17W
Maximum power output:
180W(45W
Speaker impedance:
4
Input section
Video input:
1.0
(input impedance 75
Audio input:
130
10k
Video output section
Video output:
1.0
Ω
LCD monitor section
Screen size:
7-inch wide type
(152mm Width
Display method:
Transmission type TN Liquid
Crystal Display
Clarion Co., Ltd.
5-35-2, Hakusan, Bunkyouku, Tokyo, 112-8608 Japan
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: 048-443-1111 FAX:048-433-6996
I
L
N
D
V
R
D
17dBf
3dB)
±
V
μ
1dB)
±
4(20Hz to 20kHz,1%,4
×
4 JEITA)
×
(4 to 8
)
Ω
Ω
0.2Vp-p
±
)
Ω
60mVrms(input impedance
±
or greater)
Ω
0.2Vp-p(output impedance 75
±
)
85mm Height)
×
Service Manual
AM/FM CD Player/CD Changer
Controller with 7" LC Display
Model
(QC-6800B)
Model
(QC-6800K)
Drive method:
Pixels:
General
Power source voltage: 14.4V DC
Ground:
Current consumption: 4.0A(1W)
Auto antenna rated current:
Dimensions(mm):
Weight:
NOTES
)
Ω
Use a CeNET extension cable that is less than 20m in
length.(including the Y-adapter CCA-519)
We cannot supply PWB with component parts in prin-
ciple. When a circuit on PWB has failure , please repair
it by component parts base. Parts which are not men-
tioned in service manual are not supplied.
Some CDs recorded in CD-R mode may not be usable.
Even when recorded in CD-RW mode, some CDs not
be usable.
CD-ROM discs cannot be played in the CD changer.
This unit can display title data for CD-text CDs and user
titles input with this unit.
This slide mechanism is used the special adjustment jig
for repair.
Specifications and design are subject to change without
notice for further improvement.
- 1 -
Published by Service Dept.
298-5950-00 Nov.2001 P
Printed in Japan
TFT(thin-film transistor) active
matrix driving
336,960(1440
234)
×
(10.8 to 15.6V allowable)
Negative
500mA less
Main unit
178(W)
50(H)
165(D)
×
×
Tuner amp unit
178(W)
37.5(H)
209.5(D)
×
×
Remote control unit
44(W)
110(H)
27(D)
×
×
Main unit
2.0kg
Tuner amp unit
1.1kg
Remote control unit
30g
(including battery)
VRX815
VRX815P

Advertisement

loading
Need help?

Need help?

Do you have a question about the VRX815 and is the answer not in the manual?

Questions and answers

Summary of Contents for Clarion VRX815

  • Page 1: Specifications

    Drive method: TFT(thin-film transistor) active ■ matrix driving FM tuner section Pixels: 336,960(1440 234) × Frequency range: 87.9MHz to 107.9MHz(VRX815) General 87.50MHz to 108.0MHz(VRX815P) Power source voltage: 14.4V DC Usable sensitivity: 11dBf (10.8 to 15.6V allowable) 50dB quieting sensitivity: 17dBf Ground:...
  • Page 2   If extensive damage is caused due to negligence of re- Machine screw(M4 714-4008-81   × pair, the legal responsibility shall be with the repairing Parts bag(Use only VRX815) −−−−− company. DCP lock spacer 335-6747-00   5. Cautions regarding chips.
  • Page 3: System Check

    USA to outside the USA or from outside the USA to inside the USA. Any station preset memories are lost when the recep- ※ tion area is changed. VRX815 - 3 - VRX815P...
  • Page 4: Block Diagram

    BLOCK DIAGRAM ■ Tuner amp unit section VRX815 - 4 - VRX815P...
  • Page 5 Main unit section VRX815 - 5 - VRX815P...
  • Page 6 Input a color bar signal.(PAL) 9: XC OUT : O : Sub system clock. Adjust L702 so that the wave form of TP11 is in focus. pin 10: RESET_ : IN : Reset signal input. VRX815 - 6 - VRX815P...
  • Page 7 : O : LCD back light ON signal output. pin 72: NU : - : Not in use. 4: GREEN 1 : O : Signal output for the LED. pin 73: NU : - : Not in use. VRX815 - 7 - VRX815P...
  • Page 8 : O : The chip selection signal output to the OSD pin 75: SEG 15 : O : Segment output terminal. pin 76: SEG 14 : O : Segment output terminal. pin 37: OSD PS 2 : O : The input/output port number signal output VRX815 - 8 - VRX815P...
  • Page 9 : IN : The CD text data input. pin 99: NU : - : Not in use. pin100: CD SBCK : O : The clock pulse output to read the text data of the CD. VRX815 - 9 - VRX815P...
  • Page 10: Parts List

    SLIDE MECHANISM −−−−− 331-3228-00 MECHANISM BRKT(F) 331-3227-00 CONNECTOR PLATE 331-3229-00 MECHANISM BRKT(R) 331-3231-00 IC-HOLDER 948-0629-00 CD MECHANISM 039-1972-00 FLEXIBLE PWB 286-9851-00 SETPLATE(VRX815) (WITHOUT COMPONENT) 286-9853-00 SETPLATE(VRX815P) 311-1831-00 LOWER CASE 347-6624-00 SHIELD FILM 347-6578-00 INSULATOR(LCD) 780-2003-20 SCREW((M2×3) 039-1863-00 PWB(FPC) 714-3004-81 MACHINE SCREW(M3×4) 714-2605-81 MACHINE SCREW(M2.6×5)
  • Page 11 347-6583-00 SPRING HOLDER 345-8598-00 CUSHION 370-5932-01 ESCUTCHEON 013-9706-00 SWITCH ASSY 382-6104-01 BUTTON(DSP/ISR) 379-0458-01 INDICATOR(7'LCD) 335-6651-00 FILTER DCP ASSY 345-8599-00 SLIDER −−−−− 370-5933-01 ESCUTCHEON(DCP) 335-6490-00 BUTTON GUIDE 382-6096-00 BUTTON(RELEASE) 371-5685-00 TRIM PLATE 382-6097-00 BUTTON(EJECT) 750-3495-00 SPRING(PUSH OUT) VRX815 - 11 - VRX815P...
  • Page 12 310-1649-02 UPPER CASE 074-1213-01 OUTLET SOCKET(13P) 702-3008-81 TAP SCREW(3×8) 075-9002-02 JACK(AUDIO OUT) 714-3006-81 MACHINE SCREW(M3×6) 013-3949-00 SWITCH(RESET) 716-0878-00 IT SCREW(M2.6×5) 013-5102-00 SLIDE SWITCH(DSP/NORMAL) 714-2612-81 MACHINE SCREW(M2.6×12) 880-2084C TUNER PACK 714-2605-81 MACHINE SCREW(M2.6×5) 073-0768-90 TERMINAL 060-8021-07 AUTO FUSE(15A) VRX815 - 12 - VRX815P...
  • Page 13 (1),then remove the rib. Pull the PWB in the direction indicated with the arrow (2),then remove the PWB from the pawl. (Figure B) 5. While paying attention not to damage the FPC, remove the PWB. VRX815 - 13 - VRX815P...
  • Page 14 Do not remove part T (No.33 temporary fastening 4. Fit the optical pickup into the groove of the traverse as- screw for gear fixing plate). sembly. (Figures G and G-1) 5. Fit the lead screw into the hole. (Figure G-2) VRX815 - 14 - VRX815P...
  • Page 15 658-0230-56 SLIDER 658-0230-25 GEAR C 658-0230-57 CLAMPER ARM 658-0230-26 ROLLER LEVER GEAR 658-0230-58 TRIGGER ARM 658-0230-27 ROLLER GEAR A 658-0230-59 RUBBER 658-0230-28 ROLLER GEAR B 658-0230-60 CLAMPER 658-0230-29 ROLLER IDLER 658-0230-61 CLAMPER PLATE 658-0230-30 L LOCK CAM VRX815 - 15 - VRX815P...
  • Page 16 VRX815 - 16 - VRX815P...
  • Page 17: Electrical Parts List

    R431 119-1031-15 1/16W 10kΩ C586 168-1045-56 0.1μF J406 074-1100-70 R432 032-0104-66 1/4W 470Ω J501 074-1205-00 50P CCT421 050-0122-50 1/16W10kΩ×4 J R433 119-6811-15 1/16W 680Ω CCT422 050-0122-50 1/16W10kΩ×4 J J502 074-1048-57 7P R434 119-2721-15 1/16W 2.7kΩ VRX815 - 17 - VRX815P...
  • Page 18 C795 166-5601-52 56pF RH D702 001-3211-90 MA335-TX C801 168-1045-56 0.1μF C747 042-0416-57 10V47μF D703 001-0367-91 1SS226 C748 178-1052-78 1μF C802 042-0416-57 10V47μF D704 001-0529-29 MA8051-M C803 042-0416-57 10V47μF C749 042-0397-53 25V0.47μF TAN D801 001-7046-01 NSPW310BS-A,RS VRX815 - 18 - VRX815P...
  • Page 19 VR708 012-6009-61 100kΩ Q906 190-1461-00 2SA1461 R770 119-2421-15 1/16W 2.4kΩ X701 061-3520-95 3.57945MHz R701 119-4711-15 1/16W 470Ω R771 119-1031-15 1/16W 10kΩ X702 061-3524-90 4.433618MHz R702 119-4721-15 1/16W 4.7kΩ R772 119-1031-15 1/16W 10kΩ X801 061-3521-90 4.9152MHz VRX815 - 19 - VRX815P...
  • Page 20 042-0592-58 16V10μF C197 042-0592-50 6.3V22μF C315 163-1063-35 16V10μF C114 042-0592-58 16V10μF C198 042-0592-50 6.3V22μF C316 163-1063-35 16V10μF C115 042-0592-58 16V10μF C199 042-0592-58 16V10μF C317 168-1022-55 1000pF C116 168-2212-55 220pF C200 042-0592-58 16V10μF C318 168-1032-55 0.01μF VRX815 - 20 - VRX815P...
  • Page 21 051-0350-93 NJM4558M Q357 125-2004-93 RN1403 R105 119-1031-15 1/16W 10kΩ IC102 051-3015-90 NJM4580M Q358 190-1313-00 2SA1313O,Y R106 119-1031-15 1/16W 10kΩ IC103 051-1811-90 BA3129F Q359 192-2712-00 2SC2712 R107 119-1031-15 1/16W 10kΩ IC104 051-5008-90 M62419FP Q360 100-1431-00 2SA1431 VRX815 - 21 - VRX815P...
  • Page 22 R266 119-2231-15 1/16W 22kΩ R340 119-0000-05 1/16W 0Ω JW(Use R152 119-4731-15 1/16W 47kΩ R153 119-2721-15 1/16W 2.7kΩ R267 119-3311-15 1/16W 330Ω only VRX815) R268 119-3311-15 1/16W 330Ω R155 119-4721-15 1/16W 4.7kΩ R341 119-1031-15 1/16W 10kΩ R269 119-3311-15 1/16W 330Ω R342 119-1031-15 1/16W 10kΩ...
  • Page 23 658-0231-04 1μF Z 658-0230-70 B3HB00000014 658-0231-29 1/10W 330Ω 658-0230-84 0.22μF K 658-0230-67 2SA1037AKTXR 658-0231-28 1/10W 1kΩ 658-0230-91 0.01μF K 658-0230-68 UN211F 658-0231-30 1/8W 2.2Ω 658-0231-04 1μF Z 658-0230-68 UN211F 658-0231-31 1/10W 1.5MΩ 658-0230-85 0.1μF K VRX815 - 23 - VRX815P...
  • Page 24 658-0231-25 1/10W 22kΩ 658-0230-72 k0L1BA000015 117-1001-10 1/10W 10Ω 658-0231-20 1/10W 470Ω 658-0230-73 k0L1BA000019 658-0231-35 1/10W 100Ω 658-0231-25 1/10W 22kΩ 658-0230-74 H2D400400008 658-0231-35 1/10W 100Ω 658-0231-14 1/10W 10kΩ 658-0230-75 HDJ169500008 658-0231-35 1/10W 100Ω 658-0231-35 1/10W 100Ω VRX815 - 24 - VRX815P...
  • Page 25 CIRCUIT DIAGRAM Tuner PWB(B3) section 1/4 - 25 - VRX815 VRX815P...
  • Page 26 Tuner PWB(B3) section 2/4 VRX815 - 26 - VRX815P...
  • Page 27 Tuner PWB(B3) section 3/4 - 27 - VRX815 VRX815P...
  • Page 28 Tuner PWB(B3) section 4/4 VRX815 - 28 - VRX815P...
  • Page 29 H R/R SP +(PUR) BACK UP(YEL) J ACC(RED) K ILLUMI.(ORG/WHT) L PARKING(LIGHT GRN) M PHONE INT.(BRN) N AMP-ON(BLU/WHT) O NC P R/R SP -(PUR/BLK) EXTENSION LEAD 854-6388-50 PUR/BLK GRN/BLK BLU/WHT LIGHT GRN GRY/BLK ORG/WHT WHT/BLK VRX815 - 29 - VRX815P...
  • Page 30 CIRCUIT DIAGRAM Main PWB(B1) section 1/2 VRX815 - 30 - VRX815P...
  • Page 31 Main PWB(B1) section 2/2 VRX815 - 31 - VRX815P...
  • Page 32 PRINTED WIRING BOARD Main PWB(B1) / Inner switch PWB(B4) section SLAVE-ON BUS - BUS + VIDEO OUT ILLUMI. TO TUNER AMP UNIT IR OUT 10 VIDEO GND 11 CD-L 12 CD GND 13 CD-R VRX815 - 32 - VRX815P...
  • Page 33 CIRCUIT DIAGRAM Inner switch PWB(B4) section VRX815 - 33 - VRX815P...
  • Page 34 LCD PWB(B2)section 1/2 VRX815 - 34 - VRX815P...
  • Page 35 Panel switch PWB(B5) / LCD PWB(B2) section 2/2 VRX815 - 35 - VRX815P...
  • Page 36 PRINTED WIRING BOARD LCD PWB(B2) / Panel switch PWB(B5) section VRX815 - 36 - VRX815P...
  • Page 37 EXTENSION LEAD(2P) CD mechanism : Servo PWB(B6) section DRIVE MOTOR ASSY (SOLDER SIDE) to MAIN UNIT FLEXIBLE PWB (SENSOR) SPINDLE MOTOR ASSY to PICK UP unit (PARTS SIDE) VRX815 VRX815P...
  • Page 38 PRINTED WIRING BOARD CD mechanism : Servo PWB(B6) section VRX815 - 38 - VRX815P...

This manual is also suitable for:

Qc-6800bVrx815pQc-6800k