Intermec EasyCoder 601 XP Installation Instructions Manual
Cutter kit
Hide thumbs
Also See for EasyCoder 601 XP:
- Service manual (171 pages) ,
- Installation and operation manual (107 pages) ,
- User manual (36 pages)
Related Manuals for Intermec EasyCoder 601 XP
Summary of Contents for Intermec EasyCoder 601 XP
-
Page 1: Installation Instructions
Installation Instructions Cutter Kit (for EasyCoder PX4i, PX6i, 501 XP, and 601 XP printers) - Page 2 Th e information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and service Intermec- manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec.
-
Page 3: Table Of Contents
Contents Introduction Description... 2 Installation Step-by-step instructions ... 6 Controlling the Cutter Fingerprint... 10 IPL ... 10 Maintenance and Troubleshooting Cleaning...12 EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions Contents... - Page 4 Contents EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions...
-
Page 5: Introduction
Introduction Th is chapter describes the cutter kits for EasyCoder PX4i, PX6i, 501 XP, and 601 XP printers. EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions... -
Page 6: Description
PX4i/PX6i printers, but the same principles apply to EasyCoder 501 XP/601 XP printers. Th e cutter supports both Intermec Fingerprint and IPL. Th e cutter unit is fi tted on the same hinges as the front door, which it replaces, and is connected by a single cable to the DIN-connector on the printer’s front. - Page 7 Chapter 1 — Introduction EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions...
- Page 8 Chapter 1 — Introduction EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions...
-
Page 9: Installation
Installation Th is chapter describes how to install the cutter on an EasyCoder PX4i/PX6i or 501 XP/601 XP printer. No tools are required. EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions... -
Page 10: Step-By-Step Instructions
• Switch off the power and remove the power cord. • Open the printer’s front door. • Hold the printer fi rmly and press the front door sideways to the left so as to disengage the hinges. • Remove the door completely. - Page 11 • Switch off the power. Tilt down the cutter and route the paper through the cutter unit between the guide plates (also see the User’s Guide for the printer in question). Th en tilt up the cutter again and lock it in closed position.
- Page 12 Chapter 2 — Installation EasyCoder PX4i/501 XP Cutter EasyCoder PX6i/601 XP Cutter EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions...
-
Page 13: Controlling The Cutter
Controlling the Cutter Th is chapter describes how the cutter is controlled using Intermec Fingerprint or IPL. EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions... -
Page 14: Fingerprint
Chapter 3 — Controlling the Cutter Fingerprint Th e cutter is activated by CUT or CUT ON statements, see the Intermec Fingerprint Progarmmer’s Reference Manual, or the Intermec Direct Protocol Programmer’s Reference Manual. Application programs may have related facilities for operating the cutter. -
Page 15: Maintenance And Troubleshooting
Th is chapter describes how to troubleshoot and clean the cutter. EasyCoder PX4/6i & 501/601 XP Cutter Kit Installation Instructions Maintenance and Troubleshooting... -
Page 16: Cleaning
Chapter 4 — Maintenance and Troubleshooting Cleaning Th e cutter mechanism becomes accessible when the cover is opened. Th e cutter shears will need to be cleaned from adhesive residue if the cutter has been used for cutting through labels, something that is not advisable. - Page 20 Intermec Technologies Corporation Corporate Headquarters 6001 36th Avenue West Everett, WA 98203 tel 425.348.2600 fax 425.355.9551 www.intermec.com EasyCoder PX4/6i & 501/601XP Cutter Kit Installation Instructions *1-960631-00* *1-960631-00*...