HITROL HTM (HPV)-20N Series Instruction Manual
  1. Manuals
  2. Brands
  3. HITROL Manuals
  4. Switch
  5. HTM (HPV)-20N Series
  6. Instruction manual

HITROL HTM (HPV)-20N Series Instruction Manual

Vibration type level switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HITROL CO., LTD.
HEAD OFFICE, FACTORY, R & D INSTITUTE
HITROL CO., LTD. 141, Palhakgol-gil, Jori-eup
Paju-si, Gyeonggi-do, Korea
TEL.: (+82)-31-950-9700
FAX : (+82)-31-943-5600
www.hitrol.com
Doc. no. : HTM(HPV)20N_IM_Eng_Rev.2.1
Issue date: 2019. 12
INSTRUCTION MANUAL
VIBRATION TYPE LEVEL SWITCH
HTM (HPV)-20N Series
HITROL CO., LTD.
HTM(HPV)-20N Series
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HTM (HPV)-20N Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HITROL HTM (HPV)-20N Series

Summary of Contents for HITROL HTM (HPV)-20N Series

  • Page 1 HTM(HPV)-20N Series HITROL CO., LTD. HEAD OFFICE, FACTORY, R & D INSTITUTE HITROL CO., LTD. 141, Palhakgol-gil, Jori-eup Paju-si, Gyeonggi-do, Korea TEL.: (+82)-31-950-9700 FAX : (+82)-31-943-5600 www.hitrol.com INSTRUCTION MANUAL VIBRATION TYPE LEVEL SWITCH HTM (HPV)-20N Series Doc. no. : HTM(HPV)20N_IM_Eng_Rev.2.1 Issue date: 2019.

  • Page 2: Table Of Contents

    Warranty and Contact • • • • • • • • • • •• 15 Relay Delay Time Adjustment ∙ ∙ ∙ ∙ ∙ ∙ ∙ 11 Relay Out Control ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙ ∙∙ 11 HITROL CO., LTD.

  • Page 3: Product Overview

    As such, the electric signal is reduced to stop the oscillation of the piezo sensor. The electric signal is detected by the electronic circuit to operate the relay, so that the state can be detected with the contact output. HITROL CO., LTD.

  • Page 4: Specifications

    Process Connection PT 1–1/2'' (M) PT 1–1/2'' (M) (Std.), 2'' FLANGE Housing; Cable Entry AL.; 2-PF 3/4'' (F) (Std.), Installation Side Side and Top Contact Rating AC 250 V, 5 A / DC 30 V, 5 A HITROL CO., LTD.

  • Page 5: Dimensions

    HTM(HPV)-20N Series Dimensions <WEATHER-PROOF> HTM-20N(H)-B HTM-20N(H)-A HTM-20N-C <SCREW TYPE> <FLANGE TYPE> HITROL CO., LTD.

  • Page 6: Ex-Proof Version

    HTM(HPV)-20N Series <Ex-PROOF> HPV-20N(H)-B HTM-20N(H)-B HPV-20N(H)-A <SCREW TYPE> <FLANGE TYPE> HITROL CO., LTD.

  • Page 7: Attachment And Cautions

     Avoid the inlet to install the sensor and maintain enough distance to prevent direct contact with the content.  If the housing temperature rises because of direct sunlight, install a sun cover to prevent such occurrence. HITROL CO., LTD.
  • Page 8 15° or more. It also must be installed to keep the wide part of the wing vertical. The cable type must be installed vertically. Ⅹ Ⅹ The screw-type socket must under 24 mm. Otherwise, dust may enter, resulting in malfunction. < FIG. 1 > HITROL CO., LTD.

  • Page 9: Technical Data

    500 N HTM-20N-C Max. Process Pressure Up to 10 kg/cm (150#) HTM (HPV)-20N-A / HTM(HPV)-20N-B Up to 2 kg/cm HTM-20N-C Relative Humidity Good for 0–100% (Ratio between the vapor in the air and that required saturation same temperature) HITROL CO., LTD.

  • Page 10: Amp And Wiring

    HTM(HPV)-20N Series AMP and Wiring The power specifications of HTM (HPV)-20N Series is AC 90–240 V and DC + 24 V, Check and supply the power voltage before wiring, and then connect it to the output according to use.  LED...

  • Page 11: Activation Point Setting

    You can change the state of the output contact. (N.C.  N.O.  …  N.C.) Press and hold the buttons for 1 second to turn on and off the green LED and thus finish the setting. HITROL CO., LTD.

  • Page 12: Led Color And States

    - When measuring sticky material, check if such material grows. Remove them regularly if any should appear. The sticky material may cause malfunction and damage to the device. Turn off the power of the product for maintenance. HITROL CO., LTD.

  • Page 13: Failure Check

    ■ Install an ex-proof product in an ex-proof zone. ■ Do not bend or extend the sensor that vibrates. ■ Make sure to install the product and the cover before supplying the power. HITROL CO., LTD.

  • Page 14: Cautions For Grounding

    - Pay attention to prevent electric shock. ■ Disposal - Make sure to separate the AMP and main unit from the housing before disposing the product. No part has an influence on the environment, so special attention is not required (e.g., mercury switch). HITROL CO., LTD.

  • Page 15: Label

    You can request for A/S through our website or by contacting our headquarters. Headquarters Factory Research Center Address: Hitrol, 141, Palhakgol-gil, Jori-eup, Paju-si, Gyeonggi-do, Republic of Korea (Palhakgol-gil 98) HITROL CO., LTD. 141, Palhakgol-gil, Jori-eup, Paju-si, Gyeonggi-do, Korea TEL.: 031-950-9700 (Headquarters and A/S)

Table of Contents