Advertisement
LPG test point adaptor (if using LPG)
10
根據檯面厚度安裝固定支架
Floating nut
Fibre washer
x 4
LPG Models
從下面往上看
Washer
adaptor (if using LPG)
16-20mm
20 mm
12
連接氣源
.
液化石油氣
確保把壓力調節到2.90 kPa，
把所有爐頭打到最大火力。
p 3 CLEARANCE DIMENSIONS.
r D certi ed, with an Rp ½" (ISO 7 1) female thread connection.
所有型號
and comply with relevant AS 5601/NZS 5261 requirements.
確保接頭在安裝氣體煮食爐之後便於接觸。
為了便於斷開氣源，確保在靠近氣體煮食爐的地方安裝隔離閥。
n or permanently deformed.
如果用軟管連接氣源：
ot surfaces
確保軟管足夠長，便於拆除氣體煮食爐進行維修。
rbench oven etc.)
確保接頭位置間隙如第5步所述。
軟管必須是通過認證的Rp ½" (ISO 7 1)母螺紋。
To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.
軟管必須盡可能短，必須符合當地相關法律法規的要求。
Check for a well de ned blue ame without any yellow tipping.
軟管不得打結，否則容易造成磨損或永久性變形。
If any abnormality is evident, check that the components of the burner assembly are located properly
軟管不得靠近或接觸任何發熱表面（例如金屬發熱板底部、煙道或灶台下面的烤箱底板等）。
If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.
30-40mm
The cooktop must not be used by the customer until proper operation has been achieved.
Elbow (½" BSP external thread)
Make sure to t the supplied
washer and test point adaptor.
Make sure the supply pressure
is regulated to 2.75 kPa, with
the two semi-rapid burners
operating at highest setting.
50 mm
recessed to 50 mm
20-30mm
30-40mm
煤氣
確保把壓力調節到1.5 kPa
（香港）或0.8 kPa（新加坡），
把所有爐頭打到最大火力。
40mm+
11
固定在檯面上
ALL NG Models
Make sure to t the supplied elbow
Adjust to obtain a pressure of 2 kPa at the appliance with Dual Wok burner operating on High.
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut o by the customer, make sure the connection
is tted with an isolating valve close to the cooktop.
If connecting the gas with a exible hose:
+50 mm
Ensure the hose is long enough to allow for removal of cooktop for servicing.
40mm+
Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.
The hose assembly must be as short as practicable and comply with local regulations.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, ue, or chassis of underbench oven etc.)
13
檢查所有接頭是否漏氣
ON
開
lifting o
lifting o
對其他三面重複此步驟
氣體
GAS
yellow tip
good ame
x 4
24
yellow tip
good ame
x 4
check all connections
Advertisement
