1. Manuals
  2. Brands
  3. ULTRASUN Manuals
  4. Personal Care Products
  5. E6
  6. Manual

ULTRASUN E6 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for ULTRASUN E6

Summary of Contents for ULTRASUN E6

  • Page 2: Warning

    • • In order to keep your Ultrasun machine in compliance with the standard, you have to make sure to change lamps, components and accessories with original lamps, components and accessories only. Otherwise guarantee will be taken off as well as any responsibility and any liability.

  • Page 3: Table Of Contents

    Please check if the serial number plate at the back side of this user manual resembles the serial number plate at the back of the sunbed. Ultrasun spends a lot of time and attention on the development and improvement of the delivered products. Ultrasun holds the right to make changes without informing you previously.

  • Page 4: Explaining The Icons

    This user manual consists of all het possible options which you can have on your Ultrasun E6. If these options are not relevant to your sunbed, then you can skip the chapters indicated as “option”. The user manual of your Ultrasun E6 consists of this user manual and a separate user manual for the IQ Touch Control.

  • Page 5: Part Of The E6

    Parts Of The E6 To guarantee safe and easy transportation, the sunbed is packed in several separate parts as shown in the drawing below. These parts can be assembled easily by two people at the place where you want to locate the sunbed.

  • Page 6: Assembling The E6

    On the next pages the assembling of the E6 is explained. The chapter “Additional assembling instructions E6” gives several extra instructions. Assembling The E6 Note: Always disconnect the power supply before disassembling and during assembling. Step 2...
  • Page 7 Attention: The parts do not stand up straight by themselves. Make sure that you get help for assembling.

  • Page 8: Additional Assembly Instructions E6

    DC: See page 12 for details Single Phase 220V + PE Additional Assembling Instructions E6 Please put all the parts together as is shown in the previous drawings. At first assemble the base plate like in the drawing, may this already be pre-assembled you can skip this step. Slightly fasten all nuts and bolts by hand.
  • Page 9 STEP 2: Assemble the topcooler (E) with the cap nuts (F) and the washers (C). STEP 3: Place the pillar (G) between the brackets of the topcooler (E) and the bottom frame (A). The wire tacks on the bottom side fall in the similar holes and on the top side the bolts (I) and the washers (H) are fixed.

  • Page 10: Installing The Mp3/Ipod/Tablet Holder (Option)

    Installing The MP3/iPod/Tablet Holder* (Option) The holder for your MP3 player, iPod or tablet should be installed as shown on the drawings: position the holder 35 mm (1) under the edge of the box where the audio jack comes out and make sure the holes and that the holder of the faceplate match (2).

  • Page 11: Audioconnections (Option)

    Audio Connections* (Option) When your E6 is equipped with the “music ” option, an extra bass box is provided which can be attached to the backside of the cooling pillar. The cooling pillar is now equipped with an MP3 or IPod connection and holder (See previous chapter).

  • Page 12: Additional Cooling Fan

    Additional Cooling Fan - Before you place the pillar between the parts, attach the housing of the fan (I) to the pillar with the screws (R) and connect the plugs from both sides. - Now it is possible to attach the pillar as described in the above assembling description.

  • Page 13: Connecting The Strap On The Topcooler (Option)

    Connecting The Strap On The Topcooler* (Option) A strap can be optional offered and connected to the topcooler. Smaller people whom normally cannot reach the metal handle, now can hold on to this strap to get a better tan. The strap can be mounted or replaced by taking the screw out of the strap holder.

  • Page 14: Connecting The Remote Control

    (the smooth and ribbed side must be in accordance with each other). In case larger distances must be bridged or in case disturbances in the pipes arise, the possibility exists to place an Opto-box (Ultrasun article number 3T0480) between the remote control pipes.

  • Page 15: Troubleshooting And Maintenance

    • Pay attention to strange noises in the sunbed; • Clean the acrylics after every tanning session; • Consult an authorised service agent in the event your Ultrasun machine has a failure; Many parts can be recycled, so keep them separate and do...

  • Page 16: Rgb Controller With Distance Controller

    RGB Led Controller With IR Distance Control Your tanning device is equipped with a RGB led controller and a remote control with which you can control the colour settings of the Rainbow-led strip. With the led controller (Fig.P:A) you can set the colour changing, colour jumping, etc.

  • Page 17: Changing Lamps And Starters

    Attention: Make sure that the new lamps and starters are of the same type as the previous ones. In order to keep your Ultrasun machine in compliance with the standard, you have to make sure to change lamps, components and accessories with original lamps, components and accessories only.
  • Page 18 Notice the following tanning rules for proper and safe use of your tanning device : The exposure time for first session must not be shorter than 1 minute. • • Follow the recommendations concerning exposure duration and exposure intervals • Protect your eyes from visible and infrared radiation, take adequate precautions ! Always use the provided sunglasses! •...

  • Page 19: Removing The Acrylics

    Remove cosmetics well in advance of exposure and do not apply any sunscreens. • According to basic standards your Ultrasun tanning equipment needs to be equipped with original parts and lamps. In every other case the guarantee is taken off as well as any responsibility and any liability.

  • Page 20: Service Parts

    Service Parts Besides that this Ultrasun E6 is equipped with high quality parts, there is a possibility that parts get exposed to mechanical erosion. When this happens these parts need to be replaced. In the table “Technical product information” specific article numbers of the lamps are mentioned. In the separately enclosed electrical scheme the article numbers of the electrical parts are mentioned in the inscription.
  • Page 21 DISCLAIMER Ultrasun pays close attention to the quality of its products. This also applies to the information in this user manual. Ultrasun reserves the right to change the content of this manual at any time. Though Ultrasun strives to always display the correct texts and images in her manuals, errors can occur. We cannot be held responsible for any errors in writing or printing.

  • Page 23: Declaration Of Conformity

    DECLARATION OF CONFORMITY Directive 2014/35/EU and 2014/30/EU Ultrasun International BV Granaatstraat 6 7554 TR HENGELO, Holland declare that this Ultrasun E6 is in conformity with the actual version of following normative documents: Applied harmonized Standards: Safety: EN 60335-1 Safety: EN 60335-2-27...

Table of Contents