Operating Instructions & Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Teel Submersible Effluent and
®
Sewage/Solids Handling Pumps
Description
Teel submersible effluent pumps, Model Numbers 4RK62 and 4RK63, and
sewage/solids handling pumps, Model Numbers 4RK45, 4RK46, 4RK47, 4RK48 and
4RK49 are used for sewage, effluent and wastewater removal, sump drainage,
liquid transfer systems, circulation, dewatering, and flood control. Pump motors
range from 230V single phase with automatic thermal reset to 230/460V three
phase. 60 hertz, oil filled, 1 HP, 1
of head with capacities ranging from 20 to 250 GPM.
Volute and semi-open impeller are close grained cast iron. Dual shaft seal,
extended pump out vanes and seal plate barrier provide greater seal protection.
Effluent pumps have 3/4" spherical solids handling capability. Sewage/solids
handling pumps handle 2" spherical solids. Stainless steel hardware for easy
disassembly after extended use. All pumps are manually operated except Model
4RK62, which has an automatic float switch.
Unpacking and Inspection
Handle with care. Check items received
against packing list to be sure that all
equipment has been received. Inspect
for shipping damage. If found, file
claim with carrier immediately.
Specifications
Volts
@
Models
HP
60 Hz.
4RK45
1
230
4RK46
1
230/460*
4RK47
1
⁄
230
1
2
4RK48
1
1
⁄
230/460*
2
4RK49
2
230
4RK62
2
230
4RK63
2
230/460*
* These models are pre-wired at factory for 230V.
Dimensions
Models
Base
4RK45
Cast iron
4RK46
Cast iron
4RK47
Cast iron
4RK48
Cast iron
4RK49
Cast iron
4RK62
Cast iron
4RK63
Cast iron
Form 5S4184
4RK45, 4RK46, 4RK47, 4RK48, 4RK49, 4RK62 and 4RK63
1
⁄
HP, and 2HP models deliver from 38 to 85 feet
2
General Safety Information
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol.
When you see this symbol on your
pump or in this manual, look for one of
the following signal words and be alert
to the potential for personal injury.
Motor
Circuit Breaker
Full Load
Phase
Amps
1
8.5
3
8.5/4.1
1
12.0
3
9.0/4.7
1
13.0
1
11.0
3
7.5/3.8
Pump Materials
Housing
Cover
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Cast iron
Printed in U.S.A.
09319
0201/020/E3
Maximum
Rating
Fluid
(Amps)
Temperature
15
130° F
15/15
130°
15
130°
15/15
130°
20
130°
15
130°
15/15
130°
Dimensions
Impeller
Height
Cast iron
20
⁄
"
1
2
Cast iron
20
1
⁄
2
Cast iron
20
1
⁄
2
Cast iron
20
1
⁄
2
Cast iron
20
1
⁄
2
Cast iron
18
⁄
1
2
Cast iron
18
⁄
1
2
Warns about
hazards
that will cause serious personal injury,
death, or major property damage if
ignored.
Warns about
hazards that can
cause serious personal injury, death, or
major property damage if ignored.
Warns about
hazards that will or
can cause minor personal injury or
property damage if ignored.
NOTE: Indicates special instructions
which are important but not related to
hazards.
NOTE: Pump must be installed in a
vertical position only. Installing pump
in any other position will void
warranty.
Service
Sewage/solids handling
Sewage/solids handling
Sewage/solids handling
Sewage/solids handling
Sewage/solids handling
Effluent
Effluent
Cord
Diameter
Length
16
⁄
"
20'
7
8
16
7
⁄
20
8
16
7
⁄
20
8
16
7
⁄
20
8
16
7
⁄
20
8
16
⁄
20
7
8
16
⁄
20
7
8
E
N
G
L
I
S
H
E
S
P
A
Ñ
O
L
Discharge
NPT (in.)
3"
3
F
3
R
3
3
A
2
N
2
Ç
A
I
S
Weight
117 lbs.
121
122
121
122
120
120
®
Need help?
Do you have a question about the 4RK45 and is the answer not in the manual?
Questions and answers