Related Manuals for Hussmann RID
Summary of Contents for Hussmann RID
- Page 1 ROLL IN DELI/DAIRY DISPLAY P/N IGUP-RID-9610(9911) INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
HUSSMANN CHINO PRODUCT CONTROL The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and re- placement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial num- ber of each piece of equipment involved, in order to pro- vide the customer with the correct parts. -
Page 3: Cut & Plan Views
Rev. 9610(9911) RID01, SINGLE DEPTH 4'-5 " ROLL-IN CARTS " RID-01 " RID012 SINGLE DEPTH 8'-10 " ROLL-IN CARTS " 1'-6 " SINGLE DEPTH 3" 6" Drain ELEC. FLEXED ASSEMBLED IN FIELD DRAIN IS 1" PLASTIC TUBE REFRIG. STUBBED UP THROUGH TOP Elec. -
Page 4: Installation
Case must be raised correctly, under legs where support is best, to prevent damage to case. The RID case is tall and narrow and can be tipped over if it is raised too high on one side. JOINING... -
Page 5: Plumbing
Rev. 9610(9911) WARNING: DO NOT LET ANY WEIGHT BEAR DOWN ON THE COIL ASSEMBLY. USE 5 GALLON BUCKETS OR SIMILAR UNDER THE CANOPY TO HOLD THE WEIGHT WHILE THE BEAM IS BEING ATTACHED. THE FORK HOLES ON THE BEAM SHOULD FACE TOWARD THE OUTSIDE EDGE OF THE CANOPY. -
Page 6: Refrigeration
The fans can be accessed by removing the lower interior rear panels. THERMOSTAT LOCATION The thermostat is located within the case in the ceiling on the right hand side (facing front of case). To access the T- stat remove the 4"X4" access panel. IGUP-RID-9610(9911) TX VALVE ON RIGHT... -
Page 7: Electrical
Actual ampere draw may be less than specified. Field wiring from the refrigeration control panel to the merchandisers is required for re- frigeration thermostats. Most component amperes are listed in the “Case Specs” section, but always check the serial plate. -
Page 8: User Information
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro- tection required always: 1. -
Page 9: Maintenance
TOWARD THE MOTOR. Maintenance COPPER COILS The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers. Hussmann recommends using #15 Sil-Fos for repairs. -
Page 10: Electrical And Refrigeration Specifications
2700 12° 36° 28° 450 Optional 2700 12° 36° 28° 450 Optional 2700 12° 36° 28° 450 Optional RID-02 Double Sided/Single Depth 2700 12° 36° 28° 450 Optional 2/60 2700 12° 36° 28° 450 Optional 2/60 2700 12° 36° 28°... -
Page 11: Appendices
Rev. 9610(9911) APPENDIX A. – Temperature Guidelines The refrigerators should be operated according to the manufacturer’s published engineering specifications for entering air temperatures for specific equipment applica- tions. Table 1 shows the typical temperature of the air entering the food zone one hour before the start of defrost and one hour after defrost for various categories of refrigerators. -
Page 12: Appendix D. - Recommendations To User
1.2 Load levels as defined by the manufacturer must be observed. 1.3 The best preservation is achieved by following these rules: IGUP-RID-9610(9911) - Page 13 Rev. 9610(9911) a) Buy quality products. b) Receive perishables from transit equipment at the ideal temperature for the particular product. c) Expedite perishables to the store’s storage equip- ment to avoid unnecessary warm-up and pro- longed temperature recovery. Food store refrig- erators are not food chillers nor can they reclaim quality lost through previous mishandling.
- Page 14 IGUP-RID-9610(9911)
- Page 15 On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure.
-
Page 16: Hussmann ® Chino 13770 Ramona Avenue • Chino, California
The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit. Please note them below for future reference. MODEL: SERIAL NUMBER: IGUP-RID-9610(9911)