Table of Contents
Advertisement
Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1)
engine.SysSGCPRetryTimerInterval = 1000
engine.SysCLIval = false
engine.SysToneDetect = false
engine.SysNumTrans = false
engine.SysMinOverlap = 0
engine.SysMaxOverlap = 28
engine.SysGSMTimerInterval = 10000
engine.LCMMdlFile = ../lib/lcm
engine.CCMdlFile =
engine.mdoDir = ../lib/
engine.VersionTimeoutValue = 10000
engine.MDLANumberScreening = 0
engine.SysMdlMemoryReduction = 1
engine.CircuitReservation = false# Do/Don't use circuit reservation feature
engine.CallBackDBCleanUpTimer = 3600000
(min:600000 to max:10800000
engine.SendHardwareBlock = false
*.MaxNumTGAdvances = 1# Limit on num Trunk Group Advance actions
*.RedirectingATree = 0
*.ClearingLocation = 0
the Clearing Location field in Call Context
*.DefaultLocation = 0
not override the Default Location field in Call Context
*.detailedCallEventCapture = 1
*.SelectTermCustGrpId = 0
SigPath CustGrpId is 0000.
*.GlareReattemptCauseValue = 44
*.DerivedInterworkingFCIBCIEnable = 0
R2/T1CAS/ISDN/H323 V2
*.sipModeSelectionControl =
proxy mode via the dialplan, 2 - Fixed Proxy mode, always work in proxy mode.
*.sipRoutingMode = 0 # 0 - strict-router, 1 - loose-router.
#The following two lines are call based memory allocator settings.
#set these to 0 to disable call-based memory allocator
#This setting is memory efficient, but performance suffers.
#set these to 110000 for maximum performance. Memory usage increases.
engine.CALL_MEM_BLOCK_SIZE = 65536
engine.CALL_MEM_CHUNK_SIZE = 56
# engine.SysTraceLevel = 3
*.LongCallTime = 21600000
def)
engine.CDRencodingFormat
engine.CDRtimeStamp
engine.CDRmessageTypes
engine.VersionTimeoutValue = 10000
engine.StartUpAuditEnabled = false
engine.FaultRecoveryAuditTimer = 15000
engine.CustSpecificINAPHandling = null
engine.DisableMultipleCDRs = 1
engine.ChargingTariffType = 0
engine.ChargingMode = 1
engine.ShortDurationCallPeriod = 0
engine.ActionOnChargeTableAccessFailure = 0
engine.CallLimitingControl = 0
Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide
D-22
# interval between retransmission (msec)
#
GSM to be sent (milliseconds)
# LSI call model
../lib/cc
# call context
# where .mdo files live
# Interval for version messages (msec)
# use calling party number for a number screening
)
# false=PGW will only send maintenance blocks
# 0 = Normal mapping behaviour, LCM will not override
# 0 = Normal protocol defined default value, LCM will
# 1= Select Terminating SigPath CustGrpId if Originating
# 0= Always select Originating SigPath CustGrpId
# used for re-attempt by GW in Nailed configurations.
# 1 = Set FCI/BCI values when interworking with
2
# = 2
# used to configure OnGoingCallTime in ms (6hrs
= AnsiCDB
= M
= "1010,1020,1030,1040,1050,1060,1070"
# audit invoked at engine startup?
# milliseconds
# 0=enable, 1=disable
# 0=tariff-rate/scale-factor, 1=meter pulse
# 1=AddOnCharge, 2=ReplaceCharge, 3=FreeOfCharge
# 0=feature disabled
# 0 = Call limiting off, 1 = Call limiting on
Appendix D
# Call Back DB clean up timer in mini seconds
# 1 - B2BUA mode, allow later selection of
# 0=continue call, 1=release call
Sample Installation Scripts
OL-18083-14
Advertisement
Table of Contents
