Related Manuals for Narwal T10
Summary of Contents for Narwal T10
- Page 1 Narwal Robot Mop & Vacuum with Self-Cleaning Station User Manual Please read this product manual carefully before use and keep it properly. Due to continuous product renewal, please refer to the actual product. Model：YJCC002 Market Model: YJCC002-R YJCC002-B...
- Page 2 Dear customer: Thank you for choosing Narwal Robot Mop & Vacuum, we are committed to providing you with hands-free cleaning experience. If you have any question, please contact: support@narwalrobotics.com For more details, please visit Narwal official website: www.narwalrobotics.com Wish you a happy experience of using Narwal.
- Page 3 Precautions This product is only used for floor cleaning in the home environment. Do not use it outdoors (such as open balcony), non-ground (such as sofa, window sill), elevated surface, commercial or industrial environment. 1 Do not use it in an elevated 2 Do not place any objects (including 3 Do not put your hair, fingers, surface (such duplex floor or...
- Page 4 Precautions Do not let the robot inhale hard or 5 Do not place the robot near heat Please use the following sharp objects. and water sources (eg radiators and methods to move the robot if faucets). needed.
- Page 5 Warning This product is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervisor instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.
- Page 6 Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 7 1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 2. The operating temperature of the EUT can’t exceed 40℃ and shouldn’t be lower than 5℃ . Hereby, Yunjing Intelligence Technology (Dongguan) Co., Ltd. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU.
-
Page 8: Table Of Contents
Table of content Introduction Maintenance What's in the box Robot About the robot & base station Base station Accessories Installation Base station installation Trouble shooting Robot preparation Specifications How to use Narwal Tips Warranty policy Basic operation Mapping Vacuum/Mop Cleaning path... - Page 9 What's in the box Robot x1 Base station x1 Sweeping module x1 Side brush x2 Bird knife x1 Mopping module x2 Mop x4 Magnetic strip x1 Power cord x1 Detergent x1 Filter sponge x2...
- Page 10 About the robot & base station Reset button • Press and hold for 3 seconds to reset Open lid Power button • Press and hold for 2 seconds to turn on/off Cover Start button • Short press to start/pause cleaning •...
- Page 11 Filter Filter buckle Dust bin buckle Dust bin handle...
- Page 12 About the robot Market Model: YJCC002-R Cliff sensor Bumper Omni-directional wheel Sweeping module mounting port Mopping module mounting shaft Suction inlet Main wheel Lidar Battery...
- Page 13 Bumper Speaker Air vent Wall sensor Obstacle avoidance sensor Charging electrode...
- Page 14 Base station Market Model: YJCC002-B Power outlet Sewage tank inlet Pumping port Air inlet Clean water tank outlet Charging electrode Guide pulley Overflow sensor Clean water spout Sewage pumping port Air vent Washboard...
- Page 15 Sewage tank float Water tank handle Water tank buckle Water inlet Cover lid Clean water tank cover Sewage tank cover Sewage tank buckle Clean water tank Sewage tank Filter sponge...
- Page 16 Base station panel Base station screen & buttons OLED screen Home button • Short press to command the robot to return/exit the base station. • Press and hold for 2 seconds to reset the map and start mapping. Circular indicator light Start button •...
- Page 17 Screen icon Sweeping icon Charging icon Narwal icon Indicates the current Indicates that the robot Indicates that the base status is vacuuming. and base station charging station/robot has been electrodes are connected turned on/off successfully. Mopping icon Battery icon Child lock icon...
- Page 18 Cleaning modules Sweeping module Module lid Mounting magnet Side brush Suction inlet Sweeping module mounting shaft...
- Page 19 Mopping module Handle Mop velcro M o p p i n g m o d u l e mounting port...
-
Page 20: About The Robot & Base Station
Base station installation 1. Power-on 2.Base Station placement Connect the power cord to the back socket of the base Keep the base station on a flat surface, against a wall. station, plug it into the power outlet. Note: please fasten Note: ensure to leave enough space to the charging the power cord to avoid poor connection. -
Page 21: Robot Preparation 1
Robot preparation 1. Turn on 2. Install & remove the 3. Install & remove the Press and hold the power button sweeping module mopping module 2 seconds to turn on the robot. Note: Insert the protrusions under the Install the mop on the module and do not move the robot when it is sweeping module into the slot and press the mounting port into the... -
Page 22: How To Use Narwal Tips 1
How to use Narwal tips 1. Please put away all wires on the 2. Do not move the base station after 3. Do not move the washboard when ground (including the power cord of mapping, it will cause the robot fails... - Page 23 4. The robot can go across the obstacles less than 1.5cm 5. Please place the magnetic strip at the around areas you in height. do not wish to clean before the robot starts to work. Magnetic strip 1.5cm...
-
Page 24: Basic Operation 1
Basic operation Robot basic operation Power on/off • Press and hold the power button for 2 seconds to turn on/off RESET Button Start task • Short press the start button to start a new task. Pause/resume task • Short press the start button to pause/resume. - Page 25 Base station operation Send home/exit base station • Short press the home button to command the robot return/exit the base station. Start task • Short press the start button to start a new task. Pause/resume task • Short press the start button to pause/resume.
-
Page 26: Mapping 1
Mapping 1. Long press the home button on the base station to start the mapping. 2. The robot scans all rooms along the contour of the room to create a map of the entire house. 3. After mapping, the robot will return to the base station for room division and charging. -
Page 27: Vacuum/Mop 1
Vacuuming Mopping 1. Install the sweeping module. 1. Install the mopping module. 2. Short press the start button on the base station or on 2. Short press the start button on base station or the robot to start vacuuming. robot to start mopping. 3. - Page 28 Cleaning path Vacuuming path Mopping path The robot will clean from the room of base station for To avoid secondary contamination, the robot will clean from vacuuming by default. the farthest room for mopping by default.