Advertisement
Advertisement
Table of Contents
Related Manuals for Narwal Wet Dry Vacuum S10 Pro
Summary of Contents for Narwal Wet Dry Vacuum S10 Pro
- Page 1 User Manual Narwal Wet Dry Vacuum S10 Pro Model: YJSC001...
-
Page 2: Product At A Glance
The manual may be updated from time to time based on product updates and user feedback. Please scan the QR code below to browse the o icial website and view the latest version. In case of any problem in using the product, please contact Narwal after-sales customer service through the following ways: Customer service email: support@nawal.com(North America) -
Page 3: How To Use
Self-cleaning base Main Parts Wet Dry Vaccum Charging contacts Winding post Power cord Hot air outlet Screen Cleaning tray Side air inlet How to Use Mode bu on Power On/O bu on On the initial startup, a language switch reminder page will appear. - Page 4 How to fill the clean water tank Mode bu on When cleaning the floor Short press: switch the mode (Smart/Turbo/Quiet/Suction) 1. Take out the clean water tank 2. Add clean water Press and hold: start MAX enhancement; release to end Pull out the clean water tank to take it out.
-
Page 5: Cleaning And Maintenance
Cleaning and Maintenance Suggested Maintenance Cycle Main part Part Suggested maintenance cycle Dirty water tank Clean after every use MAX Enhancement:During the cleaning process, Low Areas Mode Clean after every use and replace every when encountering extremely stubborn stains When the angle between the handle and the 3 6 months that are hard to handle, you can activate MAX floor is below 25°, the machine will automatical-... - Page 6 Pipe Clean regularly on demand · If the machine prompts a high dirt level when the · Rinse the solid waste box and the filter slot. Please rinse floor is free from obvious dirt and after several the filter slot You can open rounds of self-cleaning, the pipe may be dirty;...
-
Page 7: Fault Warning
Problem Analysis and Troubleshooting Stuck roller The product pauses and The roller brush fails to work Please remove the roller brush brush broadcasts "Roller brush stuck. properly because it is stuck to check if there is any foreign Please clean it." The outer ring of by hair or other foreign ma er blocking it. -
Page 8: Specifications
Q Why are my floors ge ing dirtier when the product is working? Q Why does the product keep prompting that “High dirt level detected. Please put the product back onto the base for self-cleaning” after self-cleaning is completed? A It is possibly because the floors are too dirty and there is too much dirt on the roller brush, so it is recommended that you put the product back on the base for self-cleaning. - Page 9 Bluetooth (Wet Dry Vacuum) Ba ery (Wet Dry Vacuum) Ba ery Type: Rechargeable Li-ion Ba ery Protocol: BLE 5.0 Ba ery Pack Quantity Per Pack: 1 pcs Frequency Range: 2402 2480MHz Quantity of Ba ery Cells Per Ba ery Pack: 6 pcs Max.
- Page 10 Manufacturer:Yunjing Intelligence Innovation (Shenzhen) Co., Ltd. Address:Room A2901, Yunzhongcheng, Building 1, Vanke Yuncheng VI, Dashi 2nd Road, Xili Community, Xili Street, Nanshan District, Shenzhen, Guangdong, China WWW.NARWAL.COM...
Need help?
Do you have a question about the Wet Dry Vacuum S10 Pro and is the answer not in the manual?
Questions and answers
I press the self cleaning button with the unit on the base and the voice prompt continues to to tell met to place the unit on the base for self cleaning.
The Narwal Wet Dry Vacuum S10 Pro gives a voice prompt to place the unit on the base for self-cleaning when the self-cleaning button is pressed because the floors may be very dirty, causing excess dirt to accumulate on the roller brush. Additionally, there may be residual dirt in the pipe due to a lack of regular cleaning and maintenance. Placing the unit on the base allows it to perform the self-cleaning process properly.
This answer is automatically generated