Advertisement
PARTS LIST
(One Joining Kit per Two M1GLE-93)
Item
Quantity
1.
6
2.
2
3.
2
4.
8
5.
4
6.
4
7
2
8.
1
9.
1
10.
2
11.
2
12.
2
13.
8
14.
20
15.
2
All equipment should be thoroughly examined for
shipping damage before and during unloading.
This equipment has been carefully inspected at
our factory. Any claim for loss or damage must
be made to the carrier. The carrier will provide
any necessary inspection reports and/or claim
forms.
Every effort is made to ship all parts for the kit.
The Hussmann Service Center can be reached by
calling
• from U.S. & Canada 1-800-922-1919 •
• from Mexico 1-800-522-1900 •
©2008 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
U.S. & CANADA 1-800-922-1919 • MEXICO 1-800-522-1900 • WWW.HUSSMANN.COM
®
Merchandisers
Description
Screw - Phillips Head - #8-18 x
Gasket Tape 1 x
5
/
5
5
/
-18
16
5
/
Silicone Sealer
Top Trim - 10
Bumper - Top
Bumper - Bottom
Bracket - End Splashguard
Screw - SM Hex Head - TEK2 - #8-18 x
Splashguard Support
1
/
2
1
/
x 180
2
1
-18 x 3
/
in.
16
2
/
16
5
/
16
1
-18 x 5
/
in.
16
2
1
/
in. x 84-in.
2
(C
)
UT TO FIT
(C
)
UT TO FIT
M1GLE-93
Joining
Back-to-Back
1
/
2
P/N 0503478_A
April 2008
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hussmann Impact M1GLE-93
Summary of Contents for Hussmann Impact M1GLE-93
-
Page 1: Table Of Contents
• from U.S. & Canada 1-800-922-1919 • • from Mexico 1-800-522-1900 • ©2008 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. U.S. & CANADA 1-800-922-1919 • MEXICO 1-800-522-1900 • WWW.HUSSMANN.COM ® Description Screw – Phillips Head – #8-18 x Gasket Tape 1 x... - Page 2 Place shims under front and back rail at cross-members. Figure 1 — Remove Studs and Replace Screws Serial Plate Figure 2 — Position and Level First Case U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM Levels...
- Page 3 M1LGE-93 Joining Honeycomb Figure 3 — Remove Honeycomb Figure 4 — Remove Interior Back Panels HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM Interior Back Panels P/N 0503478_A Remove the honeycomb as shown in Figure 3. Lift up and out to remove the interior back panels.
- Page 4 • Do not butt gaskets; always overlap them as shown. • Remove paper backing after gasket has been applied. • Perimeter gasket required by NSF. Detail U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM Insert Alignment Pins A continuous bead of...
-
Page 5: Cap Screw
Figure 6 — Move Second Case Figure 7 — Location of Cap Screws in Side Frames -inch Figure 8 — Drill Holes in Back Frame HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM -inch P/N 0503478_A Position Second Case Alignment pins guide the mating of the frames. -
Page 6: Hex Nut 5
Cap Screws – 3, over Cap Screws – 5, and over Hex Nuts – 7. Adjust color panels on each side to minimize any gaps. Figure 9 — Apply Silicone U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM... -
Page 7: Top Trim
M1LGE-93 Joining Figure 10 — Install Top Trim Top Rail Trim Figure 11 — Install Top Rail Trim HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM P/N 0503478_A From one side, slide Top Trim – 9 under price tag moldings on top of cases to cover gap as shown in Figure 10. - Page 8 Replace honeycomb and retainers as shown in Figure 15. Shipping Braces Figure 13 — Remove Braces and Install Bumpers Figure 14 — Remove Protective Film Honeycomb Figure 15 — Replace Honeycomb U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM Shipping Braces...
- Page 9 Figure 16 — Install Splashguard Brackets Bracket Splashguard Splashguard Figure 17 — Install Splashguards HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM 1. Check to be sure that all Base of Case 2. Position top of splashguard 3. Push the lower edge of the...
Need help?
Do you have a question about the Impact M1GLE-93 and is the answer not in the manual?
Questions and answers