Hussmann IMPACT RL Installation Instructions Manual
Reach-in merchandisers
Hide thumbs
Also See for IMPACT RL:
- Installation and operation manual (40 pages) ,
- Installation instruction (12 pages) ,
- Install manual (7 pages)
Advertisement
Quick Links
Reach-in Merchandisers
PARTS LIST
Item
RL/RM
RLN
RM/RMF
RMN
1.
2
2.
1
3.
1
4.
6
5.
6
6.
1
7.
5
8.
1
NOTE: Be sure first merchandiser
has been leveled according to the
main installation instruction.
Carefully unpack and inspect the
joining parts listed above to verify
completeness and that there is no
damage.
1
Prepare cases for joining (both
sides of islands) as shown in
Figure 1.
A. Remove bumpers, rails,
packing materials, and splash-
guards from the both cases.
B. Remove shelves (if
installed).
C. Remove display racks and
pans from ends to be joined.
D. Remove rear shelf supports.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
®
Merchandisers
Quantity
RLNI
RLNIE
RLT
2
4
2
1
2
2
1
2
1
6
12
6
6
12
6
1
2
1
5
10
5
1
2
1
Raceway
Splashguard
SIDE VIEW
RLT
SIDE VIEW
RLN / RMN / RLNI / RLNIE
Splashguard brackets must
Description
be installed before piping
Donut Gasket
Gasket, 1 x
1 /2
x 180 in.
Gasket,
1 /2
x
1 /4
x 180 in.
Cap Screw
5 /16
-18 x 1
Split Lock Washers
Joint Molding
Binder Post and Screw
Splice Connector
B
A
Bumper
Bumper
Retainer
A
A
Bumper
Bumper
Retainer
Splashguard
Figure 1. Prepare Cases
RL / RM / RMF, RLT
Joining Instructions
or wiring case.
1 /4
5 /16
E
C
C
P/N 0387177F
October 2005
D
1
Advertisement
Related Manuals for Hussmann IMPACT RL
Summary of Contents for Hussmann IMPACT RL
-
Page 1: Joining Instructions
B. Remove shelves (if installed). C. Remove display racks and pans from ends to be joined. D. Remove rear shelf supports. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® RLN / RMN / RLNI / RLNIE Description RLNI Donut Gasket... - Page 2 Alignment Pin G. RLNI Only: Remove screws and interior top panel on both sides of the island case end to be joined (see Figure 1). RLNI Only HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
- Page 3 Block Figure 2. Remove Shipping Block (One From Each Side of Island Models) Shipping Brace HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. O NOT USE SHIPPING BOLTS TO JOIN CASES RLNI / RLNI Figure 3. Remove Shipping Braces P/N 0387177F...
- Page 4 Figure 4A or 4B. RLT has no Alignment Pin Figure 4A. Verify Nut Retainer Installation Factory Installed Nut Retainer RL / RM / RMF RLN / RMN Factory Installed Nut Retainer HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
- Page 5 Reach-in Joining Instruction P/N 0387177F RLNI Alignment Pin Alignment Pin Figure 4B. Verify Nut Retainer Installation HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
- Page 6 Part 2; 5B or 5C, Part 2. RL / RM / RMF RLN / RMN Figure 5A, Part 1. Apply Gasket to Left End of RL/RM/RMF and RLN/RMN HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers Apply the wider Foam Tape Gasket —...
-
Page 7: All Models
ALL MODELS: Apply gasket between wipes. Figure 5A, Part 2. Apply Gaskets to Right End of RL/RM/RMF and RLN/RMN HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • Lap gaskets at lower corners. • Check that there are no gaps between gasket and case. - Page 8 ® P/N 0387177F Merchandisers RLNI Donut Gaskets Must Be Applied As Shown Figure 5A. Apply Gaskets to Left End of RLNI HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
- Page 9 Shown Make sure area where raceway attaches to end frame is covered with wider 1 in. x Figure 5B. Apply Gaskets to Right End of RLNI HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. RLNI Donut 1 in. x in. x in.
- Page 10 ® P/N 0387177F Merchandisers Donut Figure 5C, Part 1. Apply Gasket to Left End of RLT HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
- Page 11 Reach-in Joining Instruction Donut 1 in. x in. x Figure 5C, Part 2. Apply Gasket to Right End of RLT HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0387177F...
- Page 12 Do not to cut wires routed along the front bumper retainer. See detail in Figure 6. Figure 6. Move Cases Together HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers The RLT has no alignment pin and the wireway is at the top...
- Page 13 Figure 7A. Joining Sequence for RL, RM, RMF, RLN and RMN Cases Nut Retainer Figure 7B. Joining Sequence for RLT Cases HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0387177F Loosely insert Cap Screw – 5 with Lock Washer – 6 into...
- Page 14 ® P/N 0387177F Merchandisers RLNI RLNI Alignment Pin Alignment Pin Nut Retainer Figure 7C. Joining Sequence for RLNI Cases HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
-
Page 15: Side View
Figure 8. Installing “J” Molding Splashguard Splice Connector Figure 9. Installing Splashguard Splice Connector HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Align holes in frame with holes in Joint Molding – 6. Fasten cases together using Binder Post and Screws –...