Advertisement
Quick Links
For Medium Temperature Merchandisers
PARTS LIST
Item
Quantity
19" Front
23" Front
1.
1
2.
1
3.
4
4.
12
5
2
6.
2
7.
8
8.
8
9.
2
10.
4
11.
2
12
2
13.
2
14.
4
15.
4
16.
1
17.
2
18.
8
Note:
Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each
merchandiser.
e sure Merchandisers have
B
been leveled according to the
installation instructions.
Carefully unpack and inspect
the Joint Kit making sure
there is no breakage or
damage.
R
S
1
EMOVING
HIPPING
Remove Bolts, Washers and
Nuts from Shipping Braces.
Then remove the shipping
brace Brackets. See Figure 1
and Detail A.
After removing the braces
and brackets, make sure to
replace the screws that hold
the top panels in place.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
®
Description
1 /
1
Gasket
2
1 /
1
Gasket
2
4
Joining Brackets
12
Hex Washer Head SM Screw
4
Cap Screw
4
Flat Washer
8
Cap Screw
8
Flat Washer
2
Cap Screw
4
Flat Washer
2
Lock Washer
5 /16
2
Hex Nut
2
Threaded Rod
4
Flat Washer
1 /2
4
Hex Nut
1
Butyl Tape
2
Splashguard Joint Support
8
Hex Head Sheet metal Screw #8 x
B
.
RACES
D5ELE/D5EE END CASES
JOINING INSTRUCTION
1 /
x
x 60
2
5 /
x 1
x 120
8
3 /
10 -16
4
5 /16
-18 x 4
5 /16
1 /4
- 20 x 1
1 /4
5 /16
1 /
- 18 x 2
2
5 /16
5 /16
- 18
1 /2
-13 x 15
1 /2
-13
1 /2
Bracing
Sheet Metal
Screws
Detail A
Fig. 1. Removing Shipping Braces
TO D5 PARENT CASE
Side View
July, 2000
P/N 407199
1
Advertisement
Related Manuals for Hussmann IMPACT D5ELE
Summary of Contents for Hussmann IMPACT D5ELE
- Page 1 Detail A. After removing the braces and brackets, make sure to replace the screws that hold the top panels in place. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) D5ELE/D5EE END CASES TO D5 PARENT CASE JOINING INSTRUCTION Description...
- Page 2 Figure 3. Fig. 2. Removing Components from Case Retainer Clips here both sides. (2) on D5ELE (4) on D5 EE See Detail “B” page 5. Fig. 3. Locating Nut Retainers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) ®...
- Page 3 JOINING INSTRUCTION Gasket D5 Parent Case 23” HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Fig. 4. Installing Gasket P/N 407199 Apply Gasket - 1 in the hori- zontal recess across the bottom and up front to cover slots.
- Page 4 Parent case Model D5L Parent Case Fig. 5. Sequence of bolting cases together Joining Brackets Joining Brackets (2) on End Case Model D5ELE End Case HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) ® (3) Screws each Top View...
- Page 5 Detail B D5EE Case Model Retainer Nut Detail B Detail C HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Use Cap Screws – 7 with Flat Washers – 8 to draw merchandisers together at rear. Start at the bottom, below the coil baffle, then middle, then top;...
- Page 6 Install splashguards and lower front panels according to I/O manual. See Figure 9. Fig. 9. Installing Splashguards Fig. 7. Applying the Butyl Tape Typical both sides Fig. 8. Installing Splashguard Retainers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) ®...
- Page 7 Top Rail Bumpers Fig. 10. Installing Bumpers and Top Rails HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Install lower bumper on end case both sides. Push into place. Add full length bumpers flush with bumper and offset across joints, making sure no gaps exist between sections.