Specifications - Makita HM1802 Instruction Manual

ENGLISH
(Original instructions)
1 Switch lever
2 Power-ON indicator lamp
(green)
3 Service indicator lamp (red)
4 Soft grip

SPECIFICATIONS

Model
Blows per minute
Dimensions
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for heavy chiselling and demolition
work as well as for driving and compacting with
appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
ELECTRIC BREAKER SAFETY WARNINGS
Safety instructions for all operations
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Explanation of general view
5 Bolt
6 Triangle alignment mark
7 Bit with collar
8 Bit without collar
9 Bit
HM1802
29.4 kg
Additional safety warnings
ENE046-1
1.
ENF002-2
2.
3.
4.
GEA010-2
5.
6.
7.
8.
9.
GEB239-1
10. Do not touch the bit, parts close to the bit, or
11. Some material contains chemicals which may
12. Do not touch the power plug with wet hands.
13. Before operation, make sure that there is no
14. Do not operate the tool at no-load unnecessarily.
SAVE THESE INSTRUCTIONS.
10 Tool retainer
11 Tool holder
12 Notched portion of the bit
870
843 x 210 x 608 mm
/II
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly
recommended that you wear a dust mask and
thickly padded gloves.
Be sure the bit is secured in place before
operation.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for
a while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high
locations.
Hold the tool firmly with both hands.
Keep hands away from moving parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not point the tool at any one in the area
when operating. The bit could fly out and injure
someone seriously.
workpiece immediately after operation; they may
be extremely hot and could burn your skin.
be toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
buried object such as electric pipe, water pipe
or gas pipe in the working area. Otherwise, the
bit may touch them, resulting an electric shock,
electrical leakage or gas leak.
HM1812
31.3 kg
3