jbc NAS Instruction Manual
  1. Manuals
  2. Brands
  3. jbc Manuals
  4. Rework stations
  5. NAS
  6. Instruction manual

jbc NAS Instruction Manual

2-tool nano rework station
Hide thumbs Also See for NAS:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
NAS
2-Tool Nano Rework Station

Advertisement

Table of Contents
loading

Related Manuals for jbc NAS

Summary of Contents for jbc NAS

  • Page 1 INSTRUCTION MANUAL 2-Tool Nano Rework Station...

  • Page 2: Packing List

    This manual corresponds to the following references: - NASE-9C (100V) - NASE-1C (120V) - NASE-2C (230V) Packing List The following items are included: Nano Control Unit ..1 unit Nano Handle ....1 unit Adjustable Nano Ref. NT115-A Tweezers ......1 unit Ref.

  • Page 3: Features And Connections

    Features and Connections Cable Collector Accessorie not included: Tool extension cord (1m) Stand: Ref. A1205 Intelligent Heat Management Process Screen: 2.8 Color TFT Cartridge Extractor and Tip Aligner Tip Aligner Metal Brush Brass Wool AN115 USB-A Connector NT115 Adjustable Nano Nano Handle Tweezers USB-B...
  • Page 4 Tool Stand Assembly Tool Stand Replacement Loosen the screw (1) and withdraw the tool Insert the new tool stand (3) and tighten the stand (2) . screw (4).

  • Page 5: Work Screen

    Work Screen NAS offers an intuitive user interface which provides quick access to station parameters. Default PIN: 0105 Status Bar 17:14 Tool NT115 in use ºC Power Temp. Levels indicator Power Port Displayed if temperature levels are activated Station Information...

  • Page 6: Advanced Functionalities

    Insert a USB flash drive into the USB-A connector to save your soldering process in csv format. Files Station update Download the JBC Update File from www.jbctools.com/software.html Insert the USB flash drive with the file downloaded to the station. Update System Notifications The following icons will be displayed on the screen’s status bar.

  • Page 7: Operation

    Operation JBC’s Exclusive Heating System This revolutionary technology is able to recover tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, tip life increases by 5. 1. Work 2. Hibernation When the tool is lifted from the holder the tip When the tool is in the holder, the power will heat up to the selected temperature.
  • Page 8 The Pedal is frequently used to rework components with tweezers. AN115 JBCs adjustable nano tweezers is the most effective tool for desoldering chip components but also it facilitates its rapid placement and soldering by using P405 pedal connected to JBC´s NAS station.
  • Page 9 Desoldering Iron For this operation JBC´s desoldering station DSS is needed. Manual Solder Paste Dispensing Solder Paste Dispenser Apply the solder paste amount needed to solder the new chip component. The use of JBC´s DPM solder paste dispenser is recommended.
  • Page 10 AN115 Ajustable Nano Tweezers Placing Do not press the pedal. Use the tool to position the component on the previously tinned pad. Note: The inactive tool prevents the component from heating up prematurely. AN115 Ajustable Nano Tweezers Soldering Once in position press and hold the pedal to activate the tool and perform the soldering.

  • Page 11: Changing Cartridges

    Changing Cartridges Save time and change cartridges safely without having to switch the station off. 1. Removing 2. Inserting 3. Aligning Place the cartridge into the Push the cartridge into the Use the holes to rotate extractor slot (1) and pull the handle until the mark*.

  • Page 12: Changing Grips

    Changing Grips 1. Inserting 2. Removing Tabs First put the slide-on Hold the grip and pull tabs into the new grip, the tab. Use a pliers if then push the grip necessary with the tabs onto the handle. Tabs Grip for NT115 Ref.

  • Page 13: Maintenance

    2. Press the new fuse into the fuse holder fuse. If necessary use a tool to lever it off. and replace it in the station. Fuse holder Fuse holder Fuse - Repairs should only be performed by a JBC authorized technical service.
  • Page 14 Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use.

  • Page 15: Specifications

    Specifications 2-Tool Nano Rework Station Ref.: NASE-9C 100V 50/60Hz. Input fuse: 0.5A. Output: 8.5V Ref.: NASE-1C 120V 50/60Hz. Input fuse: 0.5A. Output: 8.5V Ref.: NASE-2C 230V 50/60Hz. Input fuse: 0.2A. Output: 8.5V - Output Peak Power: 14W per tool - Temperature Range: 90 - 450 °C /190 - 840 ºF - Idle Temp.
  • Page 16 In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase. This product should not be thrown in the garbage.

This manual is also suitable for:

Nase-9cNase-1cNase-2c

Table of Contents