Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for jbc NASE-C Series
Summary of Contents for jbc NASE-C Series
- Page 1 www.jbctools.com INSTRUCTION MANUAL Nano Rework Station Ref. NASE-C...
-
Page 2: Packing List
Packing List The following items are included: Control Unit ....1 unit Nano Handle ....1 unit Adjustable Nano Ref. NAE-1C (120V) Ref. NT115-A Tweezers ......1 unit NAE-2C (230V) Ref. AN115-A NAE-9C (100V) Pedal........ 1 unit Metal Brush ....1 unit Cartridge dispenser Case .. - Page 3 w w w.jbctools.com Features Cable collector Accessories not included: Stand: Tool extension cord (1m) Intelligent Heat Management Ref. A1205 Cartridge Process extractor Screen: and tip aligner 2.8 Color TFT Brass wool Metal brush Adjustable Nano Nano Handle USB-A connector Tweezers Ref.
-
Page 4: Cable Assembly
Tool Holder assembly Cable assembly For tool AN115-A For tool NT115-A... -
Page 5: Work Screen
w w w.jbctools.com Work Screen The NASE-C offers an intuitive user interface which provides quick access to station parameters. Default PIN: 0105 Status bar 17:14 17:14 Tool T470 NT115 in use ºC ºC Power Temp. Levels Temp. Levels indicator Power Port Power Port... -
Page 6: Advanced Functionalities
Insert a USB flash drive into the USB-A connector to save your soldering process in csv format. Files Station update Download the JBC Update File from www.jbctools.com/software.html Insert the USB flash drive with the file downloaded to the station. Update System notifications The following icons will be displayed on the screen’s status bar. -
Page 7: Operation
Operation The JBC Exclusive Heating System Our revolutionary technology is able to recover tip temperature extremely quickly. It means the user can work at a lower temperature and improve the quality of soldering. The tip temperature is further reduced thanks to the Sleep and Hibernation modes which increase the tip life by 5. - Page 8 Chip Compoments Rework proces using Tweezers and pedal The Adjustable Nano Tweezers is the most effective tool for desoldering chip components but also it facilitates its rapid placement and soldering by using the P-405 pedal connected to the station. Connections Pedal Ref.
- Page 9 w w w.jbctools.com Pad cleaning Clean the pads with the desoldering tool DS360-A*. * Secondary station is needed. Solder paste dispensing Apply the solder paste amount needed to solder the new chip component.
- Page 10 Placing Use the tool to position the component on the previously tinned pads. Soldering Once in position, press and hold the pedal to perform the soldering.
-
Page 11: Changing Cartridges
w w w.jbctools.com Changing cartridges Save time and change cartridges safely without having to switch the station off. Removing Inserting Aligning Place the cartridge in the slot Push the cartridge into the Use the holes to rotate as shown and pull the handle handle to the mark*. -
Page 12: Changing Grips
Changing grips 1. Push the grip with 2. To remove the the tabs onto the tabs, hold the grip handle. and pull them out. Use a pliers if necessary. Tabs Grip for NT115-A Nano handle Changing the tip cleaning system Replace the tip cleaning system: - Brass wool - Metal brush... -
Page 13: Maintenance
If necessary use a tool to lever it off. and replace it in the station. - Replace any defective or damaged pieces. Use original JBC spare parts only. - Repairs should only be performed by a JBC authorized technical service. - Page 14 Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use.
- Page 15 w w w.jbctools.com 有害物质含量表 产品中有害物质的名称及含量 有害物质 部件名称 六价铬 多溴联苯 多溴二苯醚 铅(Pb) 汞(Hg) 镉(Cd) (Cr(VI)) (PBB) (PBDE) 烙铁头 手柄 电源线 主机 电源插座 保险丝 主开关 电位连接 变压器 线路板 O 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572 规定的限量要求以下。 X 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求。...
-
Page 16: Specifications
170 x 90 x 135 mm (6.70 x 3.54 x 5.31 in) Complies with CE standards ESD Safe Warranty JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse.